Q: What are the different operating modes of the VAL-MIST95 for?

The Mode button (button 6 on the control panel) allows you to select 4 distinct ventilation modes by pressing it repeatedly. A light indicator shows the currently active mode. Normal Mode - The fan operates at the speed you have chosen consistently and regularly. Natural Mode - The fan simulates a natural breeze by randomly varying the speed up to your maximum selection. Sleep Mode - The speed gradually decreases every 30 minutes until it becomes slow, perfect for sleeping hours. Smart Mode (AI) - The system automatically selects an appropriate speed based on the ambient temperature of the room, with no manual intervention required. This mode operates exclusively at medium speed. All these modes support oscillation, ionization, misting, and automatic timer functions (1h, 2h, 4h, or 8h).

Q: What does the drain plug of the VAL-MIST95 look like and how do I tighten it?

Appearance and location The drain plug of the VAL-MIST95 is identified by reference N in your manual. It is a drain plug with a spring clip , located under the water tank of the device. How to tighten it After closing the drain plug, ensure that it is well tightened to avoid water leaks. Here’s how to do it: Locate the plug under the tank Close it after draining by turning it gently until you feel slight resistance Make sure it is tight to prevent leaks during operation What is it for? This plug allows you to drain the residual water remaining in the device during regular cleaning of the tank or before long-term storage of your misting fan.

Q: Why does the water tank leak as soon as I click to install it?

If the tank leaks during installation , it is usually due to improper placement. Here’s how to fix the issue: Essential Checks Tank Installation - Make sure the 1-liter tank is properly engaged: tilt it slightly, insert the bottom first, then push upwards until you hear a clear click . The click confirms that the tank is securely locked. Tank Lid - Check that the top lid of the tank is properly closed by turning it clockwise until you feel slight resistance. Drain Plug (N) - Ensure that the drain plug located under the tank is tightly secured. This is often the source of side leaks or dripping. Wait Before Using - Once the tank is installed, wait 1 to 2 minutes before activating the misting. The system needs to fill and stabilize. If the leak persists after these checks, it is likely an internal sealing defect (seal or misting system). In this case, the tank or the device may require replacement or repair from VALBERG customer service.

Q: How to remove the blade cap from the VAL-MIST95?

Before any handling, unplug the device. To remove the blade cap (F) from the VAL-MIST95: Turn the blade cap clockwise to remove it from the motor shaft. You will also need to remove the grid nut (H) by turning it counterclockwise . To install the blades (G): Insert the blades onto the motor shaft, aligning the 2 center slots with the 2 pins on the shaft . Push the blades firmly until they are securely in place. Reattach the blade cap (F) by turning it counterclockwise until it is tight.

Q: Can the temperature be adjusted or controlled with the VAL-MIST95?

No, the VALBERG VAL-MIST95 does not allow for temperature adjustment or control . The device simply displays the ambient temperature of the room on its LCD screen, for informational purposes only. However, the device features an Intelligent Mode (AI) that automatically adjusts the fan speed based on the detected ambient temperature. When you press the AI Mode button (button 4), the fan selects the appropriate speed (low, medium, or high) according to the thermal conditions of the room. You cannot manually change this setting. The only settings available on the VAL-MIST95 are: The fan speed (low, medium, high) via the +/- buttons (10, 11) The operating modes : Normal, Natural, Sleep, or Intelligent (Mode button 6) The mist function (button 8) to humidify the air The ionization (button 5) to purify the air The oscillation (button 3) for side sweeping A timer (button 9): 1h, 2h, 4h, or 8h

Question 1

What is the water tank capacity of the VAL-MIST95?

Accepted Answer

The water tank of the VALBERG VAL-MIST95 humidifier has a capacity of approximately 1 liter.

The tank is removed from the back of the device and has a cap that opens by turning it counterclockwise. Wait 1 to 2 minutes after installation before activating the misting function to allow the system to fill properly.

Question 2

I didn't receive the manual, how do I assemble the VAL-MIST95?

Accepted Answer

No worries! Here are the essential steps to assemble your VAL-MIST95 misting fan.

