EWB 3281 - Ice machine CLATRONIC - Free user manual and instructions

USER MANUAL EWB 3281 CLATRONIC

Silver industrial bread maker with no visible text or symbols on the device body

CE

DEUTSCH

УКРАЇНСЬКА

Inhalt

Volume watertank: ca. 2 liter

Koelvloeistof: R134a/ 85 gram

General Safety Guidelines

Before using this device, carefully read this user manual and keep it together with the Warranty Certificate, cashier receipt and if possible, the original package inclusive its interior packing. If you hand on the device to any third person, include the user manual as well.

• Use the device for private and its intended purpose only. The device is not intended for commercial use.
  Do not use the device outdoors. Protect it from heat, direct sunlight, humidity (do not immerse into liquids under any circumstances) and sharp edges. Do not use the device with wet hands. If the device gets wet, unplug it immediately.
• Always switch off and unplug the device (pull the plug, not the cable) when you do not use the device, or when you attach accessories, during cleaning or malfunctioning.
• Do not leave the device unattended during operation. Always switch off the device when leaving the room. Unplug the device.
• Regularly check the device and cable for signs of damage. Do not continue to operate the device in case of damage.
• Do not repair the device by yourself. Please contact authorized personnel. In order to avoid hazards, a damaged mains cable must be replaced with an equivalent cable by the manufacturer, our customer service or any other qualified specialist.
• Do only use original parts.
• Please observe the following "Special safety instructions".

Children and disabled persons

- For the safety of your children, keep any packing parts (plastic bags, cartilage, Styrofoam etc.) out of their reach.

Warning!

Don't let small children play with foils for danger of suffocation!

• This device is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and/or knowledge unless they have been given supervision or instructions concerning the use of the device by a person responsible for their safety.
• Supervise children to ensure they do not play with the device.

Symbols in this user manual

Important notes for your safety are marked distinctively. Pay absolute attention to them to avoid accidents and damage to the device.

Warning:

Warns of dangers for your health and indicates potential risks of injury.

Attention:

Indicates potential dangers for the device or other objects.

Note:

Highlights tips and information for you.

Special Safety Precautions

Attention:

• Please observe a waiting period of 2 hours before initial operation and after moving the appliance for the coolant to settle; otherwise the compressor can be damaged.

• Only use potable water.

• Move and store the appliance only upright.

• Do not place the appliance on or in close proximity of heat sources, such as ovens, heaters, etc.
• Place the appliance on a stable, level surface. Keep a distance of at least 15 cm on all sides.
• Ensure not to obstruct the ventilation slots.

Location of Controls

1 Indicator lamp READY
2 Indicator lamps S, M, L
3 Indicator lamp WATER REFILL
4 STOP button
5 SELECT button (cube size)
6 START button
7 Residual water drain valve
8 Lid (ice cube compartment/water tank)
9 Viewing window
10 Ice cube container
11 Temperature sensor (ice fill level)
12 Ice scoop

Intended Use

This appliance makes ice cubes from potable water.

The appliance is only intended for this use. Use this appliance only as described in this user manual. Do not use this appliance commercially.

All other use is not intended and can cause damages to the appliance and even injuries.

Clatronic International GmbH does not accept liability for damages caused by unintended use.

Unpacking the device

- Unpack the device.

- Remove all packaging materials such as foils, filling material, cable ties and cardboard packaging.

i Note:

The appliance may still be covered in some residues from the manufacturing process. Please clean the appliance as described in chapter "Cleaning and Maintenance".

Operation

△ Attention:

Please observe a waiting period of 2 hours before initial operation and after moving the appliance for the coolant to settle; otherwise the compressor can be damaged.

Mains Power Connection

• Be sure the voltage of the appliance (rating plate) corresponds with the mains voltage before connecting to mains power supply.
• Connect the appliance to a properly installed 230V\~50Hz wall outlet.

Making Ice Cubes

i Note:

For hygienic reasons do not use the ice cubes from the first cycle.

1. Open the lid and remove the ice cube container.
2. Fill the water tank with potable water (tap water) to the MAX marking.

△ Attention:

Only use potable water without additives!

i Note:

• The MAX marking is inside the water tank, around the lower edge of the ice cube container.
• The water level must be below the ice cube container.

