BOH-1050-1 - Drill MSW - Free user manual and instructions

USER MANUAL BOH-1050-1 MSW

Yellow and black electric drill bit with labeled parts (no text or symbols on body)

Operation manual must be reviewed.

Never dispose of electrical equipment together with household waste.

CE This machine conforms to CE declarations.

Safety goggles must be used.

Ear protection must be used.

Safety mask must be used.

Protective footwear must be used.

II protection class machine with double insulation.

Attention! Wear protective gloves.

PLEASE NOTE! Drawings in this manual are for illustration purposes only and in some details may differ from the actual machine.

The original operation manual is in German. Other language versions are translations from German.

SAFETY INSTRUCTIONS

1. Keep work area clean. Cluttered areas can cause injuries.

2. Consider the work area environment before starting to work. Don't expose power tools to rain or wet soil. Don't use power tools in damp or wet locations. The work area should be well secured. Don't use the tool in the presence of flammable liquids or gases. Power tools produce sparks during normal operation or when switching ON/OFF. Never use power tools in dangerous sites containing lacquer, paint, benzene, thinner, gasoline, gases, adhesive agents, and other materials which are combustible or explosive.

3. Provide sufficient protection against electric shock. Prevent body contact with grounded surfaces. For example: pipes, radiators, ranges, refrigerator enclosures.

4. Keep children and third parties away from work area.

5. Store unused tools. When not in use, tools should be stored in dry and high or locked-up place out of reach of children.

6. Do not overload the machine! To ensure an optimum in the performance and safety of the machine, only use it within the set parameters.

7. Use only suitable tools. Don't use small tools or attachments. Don't use tool for not intended purposes. For example: don't use circular saw for cutting tree limbs or logs.

8. Dress properly. Do not wear loose clothing or jewellery. They can get caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair.

9. Use safety glasses. Also use face or dust mask if the cutting operation is dusty.

10. Do not damage the connection cable. Never carry the tool by the cord or yank the cord to disconnect it from the power source. Keep cord from heat and oil sources and sharp edges.

11. Secure work area. It is recommended to use clamps or a vice for fixation. Please pay special attention to your hands when operating the machine!

12. Do not overreach yourself. Keep proper footing and balance at all times.

13. Hold the machine firmly in both hands. When using the machine, hold it by the handles provided with the machine.

1. Maintain tools with care. Keep tools clean for better and safer performance. Follow instructions for changing accessories. Inspect extension cords periodically and replace if damaged. Keep hand les dry, clean, and free from oil and grease.

2. Switch off the machine and disconnect the cable before performing maintenance or changing accessories.

3. Remove adjusting keys and wrenches. Always make sure that keys and adjusting wrenches are removed from the tool before turning it on.

4. Avoid unintentional starting. Don't carry plugged-in tool with finger on switch. Be sure the tool is switched off when plugging it in.

5. During outdoor work use extension cords intended for outdoor use.

6. Stay alert when operating the machine. Do not operate tool when you are tired.

7. Check damaged parts. Before further use of the tool, any part of the casing or other parts that are damaged should be carefully checked to determine that they will operate properly and perform their intended function. Check for alignment of moving parts, mounting, and any other conditions that may affect its operation. A part that is damaged should be properly repaired or replaced by an authorized service centre unless otherwise indicated elsewhere in this

Instruction manual. Defective switches should be replaced by an authorized service centre. Do not use the tool if the switch does not turn it on and off.

1. Do not use power tools for applications other than those specified in the instructions (other than that for which it was designed).

2. To ensure the designed operational integrity of power tools, do not remove installed covers or screws.

3. Do not touch movable parts or accessories unless the power source has been disconnected.

4. Use your tool at lower input load than specified on the nameplate to increase working efficiency and decrease wear out.

5. Do not wipe plastic parts with solvent. Solvents such as gasoline, thinner, benzene, alcohol,

ammonia and oil may damage and crack plastic parts. Do not wipe them with such solvents. Wipe plastic parts with a soft cloth lightly dampened with soapy water.

