VAL-MIST95 - Misting fan VALBERG - Free user manual and instructions

Product type	Pedestal misting fan
Brand	VALBERG
Model	VAL-MIST95 (985830)
Dimensions (L x D x H)	46 x 38 x 132 cm
Weight	Approximately 6 kg
Power supply	220-240 V ~ 50 Hz
Rated power	95 W
Power consumption (ventilation)	44.2 W
Standby consumption	0.22 W
Protection class	II
Power cord length	183 cm
Maximum air flow	60.65 m³/min
Sound power level	62.88 dB(A)
Maximum air speed	3.39 m/s
Service value (SV)	1.37 (m³/min)/W
Seasonal electricity consumption	14.39 kWh/year
Main functions	Misting, ionization, oscillation, 3 speeds, Normal/Nature/Sleep/Smart modes, timer 1h/2h/4h/8h
Remote control	Yes (AAA/R03 batteries not included)
Water tank capacity	Approximately 1 L (estimate)
Spare parts and repairability	Grilles, blades, tank, corrugated tube, casters, screws; disassembly possible for cleaning
Maintenance and cleaning	Unplug before cleaning; grilles and blades washable with soapy water; tank rinsed regularly
Warranty	2 years (upon presentation of receipt)

Frequently Asked Questions - VAL-MIST95 VALBERG

How to assemble the VAL-MIST95 misting fan?

Follow the assembly steps in the manual: attach the tube, casters, base, rear grille, blades, front grille, and misting unit. Use a Phillips screwdriver. Unplug the appliance before any handling.

How to fill the water tank?

Turn off the appliance, remove the tank from the back, open the cap by turning counterclockwise, fill with fresh tap water, close and replace the tank by tilting it until it clicks. Wait 1 to 2 minutes before using the misting function.

What to do if the misting indicator flashes 10 times?

This means the water tank is empty or the level is too low. Turn off the appliance, remove the tank and fill it with water.

How to use the remote control?

Insert 2 AAA/R03 batteries (not included) into the remote control respecting polarity. The remote control allows you to control speed, oscillation, misting, timer, and ventilation modes.

What are the available ventilation modes?

The modes are: Normal (constant speed), Nature (simulates a natural breeze), Sleep (speed gradually decreases), and Smart (automatically adjusts speed according to ambient temperature).

How to set the auto-off timer?

Press the Timer button (9) repeatedly to select 1h, 2h, 4h, or 8h. The corresponding indicator lights up. To cancel, press until all options have cycled.

How to clean the misting fan?

Unplug the appliance. Remove the tank, empty it and rinse it. Clean the motor unit, base, and compartment with a slightly damp soft cloth. The grilles and blades can be washed with soapy water after disassembly. Dry thoroughly before reassembling.

Can we use misting without the fan running?

Yes, the misting function can be activated even when the fan is off. The misting indicator then lights up.

What to do in case of water leakage?

Check that the water tank is correctly installed (clicked in) and that the caps are properly closed. Make sure the drain plug (N) is tightly closed. If the leak persists, contact customer service.

How to store the appliance when not in use?

Unplug it, empty and dry the tank, clean the grilles and blades, then disassemble if necessary by reversing the assembly steps. Store in a cool, dry place away from dust.

USER MANUAL VAL-MIST95 VALBERG

This product is guaranteed against faults caused by defects in manufacturing or the materials used for a period of two years, starting from the date of purchase.* This warranty does not cover defects or damage caused by failure to install the device correctly, incorrect use of the product, or excessive wear and tear.

*proof of purchase required

WARRANTY CONDITIONS

FR

Thank you for choosing this VALBERG product. VALBERG products are chosen, tested, and recommended by ELECTRO DEPOT, so you can be sure you are getting a top-quality, easy-to-use product that won't let you down.

We're confident your new device will be a pleasure to use every day!

Welcome to ELECTRO DEPOT.

