Question 1

How to check that the red electrodes are properly connected to the BEURER EM 59 muscle stimulator?

Accepted Answer

To check that the red electrodes are properly connected to your BEURER EM 59 stimulator, follow these simple and practical checks.

Mechanical checks: Ensure that the connectors of the red electrode cables are firmly inserted into the connection ports located at the bottom of the device. Also, check that the gel pads adhere firmly to the electrodes and are placed on clean, dry skin, as poor adhesion can create a false contact.

Immediate practical test: This is the best way to check the connection. Turn on the device by pressing the ON/OFF button, select any program, and then gradually adjust the intensity of channel 1 (red electrodes) using the adjustment buttons. If the electrodes are properly connected, you will feel a gradual stimulation. If you feel nothing, the connection is faulty.

Alert signal: If an electrode comes off or disconnects during use, the device automatically reduces the intensity of the impulses to the minimum for all channels. If you notice that the intensity rises back to the minimum on its own without any action on your part, or that the intensity change does not correspond to your adjustments, this indicates a connection problem.

Additional checks: Inspect the connectors at the base of the device for any signs of corrosion, dirt, or damage. Ensure that the cables are not excessively bent or twisted, as this could damage the internal connections. If the gel pads are worn or dry, replace them, as they play a crucial role in conducting electricity.

Question 2

Why does the BEURER EM 59 muscle stimulator have 2 red electrodes and 2 gray electrodes?

Accepted Answer

The BEURER EM 59 muscle stimulator is equipped with 4 electrodes, including 2 red and 2 gray, to allow for very flexible use of its two independent stimulation channels. The red electrodes correspond to channel 1, while the gray electrodes correspond to channel 2.

This configuration allows for the simultaneous treatment of two different areas of the body with completely independent settings. For example, you can stimulate your back with the red electrodes (channel 1) and your legs with the gray electrodes (channel 2) at the same time. Each channel has its own adjustable intensity from 0 to 99 levels, allowing you to tailor the stimulation precisely to the specific needs of each treated area.

For optimal treatment: The manual recommends using all 4 electrodes simultaneously, especially for the massage function of the device. Position the two electrodes of one channel to frame the area to be treated, then do the same with the two electrodes of the second channel. This maximizes the effectiveness of the stimulation.

Practical advantages: This dual-channel configuration saves time during your sessions, as you treat two areas at the same time, with the ability to independently adjust the intensity of each channel and select from the 6 available stimulation programs. This provides you with complete customization tailored to each muscle area.

Question 3

How to correctly position the electrodes on the BEURER EM 59 muscle stimulation device?

Accepted Answer

The positioning of the electrodes is crucial for effective and safe muscle stimulation with the BEURER EM 59. To achieve the desired effect, it is important to place the electrodes wisely. We recommend defining the optimal positions of the electrodes in the desired application area with your doctor.

Distance between the electrodes

The distance between the two electrodes directly influences the volume of tissue stimulated and the strength of stimulation. The greater the distance, the larger the volume of tissue stimulated, but the less intense the stimulation will be. Follow this guideline for choosing the distance:

Most advisable distance: about 5 to 15 cm
Below 5 cm: superficial structures are strongly stimulated
Above 15 cm: deep structures are very weakly stimulated (increase intensity if necessary)

Orientation of the electrodes relative to the muscle fibers

Adapt the direction of current flow to the arrangement of the muscle fibers according to the targeted muscle layer. To stimulate superficial muscles, place the electrodes parallel to the muscle fibers (configuration A-B/C-D). Conversely, if you are targeting deep tissues, position the electrodes perpendicularly to the fibers, for example in a cross (configuration A-D/B-C).

Positioning for pain treatment (TENS mode)

When treating pain with the BEURER EM 59 and its 2 separately adjustable channels, arrange the electrodes of one channel so that the painful point is located between them. Otherwise, place one electrode directly on the painful point and the other electrodes at least 2 or 3 cm away from this point. The electrodes of the second channel can simultaneously treat other painful points or encircle the painful area with a cross arrangement.

Additional tips

For the massage function: always use all 4 electrodes for optimal treatment
Skin preparation: use the electrodes on clean skin, preferably hairless and non-greasy. Clean and shave the skin before application if necessary
In case of detachment: if an electrode comes off during use, the intensity of the impulses will drop to minimum. Reattach the electrode and readjust the impulse intensity

Question 4

Can conductive gel be used with the electrodes of the BEURER EM 59 muscle stimulation device?

Accepted Answer

Yes, you can use conductive gel with the electrodes of the BEURER EM 59. The conductive gel enhances the electrical conductivity between the skin and the electrodes, thereby optimizing the transmission of electrical impulses from the device. However, the BEURER EM 59 comes with 4 electrodes that already include built-in gel pads, specifically designed for this model.

Using conductive gel:

You can apply additional conductive gel on the skin before placing the electrodes, or directly on the gel pads to improve electrical contact.
Ensure that the conductive gel used is compatible with muscle stimulation devices and does not damage the gel pads.
The conductive gel should not contain abrasive or corrosive chemical ingredients that could alter the electrodes.

Maintaining the electrodes:

To extend the lifespan of the gel pads (replaceable after about 20 uses), gently clean them after each use with a non-linting damp cloth under lukewarm water and carefully pat them dry. Before cleaning with water, disconnect the connection cable from the device. Ensure that the skin is clean, hair-free, and not greasy before each application.

Important: To maintain the warranty of the BEURER EM 59, only use the original accessories provided or available from Beurer. Using non-original accessories will void the warranty.

Question 5

How to adjust the intensity on the BEURER EM 59 muscle stimulation device?

Accepted Answer

To adjust the intensity on the BEURER EM 59, follow these steps:

Turn on the device by holding the power button until the screen lights up.
Use the '+' and '-' buttons located on the control panel to increase or decrease the intensity of the pulses.
The device offers 99 intensity levels, from 0 to 99, which you can adjust according to your comfort.

If you are unable to change the intensity, check the following points:

Ensure that the electrodes are properly positioned and in direct contact with the skin, as poor contact may prevent adjustment.
Check that the batteries are correctly inserted and sufficiently charged.
Confirm that the device is turned on.

By following these tips, you should be able to adjust the intensity without difficulty.

Question 6

How to disable the sound beep on the BEURER EM49 electrostimulator?

Accepted Answer

According to the official manual of the BEURER EM49, the device does not offer a function to disable sound signals. These beeps are an integral part of the device's confirmation system and cannot be removed via a menu or settings.

The sound signals of the BEURER EM49:

A brief sound signal when you press a valid button (confirmation of command reception)
Two brief sound signals when you press an invalid button or at the wrong time (error alert)
A long sound signal to confirm the activation or deactivation of the Doctor function

Why these signals cannot be disabled: The acoustic signals are built-in safety functions that allow the user to confirm that the device has properly registered each action. This is particularly important during electrostimulation to avoid setting errors.

If you find the beeps too loud, you can reduce the ambient volume during use, or contact Beurer customer service to learn about options available on other models.

User manual BEURER Muscle stimulator : user manuals and guides in PDF

Models BEURER Muscle stimulator most viewed

Other categories BEURER

Recent questions about Muscle stimulator BEURER