1. Consult an authorized service agent in the event of power tool failure.

2. Use only original replacement parts.

3. This tool should only be disassembled for replacement of carbon brushes.

4. Hold the rotary hammer by the insulated surface of the handles as it is possible that hidden electric wires or the device's own power cord may be struck during work with the machine. Contact with an electric wire of a power network may cause electrocution.

PRECAUTIONS ON USING THE MACHINE

1. Wear protective glasses to protect your eyes.
2. Use dust masks.
3. Use earplugs to keep your ears noise-free while working.
4. Check for the proper adjustment of the handle.
5. The tool becomes very hot during operation.
6. Be sure to use the side handle.
7. Safe operation depends on one's work posture.
8. Before commencing work, the oil level and tightness of screws is to be checked.
9. When working in an elevated location, pay attention to objects and persons below.
10. Before you start breaking or chipping a wall, floor or ceiling, thoroughly confirm that no items such as an electric cable conduit or pipes are cached inside.
    II. Wear protective shoes to protect your feet.
11. To avoid injury from accidental starting, always remove the plug from the electrical socket before installing or removing a drill bit, saw blade, sandpaper, accessory or attachment.

1. When using a keyed or keyless chuck DO NOT install or use any drill bit that exceeds 7" (175 mm) in length or extends more than 6" (150 mm) beyond the chuck jaws. They can suddenly bend or break (for model BOH-1800-I).
2. Before starting use of the tool, lightly press the drill switch to make sure the drill bit does not wobble or vibrate.
3. Do not use fly cutters or multiple-part hole cutters, as they can come apart or become unbalanced in use.
4. Make sure that the spindle has come to a complete stop before touching the chuck or attempting to change the drill bit.
5. Always make sure that the chuck is tight and the drill is firmly tightened in the chuck before starting to drill.

Failure to follow safety recommendations and instructions may result in serious injuries or death!

TECHNICAL SPECIFICATIONS

Product name	Rotary Hammer
Model	BOH-1800-I
Rated voltage/frequency	230V / 50Hz
Weight (kg)	5,7
Power (W)	1800
Max. impact rates (BPM)	4000/min
Impact Joules (J)	7
No load speed (r/min)	0-900
Tool holder	SDS-Plus
Drilling diameter max. (mm):
Steel:	13
Concrete:	36
Wood:	42
Sound power level LwA	105dB(A), Uncertainty K=3,0dB(A)
Sound pressure level LpA	94dB(A), Uncertainty K=3,0dB(A)
Vibration emission value ah_CHeq	14,760 m/s2, Uncertainty K=1,5 m/s2
Vibration emission value ah_HD	19,190 m/s2, Uncertainty K=1,5 m/s2

Product name Rotary Hammer
Model BOH-1050-2 BOH-1050-1
Rated voltage/frequency 230~V / 50Hz 230~V / 50Hz
Weight (kg) 3,24
Power (W) 1050 1050
Max. impact rates (BPM) 4000/min	5200/min
Impact Joules (J) 4 2.8
No load speed (r/min) 850 1050
Tool holder	SDS-Plus	SDS-Plus
Drilling diameter max. (mm):Steel: Concrete: Wood:	132642	132642
Sound power level LwA	100,4dB(A Uncertainty K=3,0dB(A)	100,3dB(A), Uncertainty K=3,0dB(A)
Sound pressure level LpA	89,4dB(A), Uncertainty K=3,0dB(A)	89,3dB(A), Uncertainty K=3,0dB(A)
Vibration emission value ah_CHeq	14,898 m/s2, Uncertainty K=1,5 m/s2	19,200 m/s2, Uncertainty K=1,5 m/s2
Vibration emission value ah_HD	14,936 m/s2, Uncertainty K=1,5 m/s2	19,140 m/s2, Uncertainty K=1,5 m/s2

APPLICATIONS

This tool is intended for hammer drilling in concrete, brick and stone as well as for light chiseling work; for drilling in wood, metal and plastic.