Preparation

Before you begin, make sure you have a Phillips screwdriver and that the device is unplugged.

Assembly of the tube and base

Insert the tube (K) with the integrated cable into the main part by aligning the fixing hole with the adjustment knob (L), then tighten.
Insert the four wheels (P) into the holes located under the base (O).
Lay the device on its side and secure the base with three M5×20 bolts and washers (Q) by turning them clockwise.

Assembly of the motor and blade

Remove the blade cover (F) and the grille nut (H) from the motor shaft.
Align and secure the rear grille (I) by tightening it clockwise.
Insert the blade assembly (G) by aligning the slots with the pins.
Reattach the cover (F) by turning it counterclockwise.

Installation of the misting system and front grille

Connect the corrugated tube (A) to the misting cover (B) by twisting and pushing.
Attach the misting cover (B) to the front grille (C) with three ST3×7.5 screws (D) by turning them clockwise.
Align the front and rear grilles, push together until the rear grille clicks into place.
Connect the other end of the tube to the misting outlet (R).

Installation of the water tank

Unplug the device.
Remove the tank (M) from the back of the device.
Open the lid by turning it counterclockwise.
Fill with fresh tap water and securely close the lid.
Insert the tank at an angle, starting from the bottom, then push up until you hear a click.
Wait 1-2 minutes before using the misting function.

Important: Place your VAL-MIST95 on a stable, dry, and level surface before using it.

Question 3

What are the different operating modes of the VAL-MIST95 for?

Accepted Answer

The Mode button (button 6 on the control panel) allows you to select 4 distinct ventilation modes by pressing it repeatedly. A light indicator shows the currently active mode.

Normal Mode - The fan operates at the speed you have chosen consistently and regularly.
Natural Mode - The fan simulates a natural breeze by randomly varying the speed up to your maximum selection.
Sleep Mode - The speed gradually decreases every 30 minutes until it becomes slow, perfect for sleeping hours.
Smart Mode (AI) - The system automatically selects an appropriate speed based on the ambient temperature of the room, with no manual intervention required. This mode operates exclusively at medium speed.

All these modes support oscillation, ionization, misting, and automatic timer functions (1h, 2h, 4h, or 8h).

Question 4

How to assemble and mount the VAL-MIST95?

Accepted Answer

The assembly of the VAL-MIST95 follows a specific order in 11 main steps:

Tube and cable - Insert the tube (K) into the main part aligning with the fixing knob (L), then tighten.
Wheels - Push the 4 wheels (P) into the holes on the underside of the base (O).
Base attachment - Lay the device on its side, align the base (O) and secure with 3 sets of M5*20 bolts and washers by turning clockwise.
Motor preparation - Remove the blade cap (F) and the grid nut (H) from the motor shaft.
Rear grid - Align and secure the rear grid (I) with the grid nut by turning clockwise.
Blades - Insert the blades (G) by aligning the slots with the pins, then push in.
Blade cap - Screw on the cap (F) by turning counterclockwise.
Fogging pipe - Connect the corrugated pipe (A) to the fogging cover (B).
Front grid - Attach the fogging cover (B) to the front grid (C) with 3 ST3*7.5 screws by turning clockwise.
Final assembly of grids - Align the front grid and ring (C+E) with the rear grid (I), push until you hear a click confirming the lock.
Finishing the pipe - Connect the other end of the corrugated pipe (A) to the fogging outlet (R).

Required tools: a cross screwdriver.

Important: Always unplug the device before assembly or disassembly to avoid the risk of electric shock.

After assembly, place the device on a dry, flat, and stable surface, fill the water tank with fresh water, and then plug in the power cord.

Question 5

How to remove the motor shaft from the VAL-MIST95 if it is stuck or jammed?

Accepted Answer

According to the VAL-MIST95 manual, here’s how to proceed to remove the motor shaft:

Removal Steps:

Blade Cap (F): turn it counterclockwise
Grid Nut (H): turn it counterclockwise
Once these elements are removed, you can access the motor shaft

If the shaft is stuck:

If you encounter strong resistance, do not force it. First, ensure that the device is unplugged from the power outlet.