Table of Contents

Parts

Product overview

Intended use

Specifications

Assembly

Filling the water tank

Installing the remote control battery

Use

Cleaning and maintenance

Storage

Parts

A Corrugated hose, B Misting cap, C Front grille, D Screws (ST3*7.5) x 3, E Grille retaining ring, F Blade cap, G 6 Blades, H Grille nut, I Back grille, J Motor unit, K Pole, L Pole fastening knob, M Water tank, N Drain plug with spring clamp, O Base, P Caster x 4

Q Bolt and washer (M5*20) x 3, R Mist outlet, S Control panel: 1 Power indicator light, 2 Room temperature display, 3 Oscillation button, 4 AI Mode button, 5 Ion button, 6 Mode button, 7 On/Off button, 8 Mist button, 9 Auto-off Timer button, 10 Speed - button, 11 Speed + button, 12 Auto-off Timer indicator light, 13 Oscillation indicator light, 14 Low speed indicator light

A Product overview

15 Medium speed indicator light, 16 High speed indicator light, 17 AI Mode indicator light, 18 Ion indicator light, 19 Normal Mode indicator light, 20 Natural Mode indicator light, 21 Sleep Mode indicator light, 22 Mist indicator light. Remote control: 1 Speed button, 2 Oscillation button, 3 Mist button, 4 On/Off button, 5 Timer button, 6 Mode button

Product overview

• Unpack and remove all labels from the unit except the nameplate. Please check that all parts are included and intact. If the unit is damaged or faulty, do not use it and take it to your retailer or after-sales service centre.
• Keep all packaging out of the reach of children. There is a risk of accidents if children play with packaging materials.

Intended use

This unit is intended for household use only and not for commercial, industrial, or outdoor use. The unit has been designed for indoor use to circulate air, generate airflow, and produce mist. Use the unit in a room with dry conditions and adequate ventilation. Any other use may damage the unit or cause injury.

Specifications

Model:	985830
Stand fan
Operating voltage:	220-240V~, 50 Hz
Rated power:	95 W
Protection class:	Class II
Power cable (L):	183 cm
Dimensions (W x D x H):	46 x 38 x 132 cm
Remote control
Battery type:	2x AAA/R03 battery (not included)

Information requirements for comfort fans according to Regulation (EU) N°206/2012

Model identification		985830
Description	Symbol	Value	Unit
Maximum fan flow rate	F	60.65	m³/min
Fan power input	P	44.2	W
Service value	SV	1.37	(m³/min)/W
Standby power consumption	PSB	0.22	W

A Product overview

Seasonal electricity consumption	Q	14.39	kWh/a
Fan sound power level	LWA	62.88	dB(A)
Maximum air velocity	c	3.39	meters/sec
Measurement standard for service value	(EU) No 206/2012 + (EU) No 2016/2282
Contact details for obtaining more information	Electro Dépôt - 1 route de Vendeville F-59155 FACHES THUMESNIL - France

Assembly

WARNING!

Before assembling or disassembling the unit, always disconnect the unit from the mains supply to avoid the risk of injury.

Tool required: Cross-head screwdriver.

1. Insert the pole (K) and integrated cable into the body unit by aligning the fastening hole with the fastening knob (L), then tighten the knob.
2. To attach the casters (P), push the casters into the 4 holes on the underside of the base (O).
3. Carefully lay the main unit on its side on a raised surface. Align the base (O) with the bottom of the main unit, and secure the base with the 3 bolts and washers (M5*20) (Q) provided, turning the bolts clockwise.
4. Remove the blade cap (F) and grille nut (H) from the motor shaft by turning them clockwise and anti-clockwise respectively.
5. Align the rear grill (I) with the front of the motor unit (J) and secure it with the grille nut (H) by turning the nut clockwise.
6. Insert the blades (G) into the motor shaft by aligning the 2 slots in the center with the 2 pins on the shaft, then push the blades in.
7. Tighten the blade cap (F) onto the motor shaft by turning it anti-clockwise.
8. Connect the corrugated hose (A) to the misting cap (B) by twisting and pushing it in.
9. Place the misting cap (B) on the front of the front grille (C) by aligning the 3 screw holes, and secure it with the 3 screws (ST3*7.5) (D) by turning them clockwise.
10. Align the front grille and retaining ring (C + E) assembly with the back grille (I) and push until the back grille snaps into the groove of the retaining ring on all sides. Lightly tighten the screw on the retaining ring if needed. Make sure the grilles are securely locked.
11. Connect the other end of the corrugated hose (A) to the mist outlet (R).

Filling the water tank

Fill the water tank to use the mist function:

1. Press the On/Off button (7) to turn off the unit.
2. Remove the water tank (M) from the back of the main unit.
3. Open the cap by turning anti-clockwise, fill the water tank with fresh room temperature tap water, and close the cap tightly.
4. Insert the water tank into the compartment at an angle, inserting the bottom of the tank first, then push the top in until the tank clicks into place. Make sure the water tank is properly inserted to avoid leaks.
5. Wait 1 to 2 minutes to allow the water to fill the mist chamber.