BEFORE USE

1. Power source
   Ensure that the power source to be utilized conforms to the power requirements specified on the product name plate.
2. Grounding
   This tool should be grounded while in use to protect the operator from electric shock.
3. Power switch
   Ensure that the power switch is in the OFF position. If the plug is connected to a power receptacle while the power switch is in the ON position, serious accidents can occur.
4. Extension cord
   If the work area has no power source, use an extension cord of sufficient thickness and rated capacity. The extension cord should be kept as short as possible.

HOW TO USE

1. Inserting and removing parts

The tool holder is maintenance-free. The dust cap prevents drilling dust from entering the machine during operation.

Inserting tool:

Clean and lightly grease tool shank before inserting. Pull back fastening sleeve and hold. Twist the tool into the holder and push it in until it engages. In case of BOH-1050-1, twist the tool into the holder and push it in until it engages. It's not necessary to pull back the fastening sleeve. The tool shank locks in position automatically. Pull the tool to check if it is locked correctly.

Removing the tool:

Push back the locking sleeve of the tool holder and remove the tool.

1. Handle attachment

For reasons of safety, the rotary hammer should only be used with the handle attachment.

1. Dust cap

Before carrying out hammer or drilling works vertically overhead, the device should be equipped with the dust collecting cap.

1. BOH-1800-1

I - fastening sleeve

2 - cap for carbon brushes

3 - dust guard

4 - switch:

- drill: "rotation is on" - to work with drills

- manual adjustment of the tool: setting the tool in the desired work position

- hammer: "rotation is off" - to work with cutters / chisels (tool position can be locked or unlocked)

5 - rotor
6 - handle attachment
7 - ON/OFF switch
8 - stroke switch: "work with stroke" / "work without stroke"
9 - crankcase cover
10 - speed adjustment

1. BOH-1050-1

I - fastening sleeve
2 - cap for carbon brushes
3 - dust guard
4 – drill / hammer switch: "rotation is on" – to work with drills / "rotation is off" – hammering to work with cutters and chisels
5 - rotor
6 - handle attachment
7 - ON/OFF switch
8 - stroke switch: "work with stroke" / "work without stroke"
9 - crankcase cover

1. BOH-1050-2

Yellow and black electric drill put tool with numbered components (no text or symbols visible)

I - fastening sleeve
2 - cap for carbon brushes
3 - dust guard
4 - switch:

-drill
- hammer with drill
- flat chisel lock
- hammer

5 - motor

6 - handle attachment
7 - ON/OFF switch
8 - lock switch
9 - rotation direction (left, right)

1. Crankcase lubrication

The crankcase should be lubricated regularly. After approximately 20 working hours, check and refill grease in the crankcase.

REPLACING CARBON BRUSHES

When the device is operated carbon brushes wear out steadily. When the insulation tip integrated inside the brush gets revealed and touches the commutator it will trip the engine automatically. When this happens, both brushes must be replaced with new brushes of the same type.

Attention! Before commencing carbon brush replacement make sure the device is switched off and the power cord is unplugged.

To replace carbon brushes:

For the BOH-1050-2 | BOH-1800-1 model:

- Unscrew protection cover screws that secure carbon brushes using a screwdriver

• Remove worn out brushes
• Insert new brushes
• Put protection covers back in place and screw the assembly back together Model BOH-1050-1:
• Unscrew protection covers on both sides of the device using a screw driver
• Remove worn out brushes
• Insert new brushes
• Put protection covers back in place and screw the assembly back together

MAINTENANCE AND INSPECTION

1. Inspecting the tool

Since use of a dull tool will cause the motor to malfunction, it should be replaced with a new one without delay when abrasion is noticed.

1. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazard.

1. Maintenance of the motor

The motor unit winding is the very "heart" of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water.

1. Inspecting the carbon brushes

The motor employs carbon brushes which are consumable parts. When they become worn or near "wear limit", it could result in motor trouble. When an auto-stop carbon brush is equipped, the motor will stop automatically. At that time, replace both carbon brushes with new ones. In addition always keep carbon brushes clean and ensure that they slide freely within the brush holders.

