GECM 43 Li M Kit - Electric mower EINHELL - Free user manual and instructions
Find the device manual for free GECM 43 Li M Kit EINHELL in PDF.
| Product type | Cordless electric lawn mower |
| Brand | Einhell |
| Model | GECM 43 Li M Kit |
| Cutting width | 43 cm |
| Cutting height | 25-75 mm, adjustable in 6 steps |
| Collection bag volume | 63 liters |
| Weight | 16 kg |
| Power supply | 2 lithium-ion batteries 18 V, 4.0 Ah |
| Charger | Input 200-250 V ~ 50-60 Hz, output 20 V DC, 3.0 A |
| Motor rotation speed | 3000 rpm |
| Sound pressure level (LpA) | 68.1 dB(A) |
| Guaranteed sound power level | 90 dB(A) |
| Vibration on handlebar | 2.5 m/s² |
| Protection type | IPX1 |
| Mulching function | Yes, with included adapter |
| Cutting height adjustment | External lever, 6 positions |
| Safety | Start lock, contact plug |
| Kit contents | 2 batteries, 2 chargers, blade change key, mulching adapter |
| Maintenance and cleaning | Damp cloth, no pressurized water |
| Wear parts | Blade, batteries |
| Warranty | 24 months |
Frequently Asked Questions - GECM 43 Li M Kit EINHELL
User questions about GECM 43 Li M Kit EINHELL
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Electric mower in PDF format for free! Find your manual GECM 43 Li M Kit - EINHELL and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. GECM 43 Li M Kit by EINHELL.
USER MANUAL GECM 43 Li M Kit EINHELL
When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care. Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.
Explanation of the warning signs on the equipment (see Fig. 16)
- Read the directions for use before operating the equipment.
- Keep your distance!
- Caution: Sharp blades! Pull out the safety plug before carrying out any repair work or if the power cable is damaged. The blades will continue to rotate after the motor is switched off.
- Protect the equipment from rain and damp conditions
- Guaranteed sound power level: 90 dB
- Dispose of batteries correctly
1. Safety regulations
The corresponding safety information can be found in the enclosed booklet.
Warning!
Read all the safety information, instructions, illustrations and technical data provided on or with this power tool. Failure to adhere to the following instructions may result in electric shock, fire and/or serious injury.
Keep all the safety information and instructions in a safe place for future use.
Children are not allowed to use this equipment. Children are not allowed to carry out cleaning or maintenance. This equipment can be used by people with limited physical, sensory or mental capacities or those with no experience and knowledge if they are supervised or have received instruction in how to use the equipment safely and understand the dangers which result from such use. Children are not allowed to play with the equipment.
2. Layout and items supplied
2.1 Layout (Fig. 1/2)
- ON/OFF switch
- Top push bar
- Push bar bracket
- Carry handle
- Grass basket
- Cutting height adjustment
- Ejector fl ap
- Safety lock-off
- Washer
- Nuts for top and bottom push bar with quick clamping function
- Safety plug
- Cable clips
- Battery
- Grass basket, bottom part of the housing
- Level indicator
- Grass box, top part of the housing
- Grass basket, front part of the housing
- Charging unit
- Fastening screws for top push bar
- Key for changing the blade
- Mulching adapter
2.2 Items supplied and unpacking (Fig. 2)
Please check that the article is complete as specified in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions.
- Open the packaging and take out the equipment with care.
- Remove the packaging material and any packaging and/or transportation braces (if available).
Check to see if all items are supplied. - Inspect the equipment and accessories for transport damage.
If possible, please keep the packaging until the end of the guarantee period.
Danger!
The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of swallowing or suffocating!
GB
Items supplied
- Cordless lawn mower
- Push bar bracket (2x)
Grass basket - Washers (2x)
- Nuts for top and bottom push bar with quick clamping function (2x)
Safety plug
Cable clips (3x)
Battery (2x) - Charging unit (2x)
Fastening screws for top push bar (2x) - Mulching adapter
Key for changing the blade
Original operating instructions
Safety information
3. Proper use
The lawn mower is intended for private use i.e. for use in home and gardening environments.
Private use of the lawn mower refers an annual operating time generally not exceeding that of 50 hours, during which time the equipment is primarily used to maintain small-scale, residential lawns and home/hobby gardens. Public facilities, sporting halls, and agricultural/forestry applications are excluded.
