Q: How to replace the spark plug on the RGPM 51 S?

Before any intervention, stop the engine and let it cool completely , then remove the spark plug connector by pulling it firmly. This step is essential for your safety. The Briggs & Stratton 190 cm³ engine of your Einhell RGPM 51 S uses a Briggs & Stratton 591868 spark plug or its equivalent Champion RJ19LM . The spark plug wrench (21 mm) is provided with your mower. Proceed as follows: Locate the spark plug on the single-cylinder engine Use the provided spark plug wrench to unscrew the old spark plug by turning counterclockwise Inspect the condition of the spark plug: if it is heavily sooted, caked, or worn, proceed with the replacement Check that the electrode gap of the new spark plug is set between 0.20 and 0.30 mm (you can use a feeler gauge or refer to the Briggs & Stratton manual) Install the new spark plug and tighten it firmly by hand, then finish tightening with the wrench without excessive force (about 2 to 3 turns of the wrench after contact) Reconnect the spark plug connector by pushing it until you hear a click For optimal performance, it is recommended to replace the spark plug once a year. If the mower does not start after replacement, ensure that the connector is properly connected and that there is no play.

Q: What oil to use for the EINHELL EURO 8/24 compressor?

For the EINHELL EURO 8/24 compressor, you should use SAE 15W/40 oil or an equivalent product. Important maintenance tips for the oil: First oil change: after 100 hours of operation Subsequent changes: every 500 hours Level check: regularly check the oil visibility window - the level should remain between the red mark and the upper edge Disposal: used oil must be poured into an approved collection center for used oils Also, make sure to drain the condensation water daily through the lower drain valve of the 24-liter tank, as water accumulation can affect the oil quality.

Q: The device does not start even though the battery is fully charged (green LED)

The green LED indicates that your battery is fully charged - this does not mean there is a power issue. If the device does not work despite a green battery, you must follow the startup protocol : Keep the startup lock (position 3) pressed Simultaneously press the power switch (position 4) Both controls must be activated simultaneously . If you only hold one of them, the device will not start. Another point to check: If two LEDs light up during charging, this indicates either a temperature issue or a charging fault. In this case, make sure that: The charger is properly connected to the mains The charging contacts are clean (no dust or dirt) The ambient temperature is normal (slight warming during charging is normal) If after these checks the device still does not work, contact the manufacturer's customer service.

Q: Are the blades for oscillating tools sold at Action compatible with the TC-MG 220 E?

The fastening system of the TC-MG 220 E relies on tool holder pins that fit into the blade cutouts , which is then secured by a hexagon socket screw (Allen key provided). This is neither the OIS system nor the Starlock: it is a universal standard with 2 pins + central screw, very common among entry-level and mid-range oscillating tools. The universal blades for oscillating tools sold at Action are often compatible with this type of fastening, provided that their cutouts correspond well to the tool holder pins. The visual difference you noticed may have several explanations: Cosmetic difference only (color, surface treatment, metal thickness): no impact on fastening, the blade will be compatible. Slight misalignment of the cutouts : if the holes do not perfectly align with the pins, the blade will not be held properly - do not force it. Different system (Starlock star, OIS notch): incompatible with the TC-MG 220 E. Simple test before buying or mounting the blade: place the blade on the tool holder without tightening the screw. If the pins fit naturally into the cutouts and the blade is flat and stable, the fastening is compatible. If the blade tilts, forces, or does not align, do not attempt to mount it. If in doubt, certified compatible original accessories are available at www.isc-gmbh.info .

Question 1

How to replace the spark plug on the RGPM 51 S?

Accepted Answer

Before any intervention, stop the engine and let it cool completely, then remove the spark plug connector by pulling it firmly. This step is essential for your safety.

The Briggs & Stratton 190 cm³ engine of your Einhell RGPM 51 S uses a Briggs & Stratton 591868 spark plug or its equivalent Champion RJ19LM. The spark plug wrench (21 mm) is provided with your mower.

Proceed as follows:

Locate the spark plug on the single-cylinder engine
Use the provided spark plug wrench to unscrew the old spark plug by turning counterclockwise
Inspect the condition of the spark plug: if it is heavily sooted, caked, or worn, proceed with the replacement
Check that the electrode gap of the new spark plug is set between 0.20 and 0.30 mm (you can use a feeler gauge or refer to the Briggs & Stratton manual)
Install the new spark plug and tighten it firmly by hand, then finish tightening with the wrench without excessive force (about 2 to 3 turns of the wrench after contact)
Reconnect the spark plug connector by pushing it until you hear a click

For optimal performance, it is recommended to replace the spark plug once a year. If the mower does not start after replacement, ensure that the connector is properly connected and that there is no play.

