GE-SP 750 LL - Pumps EINHELL - Free user manual and instructions

Product Type	Submersible Clean Water Pump
Model	GE-SP 750 LL
Power	750 W
Voltage	230 V ~ 50 Hz
Max. Flow Rate	15500 L/h
Max. Delivery Head	7 m
Max. Immersion Depth	7 m
Max. Particle Size	5 mm
Hose Connection	1" (25 mm) external thread
Thermal Protection	Yes
Float Switch	Automatic on/off
Power Cable Length	10 m
Housing Material	Plastic
Dimensions (L x W x H)	31 x 18 x 36 cm
Weight	5.5 kg

Frequently Asked Questions - GE-SP 750 LL EINHELL

How do I prime the pump before use?

Ensure the pump is fully submerged in water. The pump is self-priming up to 7 m depth. For initial use, submerge completely and allow air to escape from the outlet hose.

Can the pump run dry?

No, running dry can damage the pump. Always ensure the pump is submerged in water. The integrated float switch helps prevent dry running by cutting power when water level drops.

What is the maximum particle size the pump can handle?

The pump can handle particles up to 5 mm in diameter. For larger debris, use a pre-filter or avoid pumping dirty water.

How do I clean the pump after use?

Disconnect from power, remove from water, and rinse with clean water. Clean the filter and impeller area from debris. Store in a dry place.

Why does the pump not start?

Check if power is applied, if the float switch is free to move, and if the pump is submerged. If thermal protection has tripped, allow cooling for 15 minutes.

What is the maximum operating temperature of the liquid?

The maximum water temperature should not exceed 35°C to prevent damage to the pump.

Can I use an extension cord?

Yes, but ensure the extension cord has a cross-section of at least 1.5 mm² and is suitable for outdoor use. Keep the connection dry.

How does the float switch work?

The float switch automatically turns the pump on when the water level rises and off when it drops. Adjust the float cable length to set the desired on/off levels.

What maintenance is required?

Regularly check the power cable for damage, clean the pump and filter after use, and lubricate the shaft seal annually if recommended.

Where do I find spare parts?

Spare parts such as the float switch, impeller, and seals are available from Einhell service centers or authorized dealers. Refer to the manual for part numbers.

USER MANUAL GE-SP 750 LL EINHELL

GB Original operating instructions Submersible pump

7CE

-2-

HE

א.הוֹרָה אַלְבָרָה

הכלה, tomato and (terre tomato and) will be called as it is (terre tomato and

1. Safety regulations
2. Layout and items supplied
3. Proper use
4. Technical data
5. Before starting the equipment
6. Operation
7. Replacing the power cable
8. Cleaning, maintenance and ordering of spare parts
9. Disposal and recycling
10. Storage
11. Troubleshooting guide

GB

Danger! - Read the operating instructions to reduce the risk of injury

This equipment can be used by children aged 8 years and above and by persons with reduced physical, sensory, or mental capabilities or those lacking experience and knowledge, provided they are supervised or have been instructed in the safe use of the equipment and understand the hazards involved. Children must not play with the equipment. Cleaning and user maintenance must not be performed by children without supervision.

If the power cable for this equipment is damaged, it must be replaced by the manufacturer, its after-sales service, or similarly qualified personnel to avoid hazards.

GB

Danger!

When using the equipment, certain safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations carefully. Keep this manual in a safe place so that the information is always available. If you pass the equipment on to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents that occur due to failure to follow these instructions and the safety instructions.

1. Safety regulations

Danger!

Read all safety regulations and instructions. Any errors made in following the safety regulations and instructions may result in electric shock, fire, and/or serious injury. Keep all safety regulations and instructions in a safe place for future use.

Danger!

The pump must be powered via an earth-leakage circuit breaker (RCD) with a rated fault current of no more than 30 mA (according to VDE 0100 Part 702 and 738).

The equipment is not designed for use in swimming pools, paddling pools of any kind, or other bodies of water in which people or animals may be present during operation. It is prohibited to operate the equipment if a person or animal is in the danger area. Ask your electrician!

- Before you put the equipment into operation, arrange for a specialist to check that the earthing, protective multiple earthing or residual-current operated circuit-breaker circuit comply with the safety regulations of the power supply company and work correctly.

lations of the power supply company and work correctly.

• The electrical plug-in connections must be protected from wet conditions.
• If there is a risk of flooding, place the plug-in connections in an area which is safe from flooding.
• Strictly avoid pumping aggressive liquids and abrasive substances.
• Protect the equipment from dry running.
• Take suitable measures to keep the equipment out of the reach of children.
• Take suitable measures to keep the equipment out of the reach of children.
• There is a risk of the liquid becoming contaminated by escaping lubricant.

2.1 Layout (Figs. 1/2/3)

Carry handle with cable rewind

1. Carry handle with cable rewind
2. Hose connection
3. Fastening nut
4. Pump housing
5. Intake cage
6. Power cable

2.2 Items supplied

Please check that the article is complete as specified in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating

GB

instructions.

• Open the packaging and take out the equipment with care.
• Remove the packaging material and any packaging and/or transportation braces (if available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for transport damage.
• If possible, please keep the packaging until the end of the guarantee period.

