E5111 - Weather Station Emos - Free user manual and instructions

USER MANUAL E5111 Emos

GB | Wireless Weather Station Specications: clock controlled by DCF radio signal indoor temperature: -10°C to +50°C outdoor temperature: -40°C až +70°C temperature resolution: 0.1°C temperature measurement accuracy: ±1°C indoor humidity: 1 % to 99 % RH outdoor humidity 20 % to 95 % RH humidity resolution: 1 % RH humidity measurement accuracy: ±2 % RH in 20 % to 80 % range, ±4 % RH in other ranges barometric pressure measurement range: 300 hPa to 1 200 hPa wireless sensor: transmission frequency 433 MHz, 10 mW e.r.p. max. radio signal range: up to 50 m in an open area number of sensors for connection: max. 3 Power supply: main station: 3× 1.5 V AAA batteries (not included) adapter, 230 V AC/5 V DC, 600 mA (included) sensor: 2× 1.5 V AAA batteries (not included) Weather Station Description Front Side Screen – Icons (See Fig. 1) 1 – dew point 2 – mould indicator 3 – outdoor sensor channel number 4 – wireless communication with sensor 5 – sensor batteries low 6 – outdoor clothing index 7 – outdoor temperature 8 – max/min outdoor temperature and humidity 9 – outdoor temperature trend 10 – weather forecast 11 – pressure value 12 – pressure trend 13 – indoor temperature trend 14 – max/min indoor temperature and humidity 15 – indoor temperature 16 – heat index – smiley face 17 – station batteries low 18 – indoor humidity trend 19 – indoor humidity 20 – summer time 21 – moon phase 22 – day of the week 23 – alarm no. 1, 2 activation 24 – day4 25 – time 26 – month 27 – outdoor humidity trend 28 – outdoor humidity 29 – high heat index 30 – DCF signal reception Back and Top of the Weather Station (See Fig. 2) 1 – MODE button CH button SNOOZE/LIGHT button UP button DOWN button ALARM button 2 – hole for hanging 3 – stand 4 – battery compartment 5 – indoor temperature and humidity sensor 6 – power adapter socket Sensor Description (See Fig. 3) A – LED of signal transmission from the sensor B – sensor screen C – hole for hanging D – battery cover E – battery compartment F – CH button (sensor channel number setting – 1/2/3) G – °C/°F button H – wired temperature probe (1 m) Attention Only use 1.5 V alkaline batteries of the same type; do not use rechargeable 1.2 V batteries. The lower voltage may cause both of the units to not function. Getting Started

1. Connect the power adapter to the weather station and insert the batteries (3× 1.5 V AAA). Then

insert batteries into the wireless sensor (2× 1.5 V AAA). Make sure the polarity is correct when inserting the batteries to avoid damaging the weather station or sensor.

2. The pressure unit icon on the weather station‘s screen will start ashing – set it using the UP/

DOWN buttons and conrm by pressing SNOOZE/LIGHT.

3. The pressure value will start ashing – set it using the UP/DOWN buttons and conrm by

pressing SNOOZE/LIGHT.

4. The weather forecast icon will start ashing – set it using the UP/DOWN buttons and conrm

by pressing SNOOZE/LIGHT. The setting process will be automatically cancelled if you do not press any button for 20 seconds.

5. The icon for wireless communication with sensor

will start ashing, indicating that the weather station is searching for signal from the outdoor sensor. Place the two units next to each other. If outdoor temperature does not appear within 3 minutes, the weather station will stop searching for signal, the icon for wireless communication with sensor will stop ashing and outdoor temperature/humidity will be displayed as --. If signal from the sensor is not detected, repeat the process from step 1. We recommend placing the sensor on the north side of the house. The range of the sensor may decrease substantially in areas with a large number of obstacles. The sensor is resistant to dripping water; however, it should not be exposed to sustained rain. Do not place the sensor on metal objects as these would reduce transmission range. The sensor can be placed vertically or hung on a wall. A sensor with a wired probe can be placed in 2 ways:

1. The sensor is located in a room and the wired probe is led to the outside through a gap in the

window. In that case, the sensor measures outdoor temperature and indoor humidity.

2. The sensor and the wired probe are located outside. In that case, the sensor measures outdoor

temperature and humidity. If the weather station screen shows the low battery icon in eld no. 5, replace the batteries in the sensor. If the weather station screen shows the low battery icon in eld no. 17, replace the batteries in the station. Note: It may take up to 30 minutes since the insertion of batteries into the units before the station begins correctly displaying all measured data and loads DCF time.5 Weather Station RESET If the weather station displays incorrect values or does not respond to button presses, remove the batteries and disconnect the power adapter, then reinsert the batteries and reconnect the adapter. This will erase all data; you will need to set the weather station again. The same method is used to reset the sensor. Changing Sensor Channel and Connecting Additional Sensors The station can be paired with up to 3 wireless sensors.

1. Long-press the CH button on the station; the

icon will start ashing.