Important. Due to the high risk of bodily injury to the user, the lawn mower may not be used to trim bushes, hedges or shrubs, to cut scaling vegetation, planted roofs, or balcony-grown grass, to clean (suck up) dirt and debris off walkways, or to chop up tree or hedge clippings. Moreover, the lawn mower may not be used as a power cultivator to level out high areas such as molehills.
For safety reasons, the lawn mower may not be used as a drive unit for other work tools or toolkits of any kind, unless they have been expressly permitted by the manufacturer.
The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.
Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial businesses or for equivalent purposes.
4. Technical data
Motor speed: 3000 min
Protection class: III
Weight: 16kg
Cutting width: 43 cm
Grass basket volume: 63 liters
Sound pressure level L_p .. 68.1 dB(A)
Uncertainty Ka: 3dB
Sound power level L_wA .. 88.1 dB(A)
Cutting height adjustment:.....25-75 mm; 6 levels
Protection type: IPX1
2x Lithium-ion battery
Voltage: 18 V DC
Capacity: 4.0 Ah
Number of cells: 10
2x Battery charger
Input voltage: 200-250 V ~ 50-60 Hz
Output voltage: 20 V DC
Output current: 3.0 A
Protection class: ./回
Sound and vibration values were measured in accordance with the standards EN ISO 3744:1995, ISO 11094:1991 and EN ISO 20643:2008.
Keep the noise emissions and vibrations to a minimum.
Only use appliances which are in perfect working order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
- Have the appliance serviced whenever necessary.
- Switch the appliance off when it is not in use.
Wear protective gloves.
Residual risks
Even if you use this electric power tool in accordance with the instructions, certain
GB
residual risks cannot be eliminated. The following hazards may arise in connection with the equipment's construction and layout:
- Lung damage if no suitable protective dust mask is used.
- Damage to hearing if no suitable ear protection is applied.
Warning!
This equipment generates an electromagnetic fi eld during operation. Under certain circumstances this fi eld may actively or passively impede medical implants. To reduce the risk of serious or fatal injuries, we recommend persons with medical implants to consult their doctor and the manufacturer of the medical implant prior to using the equipment.
5. Before starting the equipment
The lawn mower is delivered partly assembled. The push bar and the grass basket must be assembled before using the lawn mower. Follow the instructions step by step and refer to the pictures when assembling.
Mounting the push bar (Fig. 3 to 7).
Insert the push bar holder (Fig. 2/Item 3) into the handlebar mount and secure with the quick clamping function (Fig. 2/Item 11) (Fig. 3). The top push bar (Fig. 1/Item 2) must be pushed onto the push bar holders (Fig. 2/Item 3) and secured as shown above in Fig. 4. Then attach the power cable to the push bar (Fig. 5/Item 13) using the cable clips (Fig. 2/Item 13). Now you can select the push bar height in three stages (Fig. 6/Item A).
Note!
The handle height may be adjusted only within the marked range.
- Press in the long handle and secure in the desired position using the quick clamping function (Fig. 6/Item 11)
Warning!
Always set the identical handle height on both sides.
Use the cable clips to align the cable to the long handle (Fig. 5/Item 13)
Fitting the grass box (see Figs. 7 to 9)
First plug the lower part of the housing (Fig. 2/ Item 15) and the right part of the housing (Fig. 2/
Item 18) together as shown in Fig. 7. Then plug the top part of the housing (Fig. 2/Item 17) onto the previously assembled parts (Fig. 8). Before you fit the grass basket you must ensure that the motor is switched off and the blade is not rotating. Lift the ejector fl ap (Fig. 9/Item 7) with one hand. With the other hand, hold the grass basket by the handle and hook it in from above (Fig. 9).
Filling level indicator of the grass collector
The grass box is equipped with a fi lling level indicator (Fig. 2/Item 16). which is opened by the airflow that the lawn mower generates during operation. If the fl ap closes during mowing, the grass collecting device is full and must be emptied. To ensure the proper functioning of the fi lling level indicator, the holes under the fl ap must always be kept clean and passable.
Adjusting the cutting height Caution!
Adjust the cutting height only when the machine has been switched off and the safety plug has been pulled out.
Before you begin to mow, check to ensure that the blade is not blunt and that none of the fasteners are damaged. To prevent any imbalance, replace blunt and/or damaged blades. To carry out this check, first switch off the motor and pull out the safety plug.
The cutting height is adjusted as follows (see Fig. 11):
- Push the lever (A) outwards.