The shaft may be stuck due to limescale or mineral deposits. You can:

Soak the metal parts in white vinegar for 30 minutes to dissolve the limescale
Use a small wrench or suitable tool to grip the nut better and turn it gradually
Make gentle back-and-forth movements instead of applying force all at once

After cleaning, you can reverse the assembly steps described in the manual to reassemble the device.

Question 6

What does the drain plug of the VAL-MIST95 look like and how do I tighten it?

Accepted Answer

Appearance and location

The drain plug of the VAL-MIST95 is identified by reference N in your manual. It is a drain plug with a spring clip, located under the water tank of the device.

How to tighten it

After closing the drain plug, ensure that it is well tightened to avoid water leaks. Here’s how to do it:

Locate the plug under the tank
Close it after draining by turning it gently until you feel slight resistance
Make sure it is tight to prevent leaks during operation

What is it for?

This plug allows you to drain the residual water remaining in the device during regular cleaning of the tank or before long-term storage of your misting fan.

Question 7

Why does the water tank leak as soon as I click to install it?

Accepted Answer

If the tank leaks during installation, it is usually due to improper placement. Here’s how to fix the issue:

Essential Checks

Tank Installation - Make sure the 1-liter tank is properly engaged: tilt it slightly, insert the bottom first, then push upwards until you hear a clear click. The click confirms that the tank is securely locked.
Tank Lid - Check that the top lid of the tank is properly closed by turning it clockwise until you feel slight resistance.
Drain Plug (N) - Ensure that the drain plug located under the tank is tightly secured. This is often the source of side leaks or dripping.
Wait Before Using - Once the tank is installed, wait 1 to 2 minutes before activating the misting. The system needs to fill and stabilize.

If the leak persists after these checks, it is likely an internal sealing defect (seal or misting system). In this case, the tank or the device may require replacement or repair from VALBERG customer service.

Question 8

What does the flashing misting button on the VAL-MIST95 mean?

Accepted Answer

The flashing misting button (indicator 22) means that the water tank is empty or that the water level is too low. The device will automatically turn off after flashing 10 times.

How to resolve the issue

Immediately turn off the misting fan
Gently unscrew the water tank to remove it
Fill it completely with fresh tap water
Reinstall the tank until you hear a locking click
Wait 1 to 2 minutes before reactivating the misting - the system needs this time to fill properly

If the button flashes again after filling the tank, check that it is securely attached and that no leaks are occurring during installation.

Question 9

How to remove the blade cap from the VAL-MIST95?

Accepted Answer

Before any handling, unplug the device.

To remove the blade cap (F) from the VAL-MIST95:

Turn the blade cap clockwise to remove it from the motor shaft.
You will also need to remove the grid nut (H) by turning it counterclockwise.

To install the blades (G):

Insert the blades onto the motor shaft, aligning the 2 center slots with the 2 pins on the shaft.
Push the blades firmly until they are securely in place.
Reattach the blade cap (F) by turning it counterclockwise until it is tight.

Question 10

Can the temperature be adjusted or controlled with the VAL-MIST95?

Accepted Answer

No, the VALBERG VAL-MIST95 does not allow for temperature adjustment or control. The device simply displays the ambient temperature of the room on its LCD screen, for informational purposes only.

However, the device features an Intelligent Mode (AI) that automatically adjusts the fan speed based on the detected ambient temperature. When you press the AI Mode button (button 4), the fan selects the appropriate speed (low, medium, or high) according to the thermal conditions of the room. You cannot manually change this setting.

The only settings available on the VAL-MIST95 are:

The fan speed (low, medium, high) via the +/- buttons (10, 11)
The operating modes: Normal, Natural, Sleep, or Intelligent (Mode button 6)
The mist function (button 8) to humidify the air
The ionization (button 5) to purify the air
The oscillation (button 3) for side sweeping
A timer (button 9): 1h, 2h, 4h, or 8h

User manual VALBERG Misting fan : user manuals and guides in PDF

Models VALBERG Misting fan most viewed

Other categories VALBERG

Recent questions about Misting fan VALBERG