Q: My VALBERG AUTOCOFFEE M3 coffee machine starts up by itself after a program - is this normal?

This is completely normal. The VALBERG AUTOCOFFEE M3 coffee machine is programmed to automatically restart certain cycles after the end of a program. Here’s what happens: After a cleaning or descaling cycle : the machine automatically returns to the main menu and may restart a rinsing cycle (70 to 80 seconds) before being ready. Automatic rinsing cycle : after turning on, the device automatically starts a rinsing of 70 to 80 seconds before offering you the menu. Reinsertion of the water tank : if you have just reinserted the tank, the machine pumps water into the internal tubes for 5 to 6 seconds, which may resemble a restart. These behaviors are safety and hygiene features: they ensure that the machine is always rinsed and ready to operate correctly. If the machine restarts abnormally outside of these cases (multiple times in a row without your action, or at the moment you want to turn it off), check that the water tank is properly in place and fully inserted, or consult the troubleshooting section of your manual.

Q: I don't have a cleaning tablet for my VALBERG AUTOCOFFEE M3: what should I do?

This is a common situation: cleaning tablets are not provided with your VALBERG AUTOCOFFEE M3. You need to obtain them separately. What you need to know about the cleaning program: The program lasts 20 minutes You need to place a cleaning tablet in the ground coffee compartment The indicators light up to signal the steps (emptying the tray, filling the tank) Place a container of at least 1.5 liters under the spout before starting the program Where to buy the tablets? You can find them from spare parts dealers (Spareka, Eurosav) or on general websites (Amazon, ManoMano). Just search for "espresso machine cleaning tablets" - they are inexpensive. If you don't have one right now, you can simply ignore this program for now and use it later when you have a tablet.

Q: How to descale the VALBERG AUTOCOFFEE M3 coffee machine?

Duration and Preparation The complete program lasts 40 minutes . You will need a descaler for espresso machines (not provided with the device). Never use pure citric acid, vinegar, or vinegar-based products. Step-by-Step Procedure Step 1: Remove the milk tube and clean it Step 2: Press and hold the descaling button for 3 seconds to start the program Step 3: When the grounds container light flashes, empty the drip tray and the grounds container, then put them back in place Step 4: Fill the water tank with 1 liter of lukewarm water, then add the descaler according to the instructions on the packaging Step 5: Place a container of at least 1.5 liters under the spout, connect the milk tube to the spout, and immerse the other end in the container Step 6: The program runs automatically Step 7: After the first cycle, empty and rinse the tank, fill it with cold drinking water up to the MAX mark Step 8: Replace the tank and press the descaling button again to start the final rinse Step 9: Once finished, empty the grounds container if the light is flashing, then remove the extraction unit to eliminate any descaler residues Important: Only use descaling products approved for espresso machines. Regular descaling maintains your machine's performance and extends its lifespan.

Q: How to adjust the bitterness of coffee on the VALBERG PUMPGRINDER M1?

The VALBERG PUMPGRINDER M1 does not have a button specifically dedicated to bitterness. However, you can easily control the intensity and bitterness of the coffee by using the grind adjustment button (③). Grind adjustment: For 1 cup: positions 13-15 (default) For 2 cups: positions 11-13 (default) This button offers 31 different positions to adjust the fineness of the grind: Finer positions (lower numbers) = more bitter and intense coffee Coarser positions (higher numbers) = milder and less bitter coffee Start with the recommended positions based on the number of cups, then gradually adjust according to your personal preference.

Q: What is the spout of the VALBERG AUTOCOFFEE M3 coffee machine?

The spout of your VALBERG AUTOCOFFEE M3 coffee machine is the component through which the prepared beverages (coffee, espresso, hot water, cappuccino, latte macchiato, milk foam) flow. It is a key part of the distribution system located at the front of the machine. Main features of the spout: Removable and disassemblable into two parts (upper and lower half) for complete and easy cleaning Equipped with an integrated status indicator that shows you the operating status of the distribution system Height adjustable: you can slide it up or down to adapt the spacing according to the size of your cup or for a tall travel glass Covered with a removable lid for protection Important regarding safety: The spout becomes very hot during use and remains hot for some time afterward. Never touch it with bare hands to adjust or clean it. Always use a dry, clean cloth to handle it to avoid burns. Maintenance of the spout: After each use with milk or milk foam, clean it regularly. For a complete cleaning, remove the lid by pressing on both sides, open the metal support, separate the two halves of the spout, and clean them under running water. Dry them completely before reassembling by aligning and pressing them firmly together.

Question 1

The touchscreen remains black while the machine is on

Accepted Answer

The touchscreen of the control panel remains black while the machine is powered on.

