TC-AV 2032 DW - Vacuum Cleaner EINHELL - Free user manual and instructions

USER MANUAL TC-AV 2032 DW EINHELL

GB Original operating instructions Ash vacuum

When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.

Explanation of the symbols used (see Fig. 10)

1. Danger! - Read the operating instructions to reduce the risk of injury.

2. Danger! Wait at least 24 hours before vacuuming an oven or a fi replace in order to be sure that the fi re has gone out and the ash has cooled down. Only for cold ash, see the operating instructions!

3. WARNING: Fire hazard

• Do not vacuum hot, glowing or burning ashes; only vacuum cold ashes.
• Empty and clean the dust container before and after each use.
• Do not use dust bags made of paper or bags made of similar flammable materials.
• Never use other vacuum cleaners to vacuum ashes.
• Do not place the ash vacuum cleaner on flammable or polymer surfaces, including carpets or vinyl tile floors.

1. Safety regulations

Danger!

Read all safety regulations and instructions.

Any errors made in following the safety regulations and instructions may result in an electric shock, fire and/or serious injury.

Keep all safety regulations and instructions in a safe place for future use.

This appliance is not to be used by people (including children) with disabilities, whether physical, sensory or cognitive, or by people without prior experience/adequate knowledge of the appliance, without supervision by qualified safety personnel, or instructions on how to use it. Children must always be supervised in order to ensure that they do not play with the appliance.

• Danger! Read the operating instructions before assembling and using the appliance for the first time.
• Check that the mains voltage is the same as the mains voltage specified on the rating plate.
  Pull out the power plug in the following circumstances: Whenever the appliance is not in use, before opening the appliance and before all cleaning and maintenance work.
• Never clean the appliance with solvents.
• Never pull the plug out of the socket by pulling the cable.
• Never leave the appliance unattended when operational.
• Keep away from children.
  Take care to ensure that the power cable does not get damaged by being run over, crushed, pulled or suchlike.
• Do not use the machine if the power cable is in a less than perfect condition.
  If the power cable has to be replaced, the replacement must comply with the design specifications of the manufacturer.
  Power cable: H 05 VV - F 2 x 0,75 mm2
• Never vacuum the following: Burning matches, smoldering ash and cigarette butts, combustible, caustic, inflammable or explosive substances, vapour or liquids.
  This appliance is not suitable for vacuuming dust which can be harmful to health.
• Store the appliance in a dry indoor location.
• Never use the appliance if it is damaged.
• Only allow the appliance to be serviced by an authorized customer service center.
  Only use the appliance to carry out work for which has been designed.
  Use only genuine accessories and spare parts.
  The guidelines in the operating instructions must be observed. The safety and accident-prevention regulations from the lawgiver are also to be observed.
• Important! Hazardous material must not be extracted with the ash filter.
• Do not extract ashes from prohibited fuels.
• Do not use the ash filter to extract hot, glowing or inflammable objects (e.g. charcoal, cigarettes ...).
  Danger! The ash vacuum cleaner is not suitable for vacuuming soot or fine dust.
• Danger! The extracted material must not exceed a temperature of 40^ .
• Danger! If this temperature of the extracted material exceeds 40^ , there is a risk of fire.

GB

• Danger! If the permissible temperature is exceeded, the extractor, the ash filter and the hoses could be damaged.
• Danger! Extracted material which looks as though it has cooled off on the outside may still be hot on the inside. Hot extracted material could be set alight again in the air current.
  Before beginning extraction, please wait until the material is completely cooled off. Hot ashes should not be purged with water, as the sudden temperature difference can cause ruptures to the chimney.
  Wait at least 24 hours before vacuuming an oven or a fireplace in order to be sure that the fire has gone out and the ash has cooled down.
• Check the hoses, the ash filter and the extractor regularly when extracting, to assess levels of heating.
  If the appliance heats up, switch it off, pull the mains plug out and remove the filter bag immediately. Separate the ash filter from the extractor and remove the extracted material.
  Next, let the extractor and the ash filter cool off outside, under supervision.
• If the power cable for this appliance is damaged, it must be replaced by the manufacturer or its after-sales service or similarly trained personnel to avoid danger.
  Cold ash is ash which has cooled for a sufficiently long time and no longer contains any glowing embers. This can be checked by combing through the ash with a metal object before you use the ash vacuum cleaner. Cold ash no longer radiates any perceivable heat.
  After and before vacuum cleaning, empty and clean the tank in order to prevent the accumulation of materials which could present a fire hazard in the vacuum cleaner.
  The ash vacuum cleaner is not allowed to be used for collecting harmful dusts (dust class L, M, H).