Danger!

The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of swallowing or suffocating!

• Original operating instructions

3. Proper use

The equipment you have purchased is designed to pump water with a maximum temperature of 35 °C. This equipment must never be used for other liquids, especially engine fuels, cleaning agents and other chemically-based products! Installed in a shaft, the equipment provides protection from flooding. However, it can be used wherever you want to move water, e.g. in the house, in the garden, and for many other applications. The equipment must not be used to operate swimming pools!

If you want to use the equipment in bodies of water with a natural, muddy bottom, place the equipment in a slightly elevated position, e.g. on bricks.

The equipment is not designed for continuous operation, e.g. as a circulating pump in a pond. In this case the equipment's anticipated life will be greatly shortened because the equipment was not designed for continuous loading.

The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.

Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the

machine is used in commercial, trade or industrial businesses or for equivalent purposes.

4. Technical data

Mains connection .....230 V ~ 50 Hz Power rating .....750 W Max. pumping rate 15,000 l/h Max. delivery head 10 m Max. immersion depth 5 m Max. water temperature 35 °C Hose connection ...... ca. 42 mm (G 1 1/4) AG Max. size of foreign bodies: 0.5 mm Switching point height: ON ....max. approx. 12 cm Switching point height: OFF .....min. approx. 3 cm Min. extraction height: 2 mm Protection type: IPX8

5. Before starting the equipment

5.1 Fitting the carry handle (Fig. 2/3)

• Connect the carry handle (1) to the pump (Fig. 2)
• Secure the carry handle (1) with the fastening nut (3) (Fig. 3).

5.2 Installation

The equipment can be installed either:

• Stationary with rigid tubing

or

• Stationary with a flexible hose line

Note!

When installing, never hang the equipment by the discharge line or by the power cable. The equipment must be hung up with the provided carry handle or it must rest on the bottom of the shaft. To ensure that the equipment works properly, the bottom of the shaft always must be free of sludge and other accumulations of dirt. If the water level is too low, the sludge in the shaft can quickly dry out and hinder the equipment from starting. It is necessary therefore to check the equipment regularly (carry out trial start-ups).

Note:

The pump shaft should measure at least 40 x 40 x 50 cm so that the floating switch can move freely.

5.3 Mains connection

The equipment you have purchased comes with an earthing-pin plug. The equipment is designed for connection to a socket outlet with earthing contact for 230 V ~ 50 Hz. Make sure that the socket-outlet is sufficiently fused (at least 6 A) and in good working order. Insert the power plug in the socket-outlet and the equipment is ready for operation.

Important!

To rule out danger, this work must be left strictly to a specialist electrician or Customer Service.

6. Operation

You can put the equipment into operation after you have thoroughly read the installation and operating instructions. Pay attention to the following points:

• Make sure that the equipment is set up securely. - Check that the discharge line is fitted correctly. • Make sure that the electrical connection is 230 V ~ 50 Hz. - Check that the electrical socket-outlet is in good working order. • Make sure that no moisture or water can ever reach the power connection. • Make sure that the equipment does not run dry.

Function of the integrated floating switch

Automatic mode:

Selector switch (A) must be in the lower position during automatic mode (Fig. 4).

This activates the integrated floating switch. The height of activation is approximately 12 cm. The equipment switches off again when a height of approximately 3 cm is reached.

Manual mode/shallow water:

Selector switch (A) must be in the upper position to operate manually or in shallow water (Fig. 5). This bridges the integrated floating switch so that the equipment runs continuously. Water can be pumped down to 2 mm in manual mode.

Please note:

The depth of water must be at least 50 mm before the equipment can be run in manual mode!

Important.

The equipment must not run dry!

7. Replacing the power cable

Danger!

If the power cable for this equipment is damaged, it must be replaced by the manufacturer or its after-sales service or similarly trained personnel to avoid danger.

8. Cleaning, maintenance and ordering of spare parts

Important!

• Unplug the power plug prior to any maintenance work.
• For mobile applications, the equipment should be cleaned with clear water after every usage.
• For stationary installation, it is recommended that you check the floating switch for proper functioning every three months.
• Use a water jet to remove any lint or fibrous particles that may have become trapped in the housing.
• Remove sludge from the shaft bottom and clean the shaft walls every 3 months.
• Use clear water to remove deposits from the floating switch.

8.1 Cleaning the paddle wheel

If a lot of deposits collect in the housing, the bottom part of the equipment must be dismantled as follows:

1. Disconnect the intake cage from the housing.
2. Clean the paddle wheel with clear water. Important! Do not put down or rest the equipment on the paddle wheel!
3. Assemble in reverse order.

8.2 Maintenance

There are no parts inside the equipment which require additional maintenance.

8.3 Ordering replacement parts:

Please quote the following data when ordering replacement parts:

• Type of machine • Article number of the machine • Identification number of the machine - Replacement part number of the part required For our latest prices and information please go to www.Einhell-Service.com

9. Disposal and recycling

The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your local council offices.