The PDF of this manual does not explicitly mention this behavior. However, here is what we know about the normal operation of your VALBERG AUTOCOFFEE M3:

Normal Display

According to the manual, when powered on, the machine initiates a rinse cycle (70 to 80 seconds), then all beverage icons light up when it is ready. The touch buttons (Espresso, Coffee, Long Coffee, Cappuccino, Latte Macchiato, Milk Foam, Hot Water) should be visible and functional.

Possible Diagnostics

Frozen or malfunctioning touchscreen - If the screen remains black despite being powered on and after waiting more than 80 seconds, the touchscreen itself may be faulty. Try turning the device off and on again (Power button) and wait 2-3 minutes.
Contrast or brightness - Some machines have contrast settings. Check if there is an adjustment button that may have lowered the contrast to zero.
Extended sleep mode - If the machine has not been used for a long time, it may be in energy-saving mode. Press the Power button or any touch button.

If the screen remains black even after these checks, it is likely a defect in the touchscreen requiring repair.

Question 2

My VALBERG AUTOCOFFEE M3 coffee machine starts up by itself after a program - is this normal?

Accepted Answer

This is completely normal. The VALBERG AUTOCOFFEE M3 coffee machine is programmed to automatically restart certain cycles after the end of a program.

Here’s what happens:

After a cleaning or descaling cycle: the machine automatically returns to the main menu and may restart a rinsing cycle (70 to 80 seconds) before being ready.
Automatic rinsing cycle: after turning on, the device automatically starts a rinsing of 70 to 80 seconds before offering you the menu.
Reinsertion of the water tank: if you have just reinserted the tank, the machine pumps water into the internal tubes for 5 to 6 seconds, which may resemble a restart.

These behaviors are safety and hygiene features: they ensure that the machine is always rinsed and ready to operate correctly.

If the machine restarts abnormally outside of these cases (multiple times in a row without your action, or at the moment you want to turn it off), check that the water tank is properly in place and fully inserted, or consult the troubleshooting section of your manual.

Question 3

I don't have a cleaning tablet for my VALBERG AUTOCOFFEE M3: what should I do?

Accepted Answer

This is a common situation: cleaning tablets are not provided with your VALBERG AUTOCOFFEE M3. You need to obtain them separately.

What you need to know about the cleaning program:

The program lasts 20 minutes
You need to place a cleaning tablet in the ground coffee compartment
The indicators light up to signal the steps (emptying the tray, filling the tank)
Place a container of at least 1.5 liters under the spout before starting the program

Where to buy the tablets?
You can find them from spare parts dealers (Spareka, Eurosav) or on general websites (Amazon, ManoMano). Just search for "espresso machine cleaning tablets" - they are inexpensive.

If you don't have one right now, you can simply ignore this program for now and use it later when you have a tablet.

Question 4

Water remains stuck after filling the tank of my VALBERG AUTOCOFFEE M3: what should I do?

Accepted Answer

If a drop of water remains stuck after filling the tank of your VALBERG AUTOCOFFEE M3, here are the solutions:

1. Let the pump run

After reinserting the tank, the coffee machine will immediately start pumping water into the internal tubes for 5 to 6 seconds. This pressurization phase allows the water to circulate and any residues to flow out naturally. Wait for this cycle to complete fully before continuing.

2. Check the magnetic float

If the water refuses to leave, the magnetic float in the tank may be stuck or clogged. This blocks internal circulation. To resolve the issue:

Remove the water tank from the machine
Clean it thoroughly with warm water, especially around the float
Ensure that the float moves freely and is not stuck at the bottom
Reinsert the tank correctly

3. If the problem persists

If the water continues to remain stuck and the float is not the issue, this may indicate a blockage in the internal tubes or a malfunction of the pump. In this case, contact VALBERG customer service.

Question 5

How to descale the VALBERG AUTOCOFFEE M3 coffee machine?

Accepted Answer

Duration and Preparation

The complete program lasts 40 minutes. You will need a descaler for espresso machines (not provided with the device). Never use pure citric acid, vinegar, or vinegar-based products.

Step-by-Step Procedure

Step 1: Remove the milk tube and clean it
Step 2: Press and hold the descaling button for 3 seconds to start the program
Step 3: When the grounds container light flashes, empty the drip tray and the grounds container, then put them back in place
Step 4: Fill the water tank with 1 liter of lukewarm water, then add the descaler according to the instructions on the packaging
Step 5: Place a container of at least 1.5 liters under the spout, connect the milk tube to the spout, and immerse the other end in the container
Step 6: The program runs automatically
Step 7: After the first cycle, empty and rinse the tank, fill it with cold drinking water up to the MAX mark
Step 8: Replace the tank and press the descaling button again to start the final rinse
Step 9: Once finished, empty the grounds container if the light is flashing, then remove the extraction unit to eliminate any descaler residues

Important: Only use descaling products approved for espresso machines. Regular descaling maintains your machine's performance and extends its lifespan.