- Set the lever (B) to the desired cutting height.
- Release the lever (A) and check that it is securely seated in the lock.
Reading off the cutting height
The cutting height can be set between 25 - 75mm in 6 intervals, and can be read off on the scale (Fig. 11/C).
Using the mulching adapter (Fig. 10)
In mulching mode the cuttings are shredded in the enclosed mower housing and then spread back onto the lawn. It is not necessary to gather and dispose of the grass.
Notice! Mulching is only possible if the lawn is relatively short.
GB
Warning!
Insert the mulching adapter only when the engine is switched off and the safety plug has been pulled out.
To use the mulching function, disconnect the debris bag, slide the mulching adaptor (Fig. 10/Item 23) into the ejector opening and close the ejector fl ap.
Charging the battery (Fig. 12a)
- Take the battery pack out of the equipment. Do this by pressing the side pushlock buttons.
- Check that your mains voltage is the same as that marked on the rating plate of the battery charger. Insert the power plug of the charger (19) into the socket outlet. The green LED will then begin to flash.
- Insert the battery pack (14) into the battery charger (19).
- In the section entitled „Charger indicator“ you will find a table with an explanation of the LED indicator on the charger.
The battery pack can become a little warm during the charging. This is normal.
If the battery pack fails to charge, check:
whether there is voltage at the socket outlet
whether there is good contact at the charging contacts
If the battery pack still fails to charge, send
the charging unit
and the battery pack
to our customer service center.
To ensure that items are properly packaged and delivered when you send them to us, please contact our customer service or the point of sale at which the equipment was purchased.
When shipping or disposing of batteries and cordless tools, always ensure that they are packed individually in plastic bags to prevent short circuits and fi res.
To ensure that the battery pack provides long service, you should take care to recharge it promptly. You must recharge the battery pack when you notice that the performance of the device drops. Never allow the battery pack to become fully discharged. This will cause it to develop a defect.
Installing the battery (Fig. 12b)
Open the battery cover. This is done by pulling the snap fastener (Item A) as shown in Fig. 12b and swinging up the cover. Then insert the two batteries in the mounts as shown in Fig. 12c.
Note!
Use only batteries which are charged to the same level. Never combine full and half-full batteries. Always charge the two batteries simultaneously. The equipment's operating time depends on the battery with the lower charge level. The two batteries must always be fully charged before use. Close the battery cover by swinging it down, and make sure that it latches in place correctly.
Battery capacity indicator (Fig. 13)
Press the button for the battery capacity indicator (Fig. 13/Item A). The battery capacity indicator (Fig. 13/Item B) shows the charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the battery from the equipment, keep it at room temperature for one day. If the fault reoccurs, this means that the rechargeable battery has undergone exhaustive discharge and is defective. Remove the battery from the equipment. Never use or charge a defective battery.
6. Operation
Caution!
The lawn mover is equipped with a safety circuit to prevent unauthorized use. Directly before starting up the lawn mover insert the safety plug (Fig. 12d) and remove the safety plug again whenever you interrupt or terminate your work.
Caution!
To prevent the equipment switching on accidentally, the lawn mower is equipped with a safety switch (Fig. 14/Item 8) which must be pressed
GB
before the switching bar (Fig. 14/Item 1) can be activated. The lawn mower switches itself off when the switching bar is released. The start time can amount to several seconds. The speed will drop after a few seconds when in idle mode and will rise again after a few seconds when in working mode. The lawn mower switches itself off when the switching bar is released. Repeat this process several times so that you are sure that the machine functions properly. Before you perform any repair or maintenance work on the equipment, ensure that the blade is not rotating and that the power supply is disconnected.
Caution! Never open the chute fl ap when the grass bag has been detached (to be emptied) and the motor is still running. A rotating blade can cause serious injuries!
Always carefully fasten the chute flap and grass basket. Switch off the engine before emptying the grass basket.
Always ensure that a safe distance (provided by the length of the long handles) is maintained between the user and the mower housing. Be especially careful when mowing and changing direction on slopes and inclines. Maintain a solid footing and wear sturdy, non-slip footwear and long trousers.
Always mow along the incline (not up and down). For safety reasons, the lawn mower may not be used to mow inclines whose gradient exceeds 15 degrees.
Use special caution when backing up and pulling the lawn mower. Tripping hazard!
Tips for proper mowing
It is recommended that you overlap the mowing swaths.
