Q: What does the red filter indicator of the BEURER LR 220 mean and how do I reset it?

The red filter indicator lights up automatically after 4,260 hours of operation to indicate that the filter has reached the end of its useful life. The filter cannot be regenerated and must be replaced. Replace the filter Turn off and unplug the device Unscrew the rotary closure under the casing Remove the used filter Install the new filter (reference 680.07) - three-layer combined filter (pre-filter, HEPA H13, activated carbon) Close the bottom of the casing Plug the device back in Reset the indicator Once the new filter is installed, press and hold the ON/OFF button for 20 seconds until the red indicator turns off. The device is then ready to operate. Maintenance tip: Although the filter cannot be washed, you can dust its exterior monthly with a vacuum cleaner to maintain filtration performance.

Q: How to connect the electrodes to the cables of the BEURER EM49 electrostimulator?

The BEURER EM49 uses a simple connection with clip fasteners to attach the electrodes to the cables. Here’s how to proceed: The electrodes connect directly to the cables via clip connectors. The cables are then plugged into the port located on the top of the device . Once the cables are connected to the device, you can place the electrodes on the desired stimulation areas. Important: Handle the cables carefully - do not pull, twist, or excessively bend them, as this could damage them and compromise the quality of stimulation.

Q: What does error code E3 mean on the BEURER BC 85?

The error code E3 on your BEURER BC 85 means that the cuff is too tight or not tight enough around your arm. How to correct this issue: Loosen or tighten the cuff as needed - it should be snug but not constricting. You should be able to slide a finger between the cuff and your skin. The cuff of the BEURER BC 85 is suitable for arms with a circumference of 135 to 230 mm. Check that the positioning corresponds to your body shape. Place the cuff directly on the skin or over a thin fabric, at heart level. Restart the measurement while remaining still and silent during the entire inflation and measurement process. If the E3 code persists despite correct adjustment of the cuff, the issue may also be related to movement during the measurement. Make sure not to move or speak during the blood pressure reading (code E2 may also appear in this case).

Q: How to replace the cuff of the BEURER BM 59 blood pressure monitor?

The manual for the BEURER BM 59 confirms that replacement parts and accessories are available, but it does not provide the detailed procedure for replacing the cuff. Size and compatibility The original cuff of the BEURER BM 59 is suitable for a arm circumference of 22 to 42 cm . If you need a replacement cuff, make sure it is compatible with this size range. Where to find a replacement cuff Compatible replacement cuffs for your BEURER BM 59 are available: On the official website www.beurer.de , in the “Service” section From BEURER customer service (provide your device's serial number) On authorized BEURER distributor websites BEURER service can confirm the exact reference of the cuff to order and installation instructions if necessary.

Question 1

What do the exclamation points displayed on the Beurer EM 95 Bluetooth mean?

Accepted Answer

The flashing exclamation points on the screen indicate a loss of contact at one of the electrodes.

According to the Beurer EM 95 manual, when an electrode detaches, the electrical circuit is interrupted and the intensity of the affected channel returns to zero. The device then emits a sound signal and displays a flashing exclamation point on the intensity display of that channel.

Solutions

Check that all adhesive electrodes (45 x 45 mm) are properly attached and adhere well to the skin
Clean the skin before application to ensure better adhesion
If an electrode has come off, reattach it firmly and the display should return to normal
Note that electrodes gradually lose their adhesive capacity over time. The manual recommends replacing them every 20 uses at most
If the electrodes are worn, obtain replacement adhesive electrodes of 45 x 45 mm

The exclamation point will disappear automatically once the electrical contact is restored.

Question 2

What does the red filter indicator of the BEURER LR 220 mean and how do I reset it?

Accepted Answer

The red filter indicator lights up automatically after 4,260 hours of operation to indicate that the filter has reached the end of its useful life. The filter cannot be regenerated and must be replaced.

Replace the filter

Turn off and unplug the device
Unscrew the rotary closure under the casing
Remove the used filter
Install the new filter (reference 680.07) - three-layer combined filter (pre-filter, HEPA H13, activated carbon)
Close the bottom of the casing
Plug the device back in

Reset the indicator

Once the new filter is installed, press and hold the ON/OFF button for 20 seconds until the red indicator turns off. The device is then ready to operate.