• Only use water at room temperature.

• Replace the ice cube container and close the lid.

• Press SELECT to select the desired ice cube size; the corresponding indicator lamp lights up.

$$ S = \text { small }, M = \text { medium }, L = \text { large } $$

1. Press START to start the ice cube production. The process takes between 9 and 13 minutes.

2. Keep the lid closed.

i Note:

• The production time depends on the set ice cube size.
• Depending on water/ambient temperature the first ice cubes come out a bit smaller. During the next cycles the ice cubes get to the set size.
• The ice cube size depends on the ambient temperature:
• At 15°C ambient temperature we recommend setting "S"; otherwise the ice cubes may stick together, which can lead to problems with the automatic scoop.
• At 30°C ambient temperature we recommend setting "L".
• Due to fast freezing the ice cubes can look "milky". This is the air trapped in the water and does not influence the quality of the ice cubes.

Stop Ice Cube Production

Press STOP to stop ice cube production.

i Note:

Before finally stopping the appliance automatically empties the water tank and dissolves already produced ice cubes.

Indicator Lamp READY

The temperature sensor stops the ice cube production as soon as the ice cube container is full. The indicator lamp READY lights up and a beep tone sounds.

• Remove the ice cubes with the supplied ice cube scoop.
• The indicator lamp READY turns off and a few moments later ice cube production starts again.

Indicator Lamp WATER REFILL

The indicator lamp turns on if the water tank is nearly empty and a beep tone sounds. Ice cube production is automatically halted.

- Refill with potable water as described in chapter "Making Ice Cubes".

Attention:

Wait at least 3 minutes before turning the appliance on again, otherwise the compressor can be damaged.

- Press START to resume making ice cubes; the indicator lamp WATER REFILL turns off.

Cleaning and Maintenance

Warning:

Always disconnect from mains power supply before cleaning.

Attention:

• Do not use harsh or abrasive cleaning agents.
• Do not use chemicals, acids, petrol or oil products.
• Do not submerge the appliance in water.

Note:

• For hygienic reasons exchange the water in the tank after 24 hours.
• To avoid fungi and bacteria leave the lid open after use.

Ice Cube Container (10)

Remove the ice cube container and clean it with a mild detergent under running warm water.

Casing and Interior

• Clean casing and interior with a damp cloth.
• Use a diluted solution of vinegar and water.

Drain Residual Water (7)

Drain the residual water if the appliance is not in use for a longer period of time.

• To drain the residual water open the residual water drain valve clockwise.
• Close the residual water drain valve after the residual water has been drained.

Troubeshooting

Problem Possible Cause Solution
No function. No power supply. Check the wall outlet with a different appliance; connect the plug properly to the wall outlet.
Compressor noisy. Mains power supply too low. Turn the appliance off and check the mains power supply.
Indicator lamp WATER REFILL flashes.	Water level too low. Refill water “Making IceCubes”.
Indicator lamps do not turn on. No power supply.		Connect to mains power supply.
		Check fuse.
		Applicance defective.
Ice cubes are too large and stick together.	Water temperature or ambient temperature too low.	Stop ice cube production.Select setting “S” and restart the appliance.
Indicator lamps READY and WATER REFILL light up at the same time.	Water tank is blocked by ice cubes.	Disconnect from mains power supply. Remove the ice cubes from the automatic scoop.Reconnect and press START.

Noise emission

The workplace-related emission value is less than 70 dB(A).

Technical Specifications

Model: EWB 3281

Voltage supply: 220-240V\~50Hz

Power input: 150 W

Ice cube production: 12-15 kg / 24 hrs

Water tank volume: .... approx. 2 Liters

Coolant: R134a/85g

Protection class: ....I

Net weight: 12 kg

Subject to change without prior notice!

This device complies with all current CE directives, such as electromagnetic compatibility and low voltage directive and is manufactured according to the latest safety regulations.

Meaning of the "Wheelie Bin" Symbol

Take care of our environment, do not dispose of electrical appliances via the household waste.

Dispose of obsolete or defective electrical appliances via municipal collection points.

Please help to avoid potential environmental and health impacts through improper waste disposal.

You contribute to recycling and other forms of utilization of old electric and electronic appliances.

Your municipality provides you with information about collecting points.