2. Layout and items supplied

2.1 Layout (Fig. 1,6)

1Handle
2 On/Off switch
3 Appliance head
4 Filter basket
5 Blow connector
6 Locking hook
7Tank
8 Suction hose connector
9 Suction tube
10 Flexible hose
11 Filter cartridge for fine ash dust.
12 Wing nut
13 Coarse filter
14 Wheels

2.2 Items supplied

Please check that the article is complete as specified in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions.

• Open the packaging and take out the equipment with care.
• Remove the packaging material and any packaging and/or transportation braces (if available).
  Check to see if all items are supplied.
• Inspect the equipment and accessories for transport damage.
  If possible, please keep the packaging until the end of the guarantee period.

Danger!

The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of swallowing or suffocating!

Ash vacuum
Original operating instructions

GB

3. Proper use

This tool is designed to vacuum up cold ashes from fireplaces, chimneys, stoves, ashtrays and similar places where ashes are collected.

The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.

Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent purposes.

4. Technical data

Mains voltage: 220-240 V ~ 50/60 Hz

Nominal output: 850 W

Tank volume: 20

Protection class:

Weight: ca. 3.9 kg

5. Before starting the equipment

Before you connect the equipment to the mains supply make sure that the data on the rating plate are identical to the mains data.

Warning!

Always pull the power plug before making adjustments to the equipment.

The appliance may only be connected to a shockproof socket.

5.1 Assembling the appliance

Fitting the appliance head (Fig. 2-5)

The appliance head (3) is fastened to the container (7) by the locking hook (6). To remove the appliance head (3), open the locking hook (6) and remove the appliance head (3). When fi tting the appliance head (3), make sure that the locking hook (6) locks into place correctly.

Plug the vacuum tube (9) onto the end of the suction hose (10).

Fit the suction hose (10) onto the connection (8) and turn until securely attached.

5.2 Fitting the fi Iter

Notice!

Never use the ash vacuum without the fi liter! Always ensure that the fi iters are perfectly secure.

Removing/fitting the pleated filter (Fig. 6)

First undo the wing nut (12) and then remove the pleated filter (11) and the filter cage (4) by pulling. Assemble in reverse order. Check that the fi iter is securely seated at all times.

Important!

The equipment comes with a safety switch (z) which does not allow the equipment to be switched on when the pleated filter and the filter basket are not fitted.

Fitting the coarse filter (Fig. 7)

Fit the coarse filter (13) as shown in Figure 7.

5.3 Fitting the wheels (Fig. 9)

Fasten the wheels (14) as shown in Figure 9.

6. Operation

6.1 ON/OFF switch (Fig. 1/2)

Press the ON/OFF switch (2) to switch the equipment ON and OFF.

6.2 Blowing

Connect the suction hose (10) to the blow connector (5) of the ash vacuum cleaner.

6.3 Cleaning the appliance head

Clean the appliance regularly with a damp cloth and some soft soap. Do not use cleaning agents or solvents; these may be aggressive to the plastic parts in the appliance.

6.4 Cleaning the container

The container can be cleaned with a damp cloth and some soft soap or under running water, depending on the amount of dirt.

6.5 Cleaning the fi Iter

Clean the filter basket (4), the pleated filter (11) and the coarse fi liter (13), e.g. by tapping and brushing or by blowing out with compressed air at low pressure.

GB

7. Replacing the power cable

Danger!

If the power cable for this equipment is damaged, it must be replaced by the manufacturer or its after-sales service or similarly trained personnel to avoid danger.

8. Cleaning, maintenance and ordering of spare parts

Danger!

Always pull out the mains power plug before starting any cleaning work.

8.1 Cleaning

• Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible.
  We recommend that you clean the appliance immediately after you use it.

8.2 Servicing

At regular intervals and before each use, check that the filters in the ash vacuum are securely fitted.

8.3 Ordering replacement parts:

Please quote the following data when ordering replacement parts:

Type of machine
Article number of the machine
Identification number of the machine
- Replacement part number of the part required

For our latest prices and information please go to www.Einhell-Service.com

9. Disposal and recycling

The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your local council offices.

10. Storage

Store the equipment and accessories in a dark and dry place at above freezing temperature. The ideal storage temperature is between 5 and 30
°C. Store the electric tool in its original packaging.

For EU countries only

Never place any electric power tools in your household refuse.