Question 2

What oil to use for the EINHELL EURO 8/24 compressor?

Accepted Answer

For the EINHELL EURO 8/24 compressor, you should use SAE 15W/40 oil or an equivalent product.

Important maintenance tips for the oil:

First oil change: after 100 hours of operation
Subsequent changes: every 500 hours
Level check: regularly check the oil visibility window - the level should remain between the red mark and the upper edge
Disposal: used oil must be poured into an approved collection center for used oils

Also, make sure to drain the condensation water daily through the lower drain valve of the 24-liter tank, as water accumulation can affect the oil quality.

Question 3

Which batteries (accumulators) are compatible with the GCLC 1815 T hedge trimmer?

Accepted Answer

The EINHELL GCLC 1815 T hedge trimmer works with the lithium-ion accumulator GC-LC 1815 T with a voltage of 18V DC and a capacity of 1.5 Ah.

This accumulator is a model specifically designed by Einhell for this device. It charges with the charger NG-GC-LC 1815 T in about 1 hour.

The battery is completely waterproof and maintenance-free. Important: avoid completely discharging it, as this would damage it. For long-term storage, remove it from the device and store it in a cool, dry place between 5 and 30°C.

Question 4

What are the characteristics of the motor of the EINHELL GP-CM 36/52 S Li BL?

Accepted Answer

Motor Characteristics

The EINHELL GP-CM 36/52 S Li BL lawn mower is equipped with a brushless motor (without brushes) of 18V powered by Power-X-Change batteries. The manual does not specify the power in watts, but here are the available technical specifications:

Motor type: Brushless (without brushes)
Voltage: 18V DC
Rotation speed: 3000 rpm
Battery: 4 Power-X-Change 18V batteries, 5.2 Ah (2x2 configuration)
Guaranteed sound level: 98 dB(A)

The brushless motor ensures maintenance-free operation of the brushes and optimal energy efficiency. The 18V voltage combined with the 5.2 Ah capacity per battery provides sufficient autonomy for mowing a standard residential lawn.

Question 5

The device does not start even though the battery is fully charged (green LED)

Accepted Answer

The green LED indicates that your battery is fully charged - this does not mean there is a power issue.

If the device does not work despite a green battery, you must follow the startup protocol:

Keep the startup lock (position 3) pressed
Simultaneously press the power switch (position 4)

Both controls must be activated simultaneously. If you only hold one of them, the device will not start.

Another point to check: If two LEDs light up during charging, this indicates either a temperature issue or a charging fault. In this case, make sure that:

The charger is properly connected to the mains
The charging contacts are clean (no dust or dirt)
The ambient temperature is normal (slight warming during charging is normal)

If after these checks the device still does not work, contact the manufacturer's customer service.

Question 6

Where to buy a replacement saw blade for the EINHELL TCTS 1200?

Accepted Answer

According to the manual for the EINHELL TCTS 1200, saw blades are consumable wear parts that need to be replaced regularly. Here’s how to obtain a new blade:

Recommended Purchases

EINHELL After-Sales Service - This is the preferred option for obtaining authentic blades specifically suited for your TCTS 1200 model. Contact EINHELL support directly with your model number.
Authorized EINHELL Dealers - Official distributors offer original spare parts and can advise you on compatibility.

Main Features of Your Saw

Your EINHELL TCTS 1200 is equipped with a blade of 250 mm diameter rotating at 5000 rpm. Ensure that when you order, the new blade meets these specifications for optimal cutting and safety.

Tip: Before replacing the blade, disconnect the power supply and wait for the rotation to stop completely (the blade spins at 5000 rpm, braking may take a few seconds).

Question 7

Are the blades for oscillating tools sold at Action compatible with the TC-MG 220 E?

Accepted Answer

The fastening system of the TC-MG 220 E relies on tool holder pins that fit into the blade cutouts, which is then secured by a hexagon socket screw (Allen key provided). This is neither the OIS system nor the Starlock: it is a universal standard with 2 pins + central screw, very common among entry-level and mid-range oscillating tools.

