LaserJet Ultra MFP M133 - Printer HP - Free user manual and instructions

USER MANUAL LaserJet Ultra MFP M133 HP

• Dansk p. 19
• Català p. 16
• Español p. 13
• Italiano p. 10
• Deutsch p. 7
• Français p. 4
• English p. 1
• Norsk p. 37
• Lietuvių p. 34
• Latviešu p. 31
• Suomi p. 28
• Eesti p. 25
• Nederlands p. 22
• Svenska p. 43
• Português Windows1. For Windows 7 or lower, do not connect the USB cable before installing the software. The installation process prompts to connect the cable at the appropriate time. If the cable is already connected, restart the printer when installation prompts to connect the cable. p. 40

2. Continue to “6. Locate or download the software installation les.”

NOTE: During Windows software installation, select the option to connect through a network. Mac

1. For Mac, connect the USB cable between the computer and the printer before installing the software.

2. Continue to “6. Locate or download the software installation les.”

Wireless network connection (wireless models only)Touchscreen control panels1. To connect the printer to a wireless (Wi-Fi) network, on the printer control panel, touch the Wireless button.

2. Touch Wireless Menu, and then touch Wireless Setup Wizard. Select the

network name from the SSID list, or enter the network name if it is not listed.

3. Use the keyboard to enter the passphrase, and then touch the OK button.

4. Wait while the printer establishes a network connection.5. On the printer control panel, touch the Network button. If an IP address is listed, the network connection has been established. If not, wait a few more minutes and try again. Note the IP address for use during software installation. Example IP address: 192.168.0.1

6. To print from a computer, continue with “6. Locate or download the

software installation les.” To print from a phone or tablet only, continue with “8. Mobile and wireless printing (optional).”2-line control panels1. To connect the printer to a wireless (Wi-Fi) network, make sure that the printer, access point, and computer are turned on and that the computer is connected to the wireless network.2. A USB cable will be required.3. Disconnect any USB or Ethernet cable that is connected to the printer.

4. To print from a computer, continue with “6. Locate or download the

software installation les.” To print from a phone or tablet only, continue with “8. Mobile and wireless printing (optional).” NOTE: During software installation, select the option to Help me set up a rst-time wireless connection. Wired (Ethernet) network connection (optional)Use a standard network cable.1. Connect the network cable to the printer and to the network. Wait a few minutes for the printer to acquire a network address.

2. Continue to “6. Locate or download the software installation les.”

NOTE: During software installation, select the option to Connect through a network.www.hp.com/support/ljM129MFP www.register.hp.com USB connection directly between the printer and the computerUse an A-to-B type USB cable. IMPORTANT: Follow Steps 1 - 3 on the printer hardware setup poster, then continue with Step 4.

Select a connection method

Set up the control panel At the printer control panel, check the display status before beginning software installation. Manually congure the IP addressSee the printer user guide for information on how to manually congure the IP address www.hp.com/support/ljM129MFP. LaserJet Pro MFP M129-M132, LaserJet Ultra MFP M133-M134 Getting Started Guide2 Windows solution

1. Insert the printer CD into the computer, or launch the software

installation le downloaded from the web.

2. The software installer detects the language of the operating system, and

then it displays the main menu of the installation program in the same language. When installing from the CD, if the installer program does not start after 30 seconds, browse the CD drive on the computer, and then launch the le named SETUP.EXE.

3. Follow the on-screen instructions to install the software.

4. When prompted to select a connection type, select the appropriate option

for the type of connection:

• Directly connect this computer using a USB cable

• Connect through a network

• Help me set up a rst-time wireless connection NOTE: When connecting through a network, the easiest way to detect the printer is to select Automatically nd my product on the network. OS X solution Mac users can click the link on the CD, or go directly to 123.hp.com and download HP Easy Start to install the printer software.

1. Go to 123.hp.com.

2. Enter HP LaserJet Printers.

3. Click Begin, and then click Download to download HP Easy Start.

4. Open HP Easy Start, and then follow the on-screen instructions.

Readiris Pro for HP Download this free software to enable extra scanning features, including Optical Character Recognition (OCR). To download the software from the web, go to: www.hp.com/support/ljM129MFP Select Drivers, select the appropriate operating system, and then click Next. Click Application - 3rd Party, and then click the Download button.