To comply with European Directive 2012/19/EC concerning old electric and electronic equipment and its implementation in national laws, old electric power tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request: As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment. The old equipment can be returned to a suitable collection point that will dispose of the equipment in accordance with national recycling and waste disposal regulations.

This does not apply to any accessories or aids without electrical components supplied with the old equipment.

Please note that batteries and lamps (e.g. light bulbs) must be removed from the tool before it is disposed of.

The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of the Einhell Germany AG.

Subject to technical changes

GB

Service information

We have competent service partners in all countries named on the guarantee certificate whose contact details can also be found on the guarantee certificate. These partners will help you with all service requests such as repairs, spare and wearing part orders or the purchase of consumables.

Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.

Category Example
Wear parts* Suction tube
Consumables*	Pleated filter, foam filter, coarse filter
Missing parts

• Not necessarily included in the scope of delivery!

In the effect of defects or faults, please register the problem on the internet at www.Einhell-Service.com. Please ensure that you provide a precise description of the problem and answer the following questions in all cases:

Did the equipment work at all or was it defective from the beginning?
Did you notice anything (symptom or defect) prior to the failure?
What malfunction does the equipment have in your opinion (main symptom)?

Describe this malfunction.

GB

Warranty certificate

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that this equipment develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made:

1. These guarantee terms apply solely to consumers, i.e. natural persons, who do not want to use this product in connection with either their commercial or other self-employed activities. These guarantee terms regulate additional guarantee services which the undermentioned manufacturer promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory rights of guarantee are not affected by this guarantee. Our guarantee is free of charge to you.

2. The guarantee services cover only defects due to material or manufacturing faults on the new product which you have bought in the European Union from the undermentioned manufacturer and are limited to either the rectification of said defects or the replacement of the product, whichever we prefer. Please note that only equipment under the brand name "Professional" has been designed for use in commercial, trade or professional applications. For all other products the guarantee is invalidated if the equipment is used within the guarantee period in commercial, trade or industrial applications or for other equivalent activities.

3. Our guarantee does not cover:

4. Damage to the equipment caused by failure to comply with the installation/assembly instructions or by unprofessional installation; damage caused by failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or current type); damage caused by failure to comply with the maintenance and safety regulations; damage caused by exposing the equipment to abnormal environmental conditions; damage resulting from poor care and maintenance.

5. Damage to the equipment caused by misuse or incorrect applications (e.g. overloading the equipment or using non-approved attachments or accessories); damage caused by foreign bodies (e.g. sand, stones, dust, ...) getting inside the equipment. Damage in transit; damage caused by force or external influences (e.g. by dropping the equipment).

6. Damage to the equipment or parts of the equipment which is owed to use-related, normal or otherwise natural wear. For example, batteries and battery packs are manufactured with a cycle limit for design-related reasons. Wear is negatively influenced in particular by load demands and charging speeds as well as exposure to heat, cold, vibration and impact.

7. The guarantee is valid for a period of 2 years starting from the purchase date of the equipment. Guarantee claims must be submitted before the end of the guarantee period and within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the equipment even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or for any replacement parts fitted. This also applies if on-site service is used.

8. To assert your guarantee claim, register the defective equipment at: www.Einhell-Service.com. You will need to provide proof of purchase of the new item of equipment. Equipment returned without such proof or without a rating plate are excluded from the guarantee services because of the lack of traceability. If the defect is covered by our guarantee, then either the item in question will be repaired immediately and returned to you or we will send you a new replacement.

9. If you have taken the equipment with you to a different EU country than where you bought it, we will arrange for a local service partner to provide the guarantee services. If you take the equipment outside the EU, the guarantee will not apply.

Of course, we are also happy to offer a chargeable repair service for any defects which are not covered or no longer covered by the scope of this guarantee. To take advantage of this service, please send the equipment to our service address. We draw attention to the restrictions of this guarantee concerning wear parts, consumables and missing parts as presented in the service information included in this operating manual.

Warrantor/Service:

Einhell UK Ltd, Unit 10, 1st Floor, Champion's Business Park, Arrowe Brook Road, Upton, Wirral, CH49 0AB

F

Danger!

Chere cliente, cher client.