1. Installing drills

Never hold the chuck body with one hand and use the drill power to rotate the drill body to loosen or tighten drills. You may severely injure your hand. Always check whether the drill is properly mounted in the chuck.

1. Drilling (concerning BOH-1800-I)

When drilling in smooth hard surfaces such as metal, use centre punch to mark the desired hole location. This will prevent the drill from slipping off centre as the hole is started. The workpiece should be secured in a vice or with clamps to keep it from turning as the drill rotates. Check drill to make sure it is firmly locked in the drill chuck.

1. Service

When making repairs, use only identical replacement parts. In such cases please contact our service centre. Use of any other part may create a hazard or cause product damage. Do not attempt to modify tools or use accessories which are not recommended. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious injury. It will also void the warranty.

1. Cleaning the device

To keep the device clean, clean it using a soft cloth damped in water with soap. Never use brushes or other cleaning tools that may scratch/damage the device. Remember to prevent water from penet rating the device through the vents in the housing of the device. Clean the vents with a paintbrush and compressed air.

TRANSPORTATION AND STORAGE

Shaking, crashing and turning upside down of the machine should be prevented when it is transported. Store it in a properly ventilated surrounding with dry air and without any corrosive gas.

REGULAR CONTROL OF DEVICE

Regularly check the machine for signs of damage. If it should be damaged, please stop using it immediately and contact your customer service to solve the problem.

What to do in case of a problem?

Please contact your customer service and prepare following information:

• Invoice number and serial number (the latter is to be found on the technical plate on the machine).

• If relevant, a picture of the damaged, broken or defective part.

- It will be easier for your customer service clerk to determine the source of the problem if you give

a detailed and precise description of the matter. The more detailed your information, the better

customer service will be able to solve your problem rapidly and efficiently!

CAUTION: Never open the machine without the authorization of your customer service. This can lead to a loss of warranty!

INSTRUKCJA OBSŁUGI

SYMBOLE

Push back the locking sleeve of the tool holder and remove the tool.

Yellow and black electric drill bit with numbered components (no text or symbols visible)

Yellow and black electric drill put tool with labeled parts (no text or symbols visible)

Yellow and black power drill with labeled components (no text or symbols visible)

Yellow and black photo of a yellow drill bit with labeled parts (no text or symbols visible)

Yellow and black electric drill put tool with labeled parts (no text or symbols on body)

Labeled diagram of a yellow and black drill bit with numbered parts for identification

Yellow and black drill bit with numbered components (no visible text or symbols)

Diese Erkreibung besteht sich nur auf die Maschine im Zustand, in dem sie auf den Markt eingeführt wurde und schließlich keine Komponenten, die vom Endverbraucher hinaugefügt wurden und keine vom Endverbraucher durchgeführtes Tätigkeiten/Umbaubarbeiten, ein. Die technische Dokumentation befindet sich im Hirnensitz von EXPONDO Polska sp. z o.o. sp. k., und über ihre Verfügbankelt entscheidet die dazu befragte Person Plotr R. Gajas. I) This declaration relates exclusively to the product in the state in which it was placed on the market. Any components added, handling effected on modifications carried out subsequently are exclusively exposed. The technical documentation can be obtained at the time of publication. In addition, we will not only be made for any other component of the products or their own products or its own products or its own products or its own products or its own products or its own products or its own products or its own products or its own products or its own products or its own products or its own products or its own products or its own products or its own products or its own products or its own products or its own products or its own products or its own products or its own products or its own products or its own products or its own products or its own products or its own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or its own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or his own products or its own products nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own product nor their own

Dr, Duwur / Place, Date / Kuyer, Date / Lieu, Date / Luqay, Date /Luyer, Fexiu (Ms 18, Durnm

Unterschrift / Signature / Post-/- Signature / Areso / Fina. / Post-

Piotr R. Gajos

For the disposal of the device please consider and act according to the national and local rules and regulations.

CONTACT

expondo Polska sp. z o.o. sp. k.