Q: Where to buy the laser or spare parts for the DEXTER DX254?

The integrated laser of the DEXTER DX254 (class 2, 650 nm, ADEO authorized service (manufacturer): Contact ADEO service directly at: 135 rue Sadi Carnot, CS 00001, 59790 RONCHIN, FRANCE You can also contact your Leroy Merlin store, which can initiate the request with ADEO service For repairs or replacements of the laser, only the manufacturer or an authorized representative is allowed to intervene (to ensure compliance with safety standards) Spare parts and accessories: The common wear parts available are: motor brushes, 254 mm saw blade, table insert, and dust collector bag Contact ADEO service to obtain the exact references of the parts you need Ask specialized tool distributors for miter saws (check compatibility with the DX254 model before purchasing) Important: Your saw comes with a manufacturer's warranty of 24 months for normal domestic use. If the laser no longer works or if you notice a failure and the product is still under warranty, first contact ADEO service or your Leroy Merlin dealer before purchasing a spare part. Repair costs may apply outside the warranty period.

Q: How to locate and use the laser on the DEXTER DX254 miter saw?

Location of the laser: The laser of your DEXTER DX254 miter saw is located on the machine head. It is controlled by the laser On/Off switch n°33 , which is easily accessible on the machine's housing. Activation and use: Press the switch n°33 once to activate the laser. A red laser beam will appear on the workpiece, indicating the cutting line in real-time. Press the same switch again to turn off the laser. Adjusting the laser: If the laser beam no longer aligns correctly with the cutting line, you can adjust it. Loosen the crosshead screws (D) located near the laser module. Push the laser sideways until the laser beam precisely reaches the teeth of the saw blade (6). Once the alignment is correct, tighten the two crosshead screws firmly. Laser maintenance: The laser operates on batteries. If you do not use the saw for an extended period, it is advisable to remove the batteries to prevent them from draining. If the beam weakens, simply replace the batteries. Technical specifications: The laser complies with class 2 (wavelength: 650 nm, power less than 1 mW). It meets current safety standards and can only be repaired or replaced by the manufacturer or an authorized representative. Essential safety instructions: Never look directly into the laser beam, even briefly. Never direct the beam at reflective surfaces, people, or animals, as even a low-power laser can cause eye damage. Never open the laser module yourself. Always protect your eyes when using the laser.

Q: Can I use smaller cutting discs on the DEXTER DP6 grinder?

Yes, but with important conditions. The DEXTER DP6 model (2100AG2-230.5001) is designed for cutting discs with a diameter of 230 mm , but the technical manual indicates an accepted alternative: you can use 125 mm discs (maximum thickness 6 mm) on this device. Essential conditions: Compatible bore: The central hole must be 22.2 mm (M14) - this is the standard for this grinder Thickness: For 125 mm discs, the maximum allowed thickness is 6 mm Rotation speed: This grinder operates at a maximum of 6,500 RPM . You must ensure that the smaller disc does not exceed this limit (smaller discs often have a higher maximum speed) Type of disc: For cutting discs, only diamond and reinforced bonded versions are accepted according to the manual With a power of 2100W, your device has the necessary power for 125 mm discs without any issues.

Q: How to install the protective guard on the Dexter 800AG2-125.5001 angle grinder?

To correctly install the protective guard on your Dexter 800AG2-125.5001 angle grinder, follow the steps below: Steps to install the protective guard: Ensure that the grinder is turned off and unplugged from any power source to ensure your safety. Release the locking lever of the guard by pulling it outward. Position the guard on the grinder's spindle by rotating or adjusting it to the desired angle. Close the locking lever by pushing it to secure the guard in place. Check that the raised edge of the guard is properly inserted into the notch on the bearing cap. Important information: The closed side of the guard should always face the operator for optimal protection. The guard can be adjusted up to 45° to the left or right according to your needs. To reposition the guard, unlock the lever, adjust the angle, and then lock it again. Never use the grinder without the protective guard properly installed and locked.

Q: How to properly connect the suction hose to the DEXTER 710DWS2-225.1001 drywall sander?

To connect the suction hose to your DEXTER 710DWS2-225.1001 drywall sander, follow these precise steps: Always unplug the sander before proceeding with the assembly to ensure your safety. Loosen the sleeve of the dust extraction port (located on the upper extension shaft). Important: do not completely remove the sleeve, just loosen it. Before attaching the sanding paper, precisely align the holes of the sanding paper with those of the base plate . This step is essential to ensure effective dust extraction and avoid air leaks. Gently press the sanding paper to attach it to the base plate. Insert the suction hose connector into the dust extraction port until it reaches the stop . Make sure it is securely engaged. Secure the connection by tightening the sleeve on the port. This step prevents any accidental disconnection of the hose during operation. Then attach the other end of the hose to a suitable vacuum cleaner using the provided vacuum adapter. To remove the hose, simply loosen the sleeve, hold the handles, and pull the connector out of the port. Important tip: The device can only be connected to one maximum extension tube . Aligning the holes of the sanding paper is crucial as it directly optimizes the suction flow and significantly reduces airborne dust.