10. Storage

Store the equipment and accessories in a dark and dry place at above freezing temperature. The ideal storage temperature is between 5 and 30 °C. Store the electric tool in its original packaging.

11. Troubleshooting guide

Faults Cause	Remedy
Theequipment does not start	- Power supply not connected- Observe the autostart level	- Check power supply- Turn the autostart level to the correct position
Theequipment does not pump	- Intake sieve clogged- Discharge hose kinked	- Clean intake sieve with water jet- Unkink the hose
Theequipment does not cut out	- Observe the autostart level - Turn the autostart level to the correct position
Insufficient pumping rate	- Intake sieve clogged- Performance reduced due to heavily contaminated and abrasive water impurities	- Clean intake sieve- Clean equipment and replace wear parts
The equipment switches off after briefly running	- Motor circuit-breaker switches the equipment off due to excessive water contamination- Water temperature too high; motor circuit-breaker switches the equipment off	- Unplug power plug and clean equipment and shaft- Ensure that maximum permissible water temperature (35 °C) is not exceeded

For EU countries only

Never place any electric power tools in your household refuse.

To comply with European Directive 2012/19/EC concerning old electric and electronic equipment and its implementation in national laws, old electric power tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request:

As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment. The old equipment can be returned to a suitable collection point that will dispose of the equipment in accordance with the national recycling and waste disposal regulations. This does not apply to any accessories or aids without electrical components supplied with the old equipment.

Please note that batteries and lamps (e.g. light bulbs) must be removed from the tool before it is disposed of.

The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of the Einhell Germany AG.

Subject to technical changes

GB

Service information

We have competent service partners in all countries named on the guarantee certificate whose contact details can also be found on the guarantee certificate. These partners will help you with all service requests such as repairs, spare and wearing part orders or the purchase of consumables.

Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.

Category Example
Wear parts* Impeller
Consumables*
Missing parts

* Not necessarily included in the scope of delivery!

In the effect of defects or faults, please register the problem on the internet at www.Einhell-Service.com. Please ensure that you provide a precise description of the problem and answer the following questions in all cases:

• Did the equipment work at all or was it defective from the beginning? • Did you notice anything (symptom or defect) prior to the failure? • What malfunction does the equipment have in your opinion (main symptom)? Describe this malfunction.

Warranty certificate

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that this equipment develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made:

1. These guarantee terms apply solely to consumers, i.e. natural persons, who do not want to use this product in connection with either their commercial or other self-employed activities. These guarantee terms regulate additional guarantee services which the undermentioned manufacturer promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory rights of guarantee are not affected by this guarantee. Our guarantee is free of charge to you.
2. The guarantee services cover only defects due to material or manufacturing faults on the new product which you have bought in the European Union from the undermentioned manufacturer and are limited to either the rectification of said defects or the replacement of the product, whichever we prefer. Please note that only equipment under the brand name "Professional" has been designed for use in commercial, trade or professional applications. For all other products the guarantee is invalidated if the equipment is used within the guarantee period in commercial, trade or industrial applications or for other equivalent activities.
3. Our guarantee does not cover:
4. Damage to the equipment caused by failure to comply with the installation/assembly instructions or by unprofessional installation; damage caused by failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or current type); damage caused by failure to comply with the maintenance and safety regulations; damage caused by exposing the equipment to abnormal environmental conditions; damage resulting from poor care and maintenance.
5. Damage to the equipment caused by misuse or incorrect applications (e.g. overloading the equipment or using non-approved attachments or accessories); damage caused by foreign bodies (e.g. sand, stones, dust, ....) getting inside the equipment. Damage in transit; damage caused by force or external influences (e.g. by dropping the equipment).
6. Damage to the equipment or parts of the equipment which is owed to use-related, normal or otherwise natural wear. For example, batteries and battery packs are manufactured with a cycle limit for design-related reasons. Wear is negatively influenced in particular by load demands and charging speeds as well as exposure to heat, cold, vibration and impact.
7. The guarantee is valid for a period of 2 years starting from the purchase date of the equipment. Guarantee claims must be submitted before the end of the guarantee period and within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the equipment even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or for any replacement parts fitted. This also applies if on-site service is used.
8. To assert your guarantee claim, register the defective equipment at: www.Einhell-Service.com. You will need to provide proof of purchase of the new item of equipment. Equipment returned without such proof or without a rating plate are excluded from the guarantee services because of the lack of traceability. If the defect is covered by our guarantee, then either the item in question will be repaired immediately and returned to you or we will send you a new replacement.
9. If you have taken the equipment with you to a different EU country than where you bought it, we will arrange for a local service partner to provide the guarantee services. If you take the equipment outside the EU, the guarantee will not apply.

Of course, we are also happy to offer a chargeable repair service for any defects which are not covered or no longer covered by the scope of this guarantee. To take advantage of this service, please send the equipment to our service address. We draw attention to the restrictions of this guarantee concerning wear parts, consumables and missing parts as presented in the service information included in this operating manual.

Warrantor/ Service:

Einhell UK Ltd, Unit 10, 1st Floor, Champion's Business Park, Arrowe Brook Road, Upton, Wirral, CH49 0UQ

EH 07/2023 (01)