Only use a sharp blade that is in good condition. This will prevent the grass blades from fraying and the lawn from turning yellow.
Try to mow in straight lines for a nice, clean look. The swaths should overlap each other by a few centimeters in order to avoid stripes.
How frequently you should mow your lawn is determined primarily by the speed at which the grass grows. In the main growing season (May
- June) you will probably need to mow the lawn twice a week, otherwise just once a week. The cutting height should be between 4 - 6cm and the
amount of growth before mowing again should be 4 - 5cm. If the grass is allowed to grow somewhat longer for whatever reason, do not make the mistake of cutting it back to the normal height in one go. This will harm the lawn. Never cut it back by more than half the height in one go.
Keep the underside of the mower housing clean and remove grass build-up. Deposits not only make it more difficult to start the mower; they decrease the quality of the cut and make it harder for the equipment to bag the grass.
Always mow along inclines (not up and down). You can prevent the lawn mower from slipping down by holding a position at an angle upwards.
Select the cutting height according to the length of the grass. Make several passes so that no more than 4cm of grass are cut at one time. Switch off the motor before doing any checks on the blade. Keep in mind that the blade continues to rotate for a few seconds after the motor has been switched off. Never attempt to manually stop the blade. Regularly check to see if the blade is securely attached, is in good condition and is sharp. If the contrary is the case, sharpen the blade or replace it. In the event that the blade strikes an object, immediately switch off the lawn mower and wait for the blade to come to a complete stop. Then inspect the condition of the blade and the blade mount. Replace any parts that are damaged.
As soon as grass clippings start to trail the lawn mower, it is time to empty the grass basket. Important! Before taking off the grass basket, switch off the motor and wait until the blade has come to a stop.
To take off the grass basket, use one hand to lift up the chute fl ap and the other to grab onto the basket handle. Remove the basket. For safety reasons, the chute fl ap automatically falls down after removing the grass basket and closes off the rear chute opening. If any grass remains in the opening, it will be easier to restart the engine if you pull the mower back approximately 1m.
Do not use your hands or feet to remove clippings in or on the mower housing, but instead use suitable tools such as a brush or a hand broom.
In order to ensure that the majority of grass clippings are picked up, the inside of the grass basket must be cleaned after each use.
GB
Reattach the grass basket only when the motor is switched off and the blade has stopped.
Lift up the chute flap with one hand and, holding the grass basket by its handle with the other hand, hang in the basket from the top.
7. Cleaning, maintenance and ordering of spare parts
Danger!
Pull the safety plug before carrying out any cleaning work (Fig. 12d).
7.1 Cleaning
- Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.
- Do not clean the lawn mower with running water, particularly with high-pressure water.
We recommend that you clean the device immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device. - For best results, clean the lawn mower with a brush or rag.
7.2 Maintenance
Worn out or damaged blades, blade mounts, and bolts should be replaced as a set by an authorized professional in order to keep the equipment in balance.
- Ensure that all mounting components (i.e. screws, bolts, nuts etc.) are always tightened so that the equipment can be safely operated at all times.
- Frequently check the grass catch assembly for signs of wear.
- Replace excessively worn or damaged parts immediately.
In order to ensure that you enjoy the equipment for many years to come, all screwed parts, as well as the wheels and axles, should be cleaned and lubricated.
- Keeping your lawn mower in good condition not only ensures a long lifespan and high performance, but also enables the equipment to
thoroughly cut your grass with minimal effort.
- The blade is subjected to more wear and tear than any other component. Therefore, routinely check the condition of the blade and make sure that it is tightly fastened. If the blade is completely worn out, it must be immediately replaced or ground sharp again. An excessively vibrating mower means that the blade is not properly balanced or has become deformed from striking an object. In this case, the blade must be repaired or replaced.
There are no parts inside the equipment which require additional maintenance.
7.3 Replacing the blade
For safety reasons, we recommend having the blade replaced by an authorized professional. Important! Wear work gloves! Only replace the blade with a genuine Einhell replacement blade, as this will ensure top performance and safety under all conditions.
Carry out the following steps to change the blade: 1. Undo the fastening screw (see Fig. 15a).
2. Remove the blade and replace with a new one.
3. When fi tting the blade, make sure it is insta- talled in the right direction. The blade's air vanes must project into the motor compartment (see Fig. 15a). The dome mounts must be aligned with the punch holes in the blade (see Fig. 15b).