Maintenance tip: Although the filter cannot be washed, you can dust its exterior monthly with a vacuum cleaner to maintain filtration performance.

Question 3

How do I pair the BEURER BF 451 scale with my phone?

Accepted Answer

Pairing Steps

The BEURER BF 451 scale connects via Bluetooth with the beurer HealthManager Pro app (available for free on the App Store and Google Play).

Download the beurer HealthManager Pro app on your phone
Enable Bluetooth on your smartphone
Open the app and follow the instructions to add a device
Press briefly on the scale platform to display 0.0 kg - the app will automatically detect it
Accept the pairing request if a notification appears

If pairing does not work

Try these solutions:

Ensure the scale is within 10 meters of your phone
Turn Bluetooth off and then back on your phone
Completely close the app and restart it
In your phone's Bluetooth settings, remove the scale and then re-add it via the beurer HealthManager Pro app

Once paired, the scale will automatically sync your measurements with the app. It can store up to 8 different user profiles.

Question 4

The message 'Low' appears even after changing the batteries - how to resolve?

Accepted Answer

If your BEURER BF 195 scale displays 'Low' (low battery) even after installing two new CR2032 batteries, check the following points:

Correct battery orientation: The two CR2032 batteries must be inserted in the correct direction (positive pole facing up). A reversed or improperly positioned battery prevents the battery signal from resetting.
Electrical contact: Lightly clean the metal contacts in the battery compartment with a dry cloth to ensure a good connection. Dust or corrosion can keep the 'Low' message displayed.
Battery quality: Ensure that the CR2032 batteries are truly new and of good quality. Low-quality or partially used batteries may not stabilize the system properly.
Reset after replacement: After changing the batteries, leave the scale without batteries for a few seconds, then reinsert them. This may force the battery sensor to reset.

If the 'Low' message persists after these checks, it is possible that the battery detection circuit is faulty and the scale may require repair.

Question 5

How to connect the electrodes to the cables of the BEURER EM49 electrostimulator?

Accepted Answer

The BEURER EM49 uses a simple connection with clip fasteners to attach the electrodes to the cables. Here’s how to proceed:

The electrodes connect directly to the cables via clip connectors.
The cables are then plugged into the port located on the top of the device.
Once the cables are connected to the device, you can place the electrodes on the desired stimulation areas.

Important: Handle the cables carefully - do not pull, twist, or excessively bend them, as this could damage them and compromise the quality of stimulation.

Question 6

What does error code E3 mean on the BEURER BC 85?

Accepted Answer

The error code E3 on your BEURER BC 85 means that the cuff is too tight or not tight enough around your arm.

How to correct this issue:

Loosen or tighten the cuff as needed - it should be snug but not constricting. You should be able to slide a finger between the cuff and your skin.
The cuff of the BEURER BC 85 is suitable for arms with a circumference of 135 to 230 mm. Check that the positioning corresponds to your body shape.
Place the cuff directly on the skin or over a thin fabric, at heart level.
Restart the measurement while remaining still and silent during the entire inflation and measurement process.

If the E3 code persists despite correct adjustment of the cuff, the issue may also be related to movement during the measurement. Make sure not to move or speak during the blood pressure reading (code E2 may also appear in this case).

Question 7

How to replace the cuff of the BEURER BM 59 blood pressure monitor?

Accepted Answer

The manual for the BEURER BM 59 confirms that replacement parts and accessories are available, but it does not provide the detailed procedure for replacing the cuff.

Size and compatibility

The original cuff of the BEURER BM 59 is suitable for a arm circumference of 22 to 42 cm. If you need a replacement cuff, make sure it is compatible with this size range.

Where to find a replacement cuff

Compatible replacement cuffs for your BEURER BM 59 are available:

On the official website www.beurer.de, in the “Service” section
From BEURER customer service (provide your device's serial number)
On authorized BEURER distributor websites

BEURER service can confirm the exact reference of the cuff to order and installation instructions if necessary.

Question 8

How to check that the red electrodes are properly connected to the BEURER EM 59 muscle stimulator?

Accepted Answer

To check that the red electrodes are properly connected to your BEURER EM 59 stimulator, follow these simple and practical checks.