B Product usage

NOTE: Turn off the unit and refill the water tank when the Mist indicator light (22) flashes 10 times and turns off. This indicates that water tank is empty or the water level is too low.

Installing the remote control battery

1. Slide out the battery cover on the remote control.
2. Insert the new batteries [AAA/R03 x 2, not included] following the "+" and "-" ends indicated inside the battery compartment.
3. Dispose of used batteries safely.
4. Close the cover.

Use

The fan can be controlled using the control panel or the remote control.

1. Place the unit on a dry, level and stable surface.
2. Make sure the unit is properly assembled.
3. Fill the water tank if required.
4. Plug the power cable into a suitable mains socket. The power indicator light (1) will turn on to indicate the unit is connected to the power supply.
5. Press the On/Off button (7) to turn the fan on or off. The fan starts running at Low speed (default) and the display shows the room temperature.
6. Press the Speed +/- button (11/10) to set the desired speed (Low/Medium/High).
7. Press the Mode button (6) to select the desired wind mode:
8. Normal Mode (19) - The fan operates at the selected speed.
9. Natural Mode (20) - The fan simulates natural breezes by alternating the speed in random patterns, with the selected speed set as the highest speed.
10. Sleep Mode (21) - The fan speed decreases every 30 minutes until reaching Low speed.

Mode	Speed	Oscillation	Ion	Mist1	Auto-off timer 1h/2h/4h/8h
Normal Mode	1/2/3	✓	✓	✓	✓
Natural Mode	1/2/3	✓	✓	✓	✓
Sleep Mode	1/2/3	✓	✓	✓	✓
AI Mode2	2	✓	✓	✓	✓
Off	-	-	-	✓	-

1 The Mist function is available in any mode and can be used when the fan is turned off. 2 After turning off AI Mode, the fan will exit to Normal Mode at Low speed.

B Product usage

1. Press the Mist button (8) to turn on or off the mist (humidification) function. The mist indicator light (22) will turn on when the function is activated. This function can be used on hot and dry days to help humidify and cool the room environment.
2. Press the Ion button (5) to turn on or off the ion function to release negative ions into the air.
3. Press the Timer button (9) to set an Auto-off timer (1h / 2h / 4h / 8h). Observe the indicator light of the timer setting selected (12). To cancel a timer, press the Timer button repeatedly until cycling out the timer options.
4. Press the AI button (4) to turn AI Mode on or off. When the mode is activated, the fan will automatically select a suitable speed level according to the current room temperature.
5. Turn off the fan after each use. Unplug the fan from the mains socket before leaving it unattended, or if it is not going to be used for a long period of time.

Cleaning and maintenance

WARNING! To avoid the risk of injury, electric shock or fire:

• Always turn off and unplug the unit from the mains socket before cleaning, assembling, or disassembling the unit.
• Never immerse the unit, power cable or plug in water or any liquid. Do not rinse the unit under the tap.
• Never use solvents (gasoline, benzene, thinner, etc.), chemical or abrasive cleaning agents, wire brushes, sharp objects or scouring pads to clean the unit.
• Keep the grilles and air vents on the back of the motor unit free from dust or dirt.
• Remove the water tank, empty the tank and rinse it out thoroughly. Allow the interior of the tank to air dry completely before closing the cap if the unit will be stored for a prolonged period.
• Remove the drain plug with spring clamp (N) to empty any remaining water inside the unit. Close the drain plug with spring clamp.
• Clean the motor unit, main body, water tank compartment, and base unit with a soft cloth slightly moistened with water or soapy water. Dry completely with a soft, dry cloth. Do not allow water or any liquid to enter the motor unit or main unit during cleaning.
• For a quick cleaning, you can use a vacuum cleaner to clean the grilles and air vents.
• For a thorough cleaning:
• Remove the grilles and fan blades for cleaning by reversing the steps in the "Assembly" section.
• Clean the grilles and fan blades in soapy water with a soft sponge. Rinse and dry thoroughly before reassembling them into the unit.

Storage

• Always unplug the unit before storing it.
• Store the unit in a fresh, dry and dust-free place, out of the reach of children and pets.
• Please retain the packaging and use it to store your unit when it is not in use for an extended period of time.
• To disassemble the unit for storage, reverse the steps in the "Assembly" section.

Thank you!