4. Then retighten the fastening screw with the universal wrench. The tightening torque should be approx. 25 Nm.
At the end of the season, perform a general inspection of the lawn mower and remove any grass and dirt which may have accumulated. At the start of each season, ensure that you check the condition of the blade. If repairs are necessary, please contact our customer service center. Use only genuine spare parts.
7.4 Ordering replacement parts:
Please quote the following data when ordering replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
- Replacement part number of the part required For our latest prices and information please go to www.einhell-service.com
Sparebladeart.no.:34.054.51
8. Storage and transport
Storage
Store the equipment and accessories out of children's reach in a dark and dry place at above freezing temperature. The ideal storage temperature is between 5 and 30^ . Store the machine in its original packaging.
Transport
- Switch the machine off and isolate it from the power supply before transporting it.
Fit the shipping protectors, if a - Protect the machine from damage and the strong vibrations that can occur particularly when transporting in vehicles.
- Secure the machine against slipping and tipping over.
9. Disposal and recycling
The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your local council offices.
GB
10. Charger indicator
| Indicator status Exp | anations and actions | |
| Red LED Green LED | ||
| Off | Flashing | Ready for useThe charger is connected to the mains and is ready for use; there is no battery pack in the charger |
| On Off Charging | The charger is charging the battery pack in quick charge mode. The charging times are shown directly on the charger.Important! The actual charging times may vary slightly from the stated charging times depending on the existing battery charge. | |
| Off | On | The battery is charged and ready for use.The unit then changes over to gentle charging mode until the battery is fully charged.To do this, leave the rechargeable battery on the charger for approx. 15 minutes longer.Action:Take the battery pack out of the charger. Disconnect the charger from the mains supply. |
| Flashing Off | Adapted charging | The charger is in gentle charging mode.For safety reasons the charging is performed less quickly and takes more time. The reasons can be:- The rechargeable battery has not been used for a very long time.- The battery temperature is outside the ideal range行动Wait for the charging to be completed; you can still continue to charge the battery pack. |
| Flashing Flashing Fault | Charging is no longer possible. The battery pack is defectiveACTION:Never charge a defective battery pack.Take the battery pack out of the charger. | |
| On On Temperature fault | The battery pack is too hot (e.g. due to direct sunshine) or too cold (below 0°C).Action:Remove the battery pack and keep it at room temperature (approx. 20°C) for one day . | |
11. Troubleshooting
| Fault | Possible causes Remedies | |
| The motor fails to start | a) The connectors have become se-parated from the motorb) The mower is standing in high grassc) The mower housing is cloggedd) Safety switch is not insertede) Battery is not correctly inserted | a) Have repaired by the Customer Service Centerb) Start in low grass or on an area that has already been mowed; change the cutting height if necessaryc) Clean the housing so that the blade moves freelyd) Insert safety switch (see 6.)e) Remove the battery and reinsert (see 5.) |
| The motor performance drops | a) The grass is too high or too dampb) The mower housing is cloggedc) The blade is severely wornd) Battery performance decrea-sing | a) Correct the cutting height, change the electronics settingb) Clean the housingc) Replace the bladed) Check the battery performance and charge the battery if necessary (see 5.) |
| Cutting is irregular | a) The blade is wornb) Wrong cutting height | a) Replace or resharpen the bladeb) Correct the cutting height |
Notice! For protection, the motor is equipped with a thermal switch which cuts out when the motor is overloaded and switches on again automatically after a short cooling period
GB
For EU countries only
Never place any electric power tools in your household refuse.
To comply with European Directive 2012/19/EC concerning old electric and electronic equipment and its implementation in national laws, old electric power tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.
Recycling alternative to the return request:
As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment. The old equipment can be returned to a suitable collection point that will dispose of the equipment in accordance with the national recycling and waste disposal regulations. This does not apply to any accessories or aids without electrical components supplied with the old equipment.
The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of the Einhell Germany AG.
Subject to technical changes
This consignment contains lithium-ion batteries.
In accordance with special provision 188 this consignment is not subject to the ADR regulations. Handle with care. Danger of ignition in case of damage to the consignment package. If the consignment package is damaged: Check and if necessary repackage.
For further information contact: 0049 9951 95920-66. Outside Germany charges will apply instead for a regular call to a landline number in Germany.
GB
Service information
We have competent service partners in all countries named on the guarantee certificate whose contact details can also be found on the guarantee certificate. These partners will help you with all service requests such as repairs, spare and wearing part orders or the purchase of consumables.
Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables.
| Category Example | |
| Wear parts* Carbon brushes, Battery | |
| Consumables* Blade | |
| Missing parts |
- Not necessarily included in the scope of delivery!
In the effect of defects or faults, please register the problem on the internet at www.Einhell-Service.com. Please ensure that you provide a precise description of the problem and answer the following questions in all cases:
Did the equipment work at all or was it defective from the beginning?
Did you notice anything (symptom or defect) prior to the failure?
What malfunction does the equipment have in your opinion (main symptom)?
Describe this malfunction.
GB
Warranty certificate
Dear Customer,
All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made:
- These guarantee terms apply to consumers only, i.e. natural persons intending to use this product neither for their commercial activities nor for any other self-employed activities. These warranty terms regulate additional warranty services, which the manufacturer mentioned below promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory guarantee claims are not affected by this guarantee. Our guarantee is free of charge to you.
- The warranty services cover only defects due to material or manufacturing faults on a product which you have bought from the manufacturer mentioned below and are limited to either the rectification of said defects on the product or the replacement of the product, whichever we prefer. Please note that our devices are not designed for use in commercial, trade or professional applications. A guarantee contract will not be created if the device has been used by commercial, trade or industrial business or has been exposed to similar stresses during the guarantee period.
-
The following are not covered by our guarantee:
-
Damage to the device caused by a failure to follow the assembly instructions or due to incorrect installation, a failure to follow the operating instructions (for example connecting it to an incorrect mains voltage or current type) or a failure to follow the maintenance and safety instructions or by exposing the device to abnormal environmental conditions or by lack of care and maintenance.
- Damage to the device caused by abuse or incorrect use (for example overloading the device or the use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand, stones or dust, transport damage), the use of force or damage caused by external forces (for example by dropping it).
-
Damage to the device or parts of the device caused by normal or natural wear or tear or by normal use of the device.
-
The guarantee is valid for a period of 24 months starting from the purchase date of the device. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fitted. This also applies if an on-site service is used.
-
To make a claim under the guarantee, please register the defective device at: www.Einhell-Service.com. Please keep your bill of purchase or other proof of purchase for the new device. Devices that are returned without proof of purchase or without a rating plate shall not be covered by the guarantee, because appropriate identification will not be possible. If the defect is covered by our guarantee, then the item in question will either be repaired immediately and returned to you or we will send you a new replacement.
Of course, we are also happy offer a chargeable repair service for any defects which are not covered by the scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send the device to our service address.
Also refer to the restrictions of this warranty concerning wear parts, consumables and missing parts as set out in the service information in these operating instructions.
F
Danger!
Chere cliente, cher client,
- nabijecku
aakumulatorovyclanek
Tipode protection: IPX1
Svetita 2 ali 1 lucka LED:
Stimata clienta, stimate client,
produsele noastre sunt supuse unui control de calitate riguros. Daca totusi vredata acest aparat nu va fonctiona ireprosabil, ne pare foarte rau si va rugam sa va adresa t centrului nostru service, la adresa indica la finalul acestui certificat de garantie. Bineinteles ca va stam si la Telefon cu placere la disposizite, la numeroile de service mentionate. Pentru revendicarea pretentiilor de garantie trebuie tinut cont de urmatoarele:
Evnpwon yia to epbic
Rotacoes do motor: 3000 r.p.m.
5. Pre puštanja u pigeon
Kosilica za travu je prilikom isporuke montirana u delovima. Pre upotrebe kosilice za travu morate da montirate completingu drsku za guranje i korpu za travu. Postujte uputstva za upotrebu korak po korak i orijentirajte se prema slikama za vreme sastavljanja.
Montažarucezaguranje(slika3do7)
Drzač ručke za guranje (slika 2 / poz. 3) stavlja se u prihvat drške i pričvršćuje pomocu funkcjije brzog pritezanja (slika 2 / poz. 11) (slika 3). Gornja ručka za guranje (slika 1 / poz. 2) mora da se gurne na držac ručke za guranje (slika 2 / poz. 3) i da se pričvrsti kao što je prikazano na slici 4. Zatim pomocu držac kabla (slika 2 / poz. 13) pričvrstite kabl motora na ručku za guranje (slika 5 / poz.
13). Sada mozte da izabere te visin drske u 3 stepena (sika 6 / pz. A).
Napomena!