Mechanical checks: Ensure that the connectors of the red electrode cables are firmly inserted into the connection ports located at the bottom of the device. Also, check that the gel pads adhere firmly to the electrodes and are placed on clean, dry skin, as poor adhesion can create a false contact.

Immediate practical test: This is the best way to check the connection. Turn on the device by pressing the ON/OFF button, select any program, and then gradually adjust the intensity of channel 1 (red electrodes) using the adjustment buttons. If the electrodes are properly connected, you will feel a gradual stimulation. If you feel nothing, the connection is faulty.

Alert signal: If an electrode comes off or disconnects during use, the device automatically reduces the intensity of the impulses to the minimum for all channels. If you notice that the intensity rises back to the minimum on its own without any action on your part, or that the intensity change does not correspond to your adjustments, this indicates a connection problem.

Additional checks: Inspect the connectors at the base of the device for any signs of corrosion, dirt, or damage. Ensure that the cables are not excessively bent or twisted, as this could damage the internal connections. If the gel pads are worn or dry, replace them, as they play a crucial role in conducting electricity.

Question 9

Why does the BEURER EM 59 muscle stimulator have 2 red electrodes and 2 gray electrodes?

Accepted Answer

The BEURER EM 59 muscle stimulator is equipped with 4 electrodes, including 2 red and 2 gray, to allow for very flexible use of its two independent stimulation channels. The red electrodes correspond to channel 1, while the gray electrodes correspond to channel 2.

This configuration allows for the simultaneous treatment of two different areas of the body with completely independent settings. For example, you can stimulate your back with the red electrodes (channel 1) and your legs with the gray electrodes (channel 2) at the same time. Each channel has its own adjustable intensity from 0 to 99 levels, allowing you to tailor the stimulation precisely to the specific needs of each treated area.

For optimal treatment: The manual recommends using all 4 electrodes simultaneously, especially for the massage function of the device. Position the two electrodes of one channel to frame the area to be treated, then do the same with the two electrodes of the second channel. This maximizes the effectiveness of the stimulation.

Practical advantages: This dual-channel configuration saves time during your sessions, as you treat two areas at the same time, with the ability to independently adjust the intensity of each channel and select from the 6 available stimulation programs. This provides you with complete customization tailored to each muscle area.

Question 10

How to correctly position the electrodes on the BEURER EM 59 muscle stimulation device?

Accepted Answer

The positioning of the electrodes is crucial for effective and safe muscle stimulation with the BEURER EM 59. To achieve the desired effect, it is important to place the electrodes wisely. We recommend defining the optimal positions of the electrodes in the desired application area with your doctor.

Distance between the electrodes

The distance between the two electrodes directly influences the volume of tissue stimulated and the strength of stimulation. The greater the distance, the larger the volume of tissue stimulated, but the less intense the stimulation will be. Follow this guideline for choosing the distance:

Most advisable distance: about 5 to 15 cm
Below 5 cm: superficial structures are strongly stimulated
Above 15 cm: deep structures are very weakly stimulated (increase intensity if necessary)

Orientation of the electrodes relative to the muscle fibers

Adapt the direction of current flow to the arrangement of the muscle fibers according to the targeted muscle layer. To stimulate superficial muscles, place the electrodes parallel to the muscle fibers (configuration A-B/C-D). Conversely, if you are targeting deep tissues, position the electrodes perpendicularly to the fibers, for example in a cross (configuration A-D/B-C).

Positioning for pain treatment (TENS mode)

When treating pain with the BEURER EM 59 and its 2 separately adjustable channels, arrange the electrodes of one channel so that the painful point is located between them. Otherwise, place one electrode directly on the painful point and the other electrodes at least 2 or 3 cm away from this point. The electrodes of the second channel can simultaneously treat other painful points or encircle the painful area with a cross arrangement.

Additional tips

For the massage function: always use all 4 electrodes for optimal treatment
Skin preparation: use the electrodes on clean skin, preferably hairless and non-greasy. Clean and shave the skin before application if necessary
In case of detachment: if an electrode comes off during use, the intensity of the impulses will drop to minimum. Reattach the electrode and readjust the impulse intensity

User manual BEURER : user manuals and guides in PDF

Models BEURER most viewed

Browse manuals BEURER by appliance type

Recent questions about devices BEURER