HT 65 - Curling iron BEURER - Free user manual and instructions

Product type	Curling iron
Brand	Beurer
Model	HT 65
Weight	Approx. 660 g
Power supply	220–240 V~, 50–60 Hz
Power consumption	120 W
Safety class	II
Ambient temperature range	-10 to +40 °C
Heating temperature	Adjustable, preset to 160 °C
Curl types	Beach Waves, natural curls, Mermaid Waves, waves
Automatic shut-off	Yes, after 30 minutes
Rotation	360°
Suspension ring	Yes
Transport lock	Yes
LED temperature display	Yes
Usage	Only on dry, clean hair
Cleaning	Unplug before cleaning, do not use flammable liquids, avoid water ingress
Included accessories	Curling iron, instruction manual
Warranty	See the provided warranty card

Frequently Asked Questions - HT 65 BEURER

How to use the Beurer HT 65 curling iron?

Dry and brush your hair. Turn on the device with the ON/OFF button. Set the temperature with the + and - buttons. Place a strand between the heating bars, close the handle for a few seconds, then release. Repeat on the entire strand.

What temperature should I choose to curl my hair?

The default temperature is 160 °C. You can adjust it between approximately 120 °C and 200 °C depending on your hair type. Lower temperatures for fine or damaged hair, higher for thick hair.

Does the curling iron turn off automatically?

Yes, the device turns off automatically after 30 minutes. The LED screen flashes 25 minutes after startup to warn you.

Can I use the curling iron on wet hair?

No, use it only on dry hair to avoid damage and risk of electric shock.

How to clean the Beurer HT 65 curling iron?

Unplug the device and let it cool down. Wipe the heating bars and the outer surface with a damp cloth. Do not use flammable products and avoid water entering the interior.

What types of curls can I create?

You can create Beach Waves, natural curls, Mermaid Waves or waves by turning the rotary knob to adjust the barrel size.

Is the curling iron suitable for travel?

Yes, it has a transport lock and a suspension ring. Check the voltage compatibility (220-240 V) with your destination.

What to do if the power cord is damaged?

Do not use the device. Have the cord replaced by the manufacturer, its after-sales service or a qualified person.

Can I use the curling iron in the bathroom?

No, never use it near water (bathtub, shower, sink) to avoid risk of electric shock. Unplug it after each use.

How to store the curling iron after use?

Turn off the device, unplug it and let it cool on a heat-resistant surface. Store it in a dry place out of reach of children. You can hang it by the ring.

USER MANUAL HT 65 BEURER

Exterior view of a black and white electric hair curler (no text or symbols visible)

EN Wave stylist Instructions for use.....13

Illustration of a folded document or book with a geometric shape on the left, showing text lines and page layout (no readable text or symbols)

EN Unfold page 3 before reading the instructions for use.

Line drawing of a hand gripping a mechanical tool (no text or symbols)

Line drawing of a hand holding a tool with a tool tip, no text or symbols present

Beach Waves

Simple line drawing of a mechanical component with a circular top and two protruding ports (no text or symbols)

Line drawing of a woman with long hair (no text or symbols)

Natürliche Wellen

Simple line drawing of a mechanical component with a central circular feature and two protruding ports (no text or symbols)

Line drawing of a woman with long wavy hair (no text or symbols)

Read these instructions for use carefully. Observe the warnings and safety notes. Keep these instructions for use for future reference. Make the instructions for use accessible to other users. If the device is passed on, provide the instructions for use to the next user as well.

Included in delivery

Check that the exterior of the cardboard delivery packaging is intact and make sure that all contents are present. Before use, ensure that there is no visible damage to the device or accessories and that all packaging material has been removed. If you have any doubts, do not use the device and contact your retailer or the specified Customer Service address.

1 x Wave styler
1 x Set of these instructions for use

Table of contents

1. Signs and symbols...... 15
2. Intended use....16
3. Device description......16

4. Usage 17
   4.1 Starting the application......17
   4.2 After use....20

5. Cleaning and maintenance.....20

6. Disposal......21
7. Technical data 21
8. Warranty 21

WARNING

- The device is only intended for domestic/private use, not for commercial use.

- This device may be used by children over the age of 8 and by people with reduced physical, sensory or mental skills or a lack of experience or knowledge, provided that they are supervised or have been instructed on how to use the device safely, and are fully aware of the consequent risks of use.

• Children must not play with the device.

- Cleaning and user maintenance must not be performed by children unless supervised.

- If the mains connection cable of this device is damaged, it must be replaced by the manufacturer, its customer service department or a similarly qualified person to avoid any risk.

- When using the device in the bathroom, unplug the mains plug after use, as water in the vicinity constitutes a danger, even when the device is switched off.

- Never use the device near baths, wash basins, showers or other objects containing water or other liquids – risk of electric shock!