2. Remove the battery compartment cover on the back of the sensor and insert alkaline batteries

3. Set the sensor channel number (1, 2, 3) of your choice by repeatedly pressing the CH button.

The channel number will be displayed on the sensor‘s screen next to the humidity value. Data from the sensor will be loaded into the station within 3 minutes. Repeat the whole process if the sensor‘s signal is not detected. Choose the sensor channel number (1, 2, or 3) by repeatedly pressing the CH button. The number will be displayed on the station‘s screen in eld no. 3. Setting the Station to Display Data from Multiple Sensors Press the CH button on the weather station repeatedly to view data from each connected sensor one by one. Radio-Controlled Clock (DCF77) After registering the wireless sensor, the weather station will automatically search for DCF77 signal (hereinafter referred to as DCF) for 7 minutes; the icon will ash depending on the strength of DCF signal. During the search, no other data on the screen will be updated and buttons will be disabled (except SNOOZE/LIGHT). Pressing the DOWN button for 3 seconds cancels the search for DCF signal. Signal detected – the icon stops ashing and the current time and date will be displayed with the icon. Signal not detected – the DCF icon will not be displayed. To repeat the search for DCF signal for 7 minutes, press and hold the DOWN button for 3 seconds. To cancel the search for DCF signal, press and hold the DOWN button again for 3 seconds. DCF signal will be synchronised regularly every day between 01:00 and 05:00. During summer time, the icon will be displayed below the time value. In standard conditions (at safe distance from sources of interference, such as TV sets or computer monitors), the reception of time signal takes several minutes. If the weather station does not detect the signal, follow these steps:

1. Move the weather station to another location and try to detect the DCF signal again.

2. Check the distance of the clock from sources of interference (computer monitors or television

sets). It should be at least 1.5 to 2 m during the reception of signal.

3. When receiving the DCF signal, do not place the weather station near metal doors, window

frames and other metal structures or objects (washing machines, dryers, refrigerators, etc.).

4. In reinforced concrete structures (cellars, high-rise buildings, etc.), the reception of DCF signal

is weaker, depending on the conditions. In extreme cases, place the weather station close to a window in the direction of a transmitter. The reception of the DCF radio signal is aected by the following factors:

• Thick walls and insulation, basements and cellars.

• Inadequate local geographical conditions (these are dicult to assess in advance).

• Atmospheric disturbances, thunderstorms, electrical appliances with no interference elimination, television sets and computers located near the DCF receiver. If the weather station cannot detect the DCF signal, time and date must be set manually. Note: If the weather station detects the DCF signal but the current time on the screen is incorrect (e.g. shifted ±1 hour), you must set the correct time zone for the country where you are using the station, see Manual Setting of Time and Date. The current time will be shown with the appropriate time zone dierence.6 Manual Setting of Time and Date, 12/24 h Time Format, °C/°F Temperature Unit

1. Press and hold the MODE button for 3 seconds.

2. Use the UP or DOWN button to set the following parameters: year – month – day – date display

format – calendar language (GER, FRE, ITA, DUT, SPA, DAN, ENG) – 12/24 h time format – time zone – hour – minute – °C/°F temperature unit. Setting an Alarm The weather station allows you to set 2 separate alarm times. Press the ALARM button repeatedly to view the alarm time for alarm no. 1 (A1) or 2 (A2). Then long-press the ALARM button; the time value will start ashing. Set the time by repeatedly pressing the UP or DOWN button; to navigate in the menu, press the ALARM button again. You can set the time for both alarms this way. To activate alarm no. 1 press the ALARM button 1× to display the time for alarm no. 1 (A1). Press UP or DOWN; will appear on the screen. To deactivate the alarm, press UP or DOWN again; the icon will disappear. To activate alarm no. 2 press the ALARM button 2× to display the time for alarm no. 2 (A2). Press UP or DOWN; will appear on the screen. To deactivate the alarm, press UP or DOWN again; the icon will disappear. The active alarm(s) will then trigger at the set time. Snooze Function Alarm ringing can be postponed by 5 minutes using the SNOOZE/LIGHT button located on the top of the weather station. Press the button when the alarm starts ringing. The alarm icon and Zz icon will be ashing. To cancel SNOOZE mode, press any other button except SNOOZE/LIGHT – the icon will stop ashing and will remain on the screen. The alarm will be re-activated the next day. If you do not press any button while the alarm is ringing, the ringing will stop automatically after 2 minutes. The alarm will trigger again the next day. Station Screen Illumination When powered via adapter: Permanent screen illumination is set automatically. Repeatedly pressing the SNOOZE/LIGHT button will allow you to set 3 dierent modes for permanent illumination (maximum, low, o). When powered only by 3× 1.5 V AAA batteries: Screen illumination is o. Pressing the SNOOZE/LIGHT button will turn screen illumination on for 10 seconds, then it turns o again. When the station is only powered by batteries, permanent screen illumination cannot be activated! Note: The inserted batteries serve as backup for the measured/set data. If batteries are not inserted and you unplug the adapter, all data will be erased. Displaying Maximum and Minimum Temperature and Humidity Readings Repeatedly pressing the UP button will gradually display the maximum (MAX icon) and minimum (MIN icon) temperature and humidity readings. To manually erase the memory of measured values, long press the UP button. The memory of measured values is automatically erased every day at 00:00. Atmospheric Pressure The station displays atmospheric pressure in hPa/inHg in eld no. 11. Moving the weather station to another place will aect the measured values. Measurement will stabilise within 12 hours of battery insertion or station relocation. Setting the Pressure Unit/Pressure Value/Weather Forecast Icon

1. Long-press the SNOOZE/LIGHT button.

Set the pressure unit (hPa, inHg) using the UP and DOWN buttons. Conrm by pressing SNOOZE/LIGHT.7

2. You can then set the pressure value using UP/DOWN.

This value is used to make pressure calculation more accurate. You can nd the pressure value at your location on the Internet, for example. Conrm the value by pressing SNOOZE/LIGHT.