Install the software Method 1: Download HP Easy Start (Windows and OS X)

1. Go to 123.hp.com/laserjet, and click Download.

2. Follow the on-screen instructions and prompts to save the le to the computer.

3. Launch the software le from the folder where the le was saved, and continue

with “7. Install the software.” Method 2: Download from the printer support website (Windows and OS X)

1. Go to www.hp.com/support/ljM129MFP.

2. Select Software and drivers.

3. Download the software for your printer model and operating system.

4. Launch the software le from the folder where the le was saved, and continue

with “7. Install the software.” Method 3: Install from the printer CD (Windows only)

1. Insert the printer CD into the computer.

2. Continue with “7. Install the software.”3

To use HP ePrint via email, the printer must meet these requirements:

• The printer must be connected to a wired or wireless network and have Internet access.

• HP Web Services must be enabled on the printer, and the printer must be registered with HP Connected. Enable HP Web Services 2-line LCD control panel

1. Once the printer is connected to a network, enter the printer’s network

IP address into a web browser. Use one of the following options to nd the printer IP:

• Go to “Find printer IP address,” in this getting started guide

• Refer to the user guide

2. On the web page that appears, click the HP Web Services tab.

3. Review and accept the terms of use, and then click the Enable button.

Touchscreen control panel

1. From the Home screen on the printer control panel, touch the Web Services

then prints an information page. The information page contains a printer code necessary to register the HP printer at HP Connected.

3. Go to www.hpconnected.com to create an HP ePrint account and complete the

setup process. Use HP ePrint via email to print documents by sending them as an email attachment to the printer’s email address from any email enabled device, even from devices that are not on the same network.

Connect the device to the wireless network To print from a phone or tablet, connect the device to the same wireless network as the printer. Apple iOS devices (AirPrint) Open the item to print, and select the Action icon. Select Print, select the printer, and then select Print. Newer Android devices (4.4 or newer) Open the item to print, and select the Menu button. Select Print, select the printer, and select Print. Some devices require downloading the HP Print Service plugin app from the Google Play store. Older Android Devices (4.3 or older) Download the HP ePrint app from the Google Play store. Windows Phone Download the HP AiO Remote app from the Windows Store. Learn more about mobile printing To learn more about other mobile printing options, including additional ePrint solutions, scan the QR code, or see the “Mobile printing” section of the user guide.

Wi-Fi Direct (wireless models only) Wi-Fi Direct enables close-proximity printing from a wireless mobile device directly to an Wi-Fi Direct-enabled printer without requiring a connection to a network or the Internet. Enable Wi-Fi Direct To enable Wi-Fi Direct from the control panel, complete the following steps.

2. Open the following menus:

• Settings (touchscreen control panels only)

printing . For more information on wireless printing and wireless setup, go to www.hp.com/go/wirelessprinting. Discover the printer

1. From the mobile device, turn on the Wi-Fi, and search for wireless

2. Select the printer, which will show up as ‘HP-Print-model-name’ as

Mobile and wireless printing (optional)

Set up HP ePrint via email (optional) Use the HP Scan software on your computer to start a scan job at the printer. Windows Open HP Printer Assistant, select Scan, and then select Scan a Document or Photo. OS X Click Applications, select HP, and then select HP Easy Scan.

2. The software installer detects the language of the operating system,

2. Voer HP LaserJet Printers in.

2. Sisestage HP LaserJet Printers.

2. Digite HP LaserJet Printers.

1. Acesse www.hp.com/support/ljM129MFP.

Använda skanningfunktionen4647© Copyright 2016 HP Development Company, L.P. Reproduction, adaptation or translation without prior written permission is prohibited, except as allowed under the copyright laws. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Trademark Credits Windows® is a U.S. registered trademark of Microsoft Corporation. Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. OS X is a trademark of Apple Inc., registered in the U.S. and other countries. AirPrint is a trademark of Apple Inc., registered in the U.S. and other countries. FCC Regulations This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio-frequency energy. If this equipment is not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase separation between equipment and receiver.

• Connect equipment to an outlet on a circuit dierent from that to which the receiver is located.