- As an additional safety measure, we recommend the installation of a residual-current circuit device (RCD). The rated operational current should not exceed 30 mA in the bathroom circuit. Your local electrical specialist can provide you with the relevant information.

1. SIGNS AND SYMBOLS

The following symbols are used on the device, in these instructions for use, on the packaging and on the type plate for the device:

	Warning	This device must not be used near water or in water (e.g. in a wash basin, or in the shower or bath) – risk of electric shock!
	Warning	Warning notice indicating a risk of injury or damage to health
	Important	Safety note indicating possible damage to the device/accessory
	Note Important information to note
	Protection class II
	Dispose of packaging in an environmentally friendly manner
	Disposal in accordance with the Waste Electrical and Electronic Equipment EC Directive – WEEE
	Read the instructions for use
	CE labellingThis product satisfies the requirements of the applicable European and national directives.
	United Kingdom Conformity Assessed Mark
	Manufacturer

2. INTENDED USE

The wave styler must only be used by individuals for shaping and styling and is for personal use only! Do not use the wave styler on synthetic hair or on animals.

Warning

The device is suitable only:

• for external use.
• for the intended purpose and as specified in these instructions for use.

Any improper use may be dangerous!

3. DEVICE DESCRIPTION

1 Dial for setting the wave size	7 Handle
2 Heating rods	8 360° swivel joint
3 + Button for increasing the temperature	9 Hanging loop
4 - Button for reducing the temperature	10 Mains cable
5 ON/OFF button ➊	11 Transport lock
6 LED temperature display (°C)

4. USAGE

4.1 Starting the application

1. Dry your hair thoroughly before using the wave styler.
2. Make sure that your hair is clean and free from styling products. This excludes special products designed to help your hair when shaping curls or waves.
3. Comb your hair to get rid of any tangles.
4. Switch on the wave styler by pressing the ON/OFF button [5].
5. To make it easier to set the temperature, first close the wave styler and slide the transport lock [12] to the position. Set your desired temperature setting using the - button [3] or + button [4]. The device is pre-set to 160°C when it is switched on. Once you have set the temperature, slide the transport lock [12] to the position. The respective temperature setting starts to flash white in the LED temperature display [6]. Once the temperature setting lights up white permanently, the heating rods [2] have reached the configured temperature setting and the wave styler is ready for use.
6. Separate your hair into individual sections with a width of approx. 2-4 cm. Hold the strands taut.
7. Place the section of hair between the heating rods [2] starting at the roots. Make sure that you do not touch your scalp with the heating rods [2].
i NoteTurn the rotary wheel [1] to set the desired wave size created by the middle heating rod.The following styles can be set:
Beach waves
Natural waves

Mermaid waves
Water waves
8. Press the handle [7] of the wave styler shut so that the hair section is enclosed by the heating rods. Exert a small amount of pressure and hold this position for a few seconds.
9. Release the handle [7] of the wave styler. Place the wave styler a little lower on the hair section so that the part that has already been styled is not done again. Repeat the application along the entire length of the hair section.

Note

The wave styler features a safety switch-off function. After approx. 25 minutes, the LED temperature display starts to flash [6] to remind you about the automatic switch-off. If you want to use the wave styler for longer than 30 minutes, switch the device off and then immediately on again. The safety switch-off function is then reset to activate again in 30 minutes.

4.2 After use

1. To switch off the wave styler after use, hold down the ON/OFF button①[5] for three seconds. The heating rods [2] are now switched off and the LED temperature display [6] goes out.
2. Pull the mains plug [11] out of the socket after each use. Do not wind the mains cable [10] around the device!
3. Place the wave styler on a stable, horizontal and non-flammable surface to cool down. Make sure that the hot heating rods [2] do not touch the surface! Risk of fire!
4. Wait until the heating rods [2] of the wave styler have cooled down completely. Then store the wave styler in a dry place out of the reach of children. Alternatively, you can hang up the wave styler on a hook using the hanging eyelet [9].

5. CLEANING AND MAINTENANCE

Important

• Always pull the mains plug out of the socket before cleaning the device. Risk of electric shock!
• Do not clean the wave styler with highly flammable liquids. Risk of fire!

Warning

- Ensure that no water gets inside the device! Risk of electric shock!

6. DISPOSAL

For environmental reasons, do not dispose of the device in household waste at the end of its service life. Dispose of the device at a suitable local collection or recycling point in your country. Observe the local regulations for material dispos-

al. Dispose of the device in accordance with EC Directive – WEEE (Waste Electrical and Electronic Equipment).

If you have any questions, please contact the local authorities responsible for waste disposal.

You can obtain the location of collection points for old devices from the local or municipal authorities, local waste disposal company or your dealer, for example.

7. TECHNICAL DATA

Weight: Approx. 660 g
Voltage supply 220-240 V~, 50-60 Hz
Power consumption 120 W
Protection class	II
Ambient conditions Only approved for indoors
Permissible temperature range	-10 to +40°C

Subject to technical changes.