The universal blades for oscillating tools sold at Action are often compatible with this type of fastening, provided that their cutouts correspond well to the tool holder pins. The visual difference you noticed may have several explanations:

Cosmetic difference only (color, surface treatment, metal thickness): no impact on fastening, the blade will be compatible.
Slight misalignment of the cutouts: if the holes do not perfectly align with the pins, the blade will not be held properly - do not force it.
Different system (Starlock star, OIS notch): incompatible with the TC-MG 220 E.

Simple test before buying or mounting the blade: place the blade on the tool holder without tightening the screw. If the pins fit naturally into the cutouts and the blade is flat and stable, the fastening is compatible. If the blade tilts, forces, or does not align, do not attempt to mount it.

If in doubt, certified compatible original accessories are available at www.isc-gmbh.info.

Question 8

Does the EINHELL GE-EM 1233 M electric lawn mower have a fuse protection or an integrated safety device?

Accepted Answer

The EINHELL GE-EM 1233 M electric lawn mower does not have a built-in fuse within the device itself. However, it is equipped with a safety device called a safety switch that prevents accidental starting of the machine. This mechanism requires the user to press a safety trigger before being able to activate the on/off button, thus ensuring safe use.

Furthermore, to ensure electrical protection, it is recommended that the electrical outlet used to plug in the mower is protected by:

A residual current device (RCD) with a maximum threshold of 30 mA
A 16 A circuit breaker

These devices are not integrated into the mower but must be present in the electrical installation where the machine is used, in order to prevent electrical hazards and ensure user safety.

Question 9

What does the flashing green light on the charging station of the EINHELL FREELEXO+ robotic mower mean?

Accepted Answer

The flashing green light on the charging station of your EINHELL FREELEXO+ robotic mower generally indicates that the robot is in charging mode. Here’s what it means and the actions to check:

Meaning of the flashing green light

A flashing green light indicates that the station is charging the battery of the robotic mower.

What to do if the light is flashing?

Check the position of the robot: Make sure the robot is correctly positioned on the charging station, with the charging contacts properly aligned.
Check the power supply: Ensure that the station is plugged in and that the power cable is not damaged.
Be patient: The flashing may last during charging. If the charging takes a long time, this may be normal.
Monitor the battery: If the green light continues to flash for an extended period without the battery seeming to charge, there may be an issue with the battery or the charging station.

In summary, a flashing green light is a normal charging indicator, but you should ensure everything is properly connected and that the robot is correctly positioned. If the problem persists, it may be necessary to check the condition of the battery or the charging system.

Question 10

What buttons are present on the control panel of the EINHELL FREELEXO 500 LCD BT+ robotic mower and what do they do?

Accepted Answer

The control panel of the EINHELL FREELEXO 500 LCD BT+ robotic mower is equipped with an LCD screen and 7 main buttons that allow you to fully control and configure the device.

The LCD screen (50) displays the navigation menu, the status of the robot, and all important information such as battery level, the status of the current program, and any error messages.

The buttons on the control panel are:

SET button (51): This settings button allows you to access the fundamental parameters of the robot. It provides access to the mowing schedule configuration, cutting height (from 25 to 60 mm), mowing times, security PIN management, date and time, language selection, and software version.
MODE button (52): This mowing program button allows you to select and start the various available mowing programs. You can choose between the main area and the secondary area according to your configuration, or select the “Return to charging station” option.
START button (53): This start button launches the selected mowing program. Once the program is chosen via MODE, press START for the robot to begin the mowing cycle.
BACK button (54): This back button allows you to exit a menu or settings page and return to the previous screen. It interrupts navigation without validating changes.
Navigation buttons (55): These directional buttons allow you to navigate through the menus on the LCD screen to access different sections and modify settings. You will use them to select options and adjust values (cutting height, times, etc.).
OK button (56): This confirmation button validates your choices and the modifications made to the settings. Once your adjustments are made, press OK to save them.

Red STOP button (3): This emergency stop button located at the top of the robot allows you to immediately stop the mowing cycle and unlock the protective cover of the LCD screen. After pressing STOP, the robot stops and waits for your instructions. A window then appears on the screen to confirm the lifting of the STOP status.

These controls facilitate the complete management and customization of your FREELEXO 500 LCD BT+ robotic mower for optimal use according to your needs.

User manual EINHELL : user manuals and guides in PDF

Models EINHELL most viewed

Browse manuals EINHELL by appliance type

Recent questions about devices EINHELL