3. The weather forecast icon will start ashing.

Set the icon based on the current weather using UP/DOWN. This is used to make the forecast calculation more accurate. Conrm by pressing SNOOZE/LIGHT. Mould/Dew Point/Heat Indication

1. Press the DOWN button.

An indicator of the risk of indoor mould (MOLD) will appear on the screen: 0 – no risk LOW – low risk MED – medium risk HI – high risk

2. Press the DOWN button 2×.

An indicator of the risk of outdoor mould (MOLD) will appear on the screen: 0 – no risk LOW – low risk MED – medium risk HI – high risk

3. Press the DOWN button 3×.

The outdoor drew point (DEW) value will appear on the screen. Dew point is the temperature at which air becomes fully saturated with water vapour, which then starts condensing in the form of water droplets.

4. Press the DOWN button 4×.

The outdoor heat index (HEAT) will appear on the screen. The value is only displayed if outdoor temperature is over 28°C. Outdoor Clothing Index The icon for recommended clothes changes based on outdoor temperature. It is displayed in eld no. 6. It is displayed separately for each connected sensor. Outdoor temperature <18°C 18°C to 28°C >28°C Heat Index – Smiley Face The heat index combines indoor air temperature and relative air humidity to determine the apparent temperature – also known as felt air temperature. The body normally cools by sweating. Sweat is essentially water that conducts heat away from the body though evaporation. If relative humidity is high, the speed of water evaporation is low and heat dissipates from the body more slowly. As a result, the body retains more heat than it would in a dry environment. Dry environment Comfortable environment Wet environment Humidity <40 % 40–70 % >70 %8 Temperature/Humidity/Pressure (Weather) Trend The icon for outdoor temperature and humidity trend is shown in eld no. 8 and 17. The icon for indoor temperature and humidity trend is shown in eld no. 24 and 22. The pressure trend icon is shown in eld no. 7. Temperature, humidity and pressure trend indicator Falling Constant Rising Moon Phase The moon phase icon is displayed in eld no. 21.

1 – New Moon 2 – Waxing Crescent 3 – Waxing Crescent 4 – First Quarter 5 – Waxing Gibbous 6 – Waxing Gibbous 7 – Full Moon 8 – Waning Gibbous 9 – Waning Gibbous 10 – Last Quarter 11 – Waning Crescent 12 – Waning Crescent Weather Forecast The station uses changes in atmospheric pressure to forecast weather for the next 12–24 hours for an area within the radius of 15–20 km. The accuracy of the weather forecast is approximately 70 %. As the weather forecast may not be 100 % accurate, neither the manufacturer nor the seller can be held responsible for any loss caused by an incorrect forecast. When you rst set or reset the weather station, it takes approximately 12 hours before the weather station begins forecasting correctly. The weather station displays 7weather forecast icons. Note: The currently displayed icon indicates the forecast for the next 12–24 hours. It may not reect the current state of the weather.

1 – Sunny 2 – Slightly cloudy 3 – Cloudy 4 – Rain/Snow at outdoor temperature lower than -1°C 5 – Heavy rain/Snow at outdoor temperature lower than -1°C 6 – Rainstorm/Snowstorm at outdoor tem- perature lower than -1°C Safety Instructions and Warnings Read the user manual before using the device. Follow the safety instructions stated in the manual.9 The product is designed to serve reliably for many years if used properly.

• Read the manual carefully before using this product.

• Do not expose the product to direct sunlight, extreme cold or humidity, and sudden changes in temperature.

• Do not place the product in locations prone to vibration and shocks – may cause damage.

• Do not subject the product to excessive force, impacts, dust, high temperatures or humidity – doing so may cause malfunction, shorten battery life, damage the batteries or deform the plastic parts.

• Do not expose the product to rain or moisture if it is not designed for outdoor use.

• Do not place any open ame sources on the product, e.g. a lit candle, etc.

• Do not place the product in places with inadequate air ow.

• Do not insert any objects in the product‘s vents.

• Do not tamper with the internal electric circuits of the product – doing so may damage the product and will automatically void the warranty.

• To clean the product, use a slightly moistened soft cloth. Do not use solvents or cleaning agents – they could scratch the plastic parts and cause corrosion of the electric circuits.

• Do not submerse the product in water or other liquids or expose it to dripping or splashing water.

• If the product becomes damaged or defective, do not perform any repairs yourself; bring it for repair to the store where you bought it.