区2000/14/EC_2005/88/EC
Annex V
Annex VI
Noise: measured Lw = 88.1 dB (A); guaranteed Lv / s = 90 dB (A)
P = kw; L/D = 43 cm
Notified Body: TUV SUD Industrie Service GmbH (NB 0036)
2012/46/EU_(EU)2016/1628
Emission No.
Standard references: EN 60335-1; EN 60335-2-77; EN 62233; EN 55014-1; EN 55014-2
Subject to change without notice
a GB Officn low nore . Pndone a gzen a accumulation . Tbsae a bettare . DNX Nk Aegsmaasak . S Bafderlntiig kredikp . CZ Akumulotora sokaai . SK Akumulotora oasaika. NL Accugemzamara . E Cortosapata a batera . Fw AKukidyfohim tononuiai . SLO Akumolatra koslinae zr hve . H Akuynthogop . RO Maghdin tch guns ruru c u acumulatran . GR Xkoovzarno p icmuptar . Pco-reves sem fo . HRSHA Aucunutura koslita za Irua . AS Akumulotara koslita za Irua . PL Akumulotara oasaika do crayy Trak Altiqim biye . RAC Kauvzarno 1000000000000000000000000000000000000000000000000000000000000000000000000000000
Declaration of conformity
We, Einhell UK Ltd
Champions Business Park, First Floor Unit 10, Arrowe Brook Rd, Upton, Wirral CH49 0AB, United Kingdom
declare the conformity to UK standards and legislation was assessed for:
Cordless Lawn Mower GE-CM 43 Li M (Einhell)
UK legislation
Simple Pressure Vessels (Safety) Regulation
Electrical Equipment (Safety) Regulation
Radio Equipment Regulation
Personal Protective Equipment Regulation
The Ecodesign for Energy-Related Products and Energy Information Regulation
X The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulation
X Nolse Emisslon in the Environment by Equipment for use Outdoors Regulation
Noise:measuredL W = 88,1 dB (A); guaranteed L W = 90 dB (A)
Supply of Machinery (Safety) Regulation
Annex IV
UK Approved Body:
UKTE Certificate No.:
Standards: BS 60335-1; BS 60335-2-77; BS 62233; BS 55014-1; BS 55014-2
Wirral, 2021.09.08
Archive-File/Record: NAPRO26349
Article Number: 34.131.30 I-No.:21041
Subject to change without notice Wiesenweg 22, 94405 Landau/Isar, Germany
Documents registrar: Thomas Fischer
D Konformitätserklarung: Wir erklärten Konformität gemäß EU-Richtlinie und Normen für Anteil
GB Declaration of conformity: We declare conformity in accordance with the EU directive and standards for article
F Déclaration de conformité: Nous déclarons la conformité conformément aux directives et normes UE pour l'article
I Dichiarazione di conformità: dichiariamo la conformità seconda la direttiva UE e le norme per l'articolo
DK Overensstammelsoserklae:Vi attestor overensstammelso itt. EU-direktivamt standarder for arterlk
S Forakran over ovensamstelle. Vi Forkilar foljende ovensamstelle, el Liudiklu och standarder for adinkel
CZ Prohásiński o shod: Prohásijsnejeme shodu podle smarne EU a norem pro vyrobek
SK Vyhlasenie o zholde: Vyhlasujeme zhodu podla smernice EU a noriem pre vyrobst
NL Conformitaisverklaring: wirVkwranken conformiteit conform EURichtlin en normen voor arterik
E Declaración de conformidad: clararamos la conformidad a tenor de la directiva y normas de la UE para el articulo
FIN Standardirmukaisustodistus: Me vakuutama, alla EU-direktiin ja standarden vaatimukset tavyttvat touelloe.