8. WARRANTY

Further information on the warranty and warranty conditions can be found in the warranty leaflet supplied.

FRANÇAIS

Line drawing of a person holding a tool, no text or symbols present

i Remarque

Line drawing of a hand gripping a mechanical tool or tool (no text or symbols present)

i Nota

Line drawing of a hand holding a tool with a tool tip, no text or symbols present

Simple line drawing of a mechanical component with a central circular feature and two protruding ports (no text or symbols)

Line drawing of a woman with long hair (no text or symbols)

Ondulado natural

Simple line drawing of a mechanical component with a central circular feature and two protruding ports (no text or symbols)

Line drawing of a woman with long wavy hair (no text or symbols)

Line drawing of a person holding a tool, no text or symbols present

i Indicazione

Line drawing of a hand gripping a mechanical tool (no text or symbols)

Line drawing of a hand holding a tool with a brush tip, no text or symbols present

Kumsal dalgası

Simple line drawing of a mechanical component with a circular top and two protruding ports (no text or symbols)

Line drawing of a woman with long hair (no text or symbols)

Doğal dalga

Simple line drawing of a mechanical component with a central circular feature and two protruding ports (no text or symbols)

Line drawing of a woman with long wavy hair (no text or symbols)

Line drawing of a hand gripping a mechanical tool or clamp (no text or symbols)

i Указание

Line drawing of a hand holding a tool with a screwdriver inserted (no text or symbols)

Simple line drawing of a mechanical component with a central circular feature and two protruding ports (no text or symbols)

Line drawing of a woman with long hair (no text or symbols)

естественные волны

Simple line drawing of a mechanical component with a central circular feature and two protruding ports (no text or symbols)

Line drawing of a woman with long wavy hair (no text or symbols)

Line drawing of a hand gripping a mechanical tool (no text or symbols)

Line drawing of a hand holding a tool with a brush tip, partially enclosed by a pencil (no text or symbols)

Beach waves

Simple line drawing of a mechanical component with a circular end and two protruding ports (no text or symbols)

Line drawing of a woman with long hair (no text or symbols)

Naturalne fale

Simple line drawing of a mechanical component with a central circular feature and two protruding ports (no text or symbols)

Line drawing of a woman with long wavy hair (no text or symbols)

3. BESCHRIJVING VAN HET APPARAAT

Line drawing of a person holding a tool, no text or symbols present

i Aanwijzing

Line drawing of a hand gripping a mechanical tool (no text or symbols)

Line drawing of a hand holding a tool with a screwdriver inserted (no text or symbols)

Beach Waves

Simple line drawing of a mechanical component with a circular top and two protruding ports (no text or symbols)

Line drawing of a woman with long hair (no text or symbols)

Naturlige bølger

Simple line drawing of a mechanical component with a central circular feature and two protruding ports (no text or symbols)

Line drawing of a woman with long wavy hair (no text or symbols)

United Kingdom Conformity Assessed Mark

Tillverkare

2. AVSEDD ANVÄNDNING

Line drawing of a hand gripping a mechanical tool (no text or symbols)

Line drawing of a hand holding a tool with a brush tip, partially enclosed in a pencil holder (no text or symbols)

Beach Waves

Simple line drawing of a mechanical component with a circular top and two protruding ports (no text or symbols)

Line drawing of a woman with long hair (no text or symbols)

Naturliga vågor

Simple line drawing of a mechanical component with a central circular feature and two protruding ports (no text or symbols)

Line drawing of a woman with long wavy hair (no text or symbols)

Line drawing of a hand gripping a mechanical tool (no text or symbols)

Line drawing of a hand holding a tool with a brush tip, alongside a separate tool (no text or symbols present)

Strandkrøller

Simple line drawing of a mechanical component with a circular end and two protruding ports (no text or symbols)

Line drawing of a woman with long hair (no text or symbols)

Naturlige bølger

Simple line drawing of a mechanical component with a central circular feature and two protruding ports (no text or symbols)

Line drawing of a woman with long wavy hair (no text or symbols)

Havfruekrøller
Vannbølger
8. Lukk krølltangen med håndtaket [7], slik at håret omsluttes av varmestavene. Bruk litt trykk, og hold posisjonen i et par sekunder.
9. Slipp håndtaket [7] på krølltangen. Plasser så krølltangen litt lenger ned på håret, slik at den allerede behandlede delen ikke behandles på nytt. Gjenta behandlingen på hele lengden.

i Merknad

Line drawing of a hand gripping a mechanical tool (no text or symbols)

Line drawing of a hand holding a tool with a screwdriver inserted (no text or symbols)

Beach Waves

Simple line drawing of a mechanical component with a circular top and two protruding ports (no text or symbols)

Line drawing of a woman with long hair (no text or symbols)

Simple line drawing of a mechanical component with a central circular feature and two protruding ports (no text or symbols)

Line drawing of a woman with long wavy hair (no text or symbols)