Question 6

Why does the descaling and cleaning indicator stay on my VALBERG AUTOCOFFEE M3 coffee machine?

Accepted Answer

The descaling and cleaning indicator of the brewer may stay on for two distinct reasons, depending on the type of indicator:

Descaling Indicator

This indicator lights up gradually and indicates the level of internal soiling of the machine. Here’s what it means:

At 50%: Descaling is recommended but optional. You can still use the machine.
At 100%: Descaling becomes mandatory. The machine will not operate until you have started the descaling program.

To turn it off, you need to press the "Descale" button for 3 seconds and start the full program (40 minutes). You will need to fill the tank with 1 liter of warm water + descaler for espresso machines (not provided with the device). The indicator will automatically reset at the end of the cycle.

Extraction System Cleaning Indicator

A second indicator manages the automatic cleaning of the extraction system. Press the corresponding button for 3 seconds to start the cleaning program (20 minutes). This program requires an espresso cleaning tablet (not provided). The indicator will turn off automatically after completion.

Important: Never use pure citric acid, vinegar, or any vinegar-based product to descale this machine - only a descaler suitable for espresso machines is allowed.

Question 7

What does the water indicator light flashing on my VALBERG AUTOCOFFEE M3 coffee machine mean?

Accepted Answer

If the water indicator light is flashing on your VALBERG AUTOCOFFEE M3, it generally means that the magnetic float in the tank is stuck, even if the tank appears to be full.

What to do:

Remove the water tank from the machine
Clean it thoroughly, especially around the float
Ensure that the magnetic float moves freely and floats unobstructed
Reinsert the tank correctly in position

After this operation, the light should stop flashing. If the problem persists after cleaning, the float or sensor may need to be replaced.

Question 8

How to adjust the bitterness of coffee on the VALBERG PUMPGRINDER M1?

Accepted Answer

The VALBERG PUMPGRINDER M1 does not have a button specifically dedicated to bitterness. However, you can easily control the intensity and bitterness of the coffee by using the grind adjustment button (③).

Grind adjustment:

For 1 cup: positions 13-15 (default)
For 2 cups: positions 11-13 (default)

This button offers 31 different positions to adjust the fineness of the grind:

Finer positions (lower numbers) = more bitter and intense coffee
Coarser positions (higher numbers) = milder and less bitter coffee

Start with the recommended positions based on the number of cups, then gradually adjust according to your personal preference.

Question 9

What is the tube that connects the milk reservoir to the spout of the VALBERG AUTOCOFFEE M3?

Accepted Answer

The component that connects the milk reservoir to the spout is called the milk tube. It is a removable pipe that ensures the connection between:

The milk container (capacity: 0.6 L max)
The spout of the machine

This tube includes a metal straw inserted into the lid of the container, which allows the system to suck the milk to prepare it according to your selection (cappuccino, latte, etc.). The milk tube is easily detachable for daily cleaning and maintenance.

Question 10

What is the spout of the VALBERG AUTOCOFFEE M3 coffee machine?

Accepted Answer

The spout of your VALBERG AUTOCOFFEE M3 coffee machine is the component through which the prepared beverages (coffee, espresso, hot water, cappuccino, latte macchiato, milk foam) flow. It is a key part of the distribution system located at the front of the machine.

Main features of the spout:

Removable and disassemblable into two parts (upper and lower half) for complete and easy cleaning
Equipped with an integrated status indicator that shows you the operating status of the distribution system
Height adjustable: you can slide it up or down to adapt the spacing according to the size of your cup or for a tall travel glass
Covered with a removable lid for protection

Important regarding safety: The spout becomes very hot during use and remains hot for some time afterward. Never touch it with bare hands to adjust or clean it. Always use a dry, clean cloth to handle it to avoid burns.

Maintenance of the spout: After each use with milk or milk foam, clean it regularly. For a complete cleaning, remove the lid by pressing on both sides, open the metal support, separate the two halves of the spout, and clean them under running water. Dry them completely before reassembling by aligning and pressing them firmly together.

User manual VALBERG Coffee machine : user manuals and guides in PDF

Models VALBERG Coffee machine most viewed

Other categories VALBERG

Recent questions about Coffee machine VALBERG