SLO IJAZAVA OKSLADNOSTI potjue sleedeco skladnost s smernico EU in standardzia izdelek
H Konformitäsi nyilakozat: Az EU-irányvoc énsmák szerinti konformitäst jolentjú kì cíkákezhé
RO Declaratie de conformitate: Declarant conformitate conform directiveisnormeloreUEpentruarticolul
GR dAuao ouapoeoocn; dAaioueouaouapoeo oOpaovae uO ovEa Ea kai noTtura vao tnoNtO
P Declariace de conformidade: Declaramos a conformidade de accordo com a direlva CE e nomras para o arterio
HR IJAZVA O SUKLADNOSTI potvrduje sljeDECU uskladenost prema smiernicama EU n omarna za artikl
BIJ UJAVA O SUKLADNOSTI potvrduje sijdececu uskladnost prema smiernicama EU i normamaca artiki
RDS DEKLARACJIA O USUGLASENSON POT virdule sleedecu uskladenost propem osmericama EZ i nomara z a artikal
TR Uygunluk Deklarasyonyu: AB direktfi ve ürün standartlan uyanca uygunluyuoyan bevan ederiz
BUS. 3a8b0HmO COOTBETCTHM TOpA: HactoHUM
YJDCTOSEBPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTCPOCTC
EE Vastavusdeklaratosoon: Toendame toote vastavust EL direktivile ja standardtiele
LV Atbilistbas doklarija: Mesi aplicinam atbilistbu ESI direktivuan standiarmtai tajik minetajam pecem
LT Altiklides deklaracija:deklaruojame, kad gaminis altinka ES direkviya er standatius
PL Doklaraca Zgodnosci - deklarujemny zgodnosoc wymienionego porizej artykulz nastepujacyn normami na podstawe dyrektyw EU
BGEHJAPAAH3A CHOTBETTHEH HME HJAKHPAMAE CHOTBETCTHEH AHNDPKHTHTHEN HOPMHTE (EC) 3A HEDAN
UKR DeNaparaji BniDIOHOTi MNNBREMO PNO BINIHOHCTI aIaio H NpEeTbKOEOC EC TA cTAeADPTAM CTOBOOHOAHTVHO
MK 13jaa 3a coo6pa3HOCT;H3jauybaMoo6p3aHOCT CO peryhaTnBa HcnpMTHe AEv aptTKHn
N Samsvarskarading: Vi eklarer samsvar i hendifoll EU-direktiv og standarder for artickel
IS Samamrisyifirising:ViD utskurdum samraemi vii EU-regluger og stolum fyr vortugedun
区2000/14/EC_2005/88/EC
Annex V
Annex VI
Noise: measured LvA = 88.1 dB (A); guaranteed LvA = 90 dB (A)
P = kW; L/0 = 43 cm
Notified Body: TUV SUD Industrie Service GmbH (NB 0036)
2012/46/EU_(EU)2016/1628
Emission No.
Standard references: EN 60335-1; EN 60335-2-77; EN 62233; EN 55014-1; EN 55014-2
Subject to change without notice
a GB Officn low nore . Pndone a gzen a accumulation . Tbsae a bettare . DNX Nk Aegsmaasak . S Bafderlntiig kredikp . CZ Akumulotora sokaai . SK Akumulotora oasaika. NL Accugemzamara . E Cortosapata a batera . Fw AKukidyfohim tononuiai . SLO Akumolatra koslinae zr hve . H Akuynthogop . RO Maghdin tch guns ruru c u acumulatran . GR Xekovarto m pntmuptro . P Conreves sem fo . HRSHA Aucumalotra koslita za Iruu . AS Akumulotra koslita za Iruu . PL Akumulotra kosilica za Iruu . TR Akutri pmtgne . RAC Kauvayrno 1000000000000000000000000000000000000000000000000000000000000000000000000000000
Declaration of conformity
We, Einhell UK Ltd
Champions Business Park, First Floor Unit 10, Arrowe Brook Rd, Upton, Wirral CH49 0AB, United Kingdom
declare the conformity to UK standards and legislation was assessed for:
Cordless Lawn Mower GE-CM 43 Li M (Einhell)
UK legislation
Simple Pressure Vessels (Safety) Regulation
Electrical Equipment (Safety) Regulation
Radio Equipment Regulation
Personal Protective Equipment Regulation
The Ecodesign for Energy-Related Products and Energy Information Regulation
The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulation
X Nolse Emisslon in the Environment by Equipment for use Outdoors Regulation
Noise:measuredL = 88,1 dB(A);guaranteed L_W = 90 dB(A)
Supply of Machinery (Safety) Regulation
Annex IV
UK Approved Body:
UKTE Certificate No.:
Standards: BS 60335-1; BS 60335-2-77; BS 62233; BS 55014-1; BS 55014-2
Wirral, 2021.09.08
Archive-File/Record: NAPR026554
Article Number:34.131.30 I-No.:21061
Subject to change without notice Wiesenweg 22, 94405 Landau/Isar, Germany
Documents registrar: Thomas Fischer
EH 10/2021 (02)