3. WAARSCHUWING: brandgevaar

Stimata clienta, stimate client.

produsele noastre sunt supuse unui control de calitate riguros. Dacà totusi vreodata acest aparat nu va fonctiona ireprosabi, ne pare foarte rau si va rugam sa va adresati centrului noctru service, la adresa indicata la finalul acestui certificat de garantie. Bineinteles ca va stam si la Telefon cu placere la disposizte, la numarul de service mentionat. Pentru revendicarea pretentiilor de garantie trebuie tinut cont de urmatoarele:

Evaakrih h avakkawon avi ia iotpoi

O iokntnc nkektipnnc okeunc unoxpeout ai vti n cpiopnc va uubalei on wotn avakkwn o nepintwnou neuvexicva xnpouonoei tn ouokeun. H naia ouokeun motei va npaxwnei o kevtpo nktipnv kewuovuw me tvy evvoia twv evikwv voowy avakkwn kai diaxepionc anoBAntw. De vupteiaaavovta ta tmjata naiw oukeuwkai ta bonentka otoixia xwpi nktipka efaptnmuata.

Napakaouke kata nv diaeon ota anopmuata va npoeEte va aapaeeov oi mataiec ka taiedn ano tn ouokeun (x.y.lambda).

H avatunwnon oonoiaaonote aannc mopnns avanapayyn nts teknpwo ns aanawv
deltaiooyntikwovavafepovtalotaipovtaakoun kalantoaaatika,etitpenetai mvo p
pntouykataeom tnC Einhll Germany AG.

Me eipufuae n Te xviikw Tportonoioeaw

GR

Evnpewon yia to epbiC

5. Pre puštanja u pigeon

Pre ukljucivanja proverite odgovaraju li podaci na tipskoj plocici podacima o mrezi.

Upozorenje!

Pre negro počnete da podesavate uredaj, iz-vucite utikač iz uticnice.

Uredaj sme da se prikiuci samo na uticnicu sa zastitnim kontaktom!

5.1 Montaza ureda

Montažaglaveuredaja (sl.2-5)

Glavu uredaja (3) priocrstite pomocukica za zatvaranje (6) na spremnik (7). Da bistie skinuli glavu uredaja (3) otvorite kukice za zatvaranje (6) i skinite glavu (3). Kod montaze glave (3) pripazite da se kukice (6) isprawno uglave.

Usisnu cev (9) nataknite na kraj usisnog creva (10).

Utaknite usisno crevo (10) u priključak (8) i obrotanjem ga učvrstite.

5.2 Montaza fi Itera

Napomena!

Jeff Dong/Product-Management

First CE:2024

Art-No.:23.516.67

I-No.:21014

Subject to change without notice

Archive-File/Record: NAPR034063

Documents registrar: Felix Hofner

Wiesenweg 22, D-94405 Landau/Isar

* GB Ach vacuum - Aspirater du sandres - AAspiracenere - DKV Asseguer - S Asagurka - CZ Vysvazao na popel - SK Vysvazao na popel - NL Aszugir - E Aspirater de centro - FN Tlukmalr - SLO Sasankar na pape - H Hamusvdo - RO Aspirater perin cangal - H G K Pkrtak opolina y a otyrcky - P Aspirater de dinas - HR BHI Lusaez opelra - RS Ustaek opelra - PL Okuzurac da popluoi - TR KI Asopker - RUS flucnizum zua - EE Tluimur - LV Peine sccus - LT Pemini, statalys BG Cwiprntayna na nenon: UKR Tpovnyeia for koxiunmian zanam - MRC Bocenyana na nenon

Declaration of conformity

We, Einhell UK Ltd

Champions Business Park, First Floor Unit 10, Arrowe Brook Rd, Upton, Wirral CH49 0AB, United Kingdom

declare the conformity to UK standards and legislation was assessed for:

Simple Pressure Vessels (Safety) Regulation
Electrical Equipment (Safety) Regulation
Radio Equipment Regulation
Personal Protective Equipment Regulation
The Ecodesign for Energy-Related Products and Energy Information Regulation
The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulation
Nolse Emisslon in the Environment by Equipment for use Outdoors Regulation
Noise:measuredL = dB Aguaranteed L_WA = dB A
Supply of Machinery (Safety) Regulation
Annex IV
Notified Body:
Reg.No.:

Standard References: BS EN 60335-1; BS EN 60335-2-2; BS EN 62233; BS EN IEC 55014-1; BS EN IEC 55014-2; BS EN IEC 61000-3-2; BS EN 61000-3-3

Wirral, 2024.12.18

Tom Chambers, Managing Director Einhell UK Ltd.

Archive-File/Record: NAPR034063

Article Number: 23.516.67 I-No.: 21014

Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar, Germany

Documents registrar: Felix Hofner

EH 02/2025 (01)