Q: How to solve the problem of the laser not turning on the DEXTER DX216 miter saw?

If the laser of your DEXTER DX216 miter saw does not turn on, the problem usually comes from the batteries that power the laser module. Here’s how to resolve it: 1. Replace the laser batteries The laser of the DEXTER DX216 operates on batteries. This is the most common cause of malfunction. Locate the battery compartment of the laser module (item 32) at the front of the saw and open it. Replace the batteries with new ones of the same type (usually AA or AAA batteries depending on the model). Ensure that the batteries are installed correctly, respecting the + and - polarities. 2. Check the laser On/Off switch Press the laser On/Off switch (item 33) firmly once. A laser beam should then be projected onto the material to be cut. If nothing happens after replacing the batteries, the switch may be defective. 3. Clean the laser lens A buildup of dust or sawdust on the laser lens can prevent the beam from displaying correctly. Gently clean the lens with a dry, clean cloth. Avoid using abrasive products that could scratch the optical lens. 4. Check the overall power supply of the saw Make sure that the miter saw is properly plugged in and that the main switch of the machine is in the ON position. An unpowered saw will not have a functional laser, even if the device starts. 5. Contact customer service if the issue persists If after replacing the batteries and cleaning the laser remains non-functional, this may indicate a defect in the laser module. Laser repairs can only be performed by the manufacturer or an authorized representative. Contact ADEO customer service at: 135 RUE SADI CARNOT CS00001, 59790 RONCHIN, FRANCE. The product is guaranteed for 24 months against manufacturing defects.

Q: What should I do if my DEXTER 300DS2.5 sander does not turn on?

If your DEXTER 300DS2.5 sander does not turn on, several checks can help you identify and resolve the issue: 1. Check the power supply Make sure the sander is properly plugged into a functional electrical outlet. Test the outlet with another device to confirm it is delivering power. 2. Check the power cord Inspect the cord for cuts, exposed wires, or signs of wear. A damaged cord may prevent the sander from turning on and should be repaired or replaced. 3. Check the switch Ensure that the switch is in the

Q: Do the DEXTER cordless drills 12SD2-25RC.1A, 20SD2-35RC.2A, and 20SD2-35RC.2B have a hammer mode?

The DEXTER cordless drills models 12SD2-25RC.1A, 20SD2-35RC.2A, and 20SD2-35RC.2B are generally not equipped with a hammer mode. These models are primarily designed for drilling and screwing in standard materials such as wood, plastic, or metal, but do not have the hammer function that is useful for drilling into harder materials like brick or concrete. The hammer mode allows the drill to make quick, small blows in addition to rotation, thus facilitating drilling into hard materials. The absence of this function means that these models are better suited for light to medium tasks and are not suitable for work requiring hammer drilling. If you need a drill with a hammer mode, it is advisable to look for a model specifically designed for that, often referred to as a "hammer drill" or "combination drill."

Q: How to properly use the DEXTER LM70235921 soldering lamp?

To properly use the DEXTER LM70235921 soldering lamp, follow these essential steps to ensure safe and effective use: 1. Preparing the workspace Work in a well-ventilated area. Keep away from any flammable materials. 2. Checking the device Check the overall condition of the soldering lamp. Ensure there are no gas leaks. Check that the tip is clean and in good condition. 3. Filling the tank If necessary, fill the tank with the gas recommended for this model. Always do this while following safety instructions. 4. Starting up Slowly open the gas valve by turning the dedicated knob. Ignite the flame using a lighter or a flint by bringing the flame close to the tip. 5. Adjusting the flame Adjust the size and intensity of the flame with the adjustment knob. A blue flame is generally ideal for effective soldering. 6. Using for soldering Hold the soldering lamp at an appropriate angle to the piece being heated. Move the flame slowly to evenly heat the desired area. 7. Extinguishing and storing Close the gas valve to extinguish the flame once the work is finished. Allow the device to cool completely before storing it. Store the lamp in a dry place, away from heat and moisture. By following these steps, you ensure safe and optimal use of your DEXTER LM70235921 soldering lamp.

Q: What type of carbon to use for replacement on the DEXTER 350OS2.5 orbital sander?

To replace the carbon brushes of your DEXTER 350OS2.5 orbital sander, it is important to use brushes compatible with this model to ensure optimal operation and avoid damaging the device. Recommended type of carbon Most orbital sanders use graphite or carbon brushes, but the dimensions and shape may vary depending on the model. For the DEXTER 350OS2.5, it is advisable to use specific brushes that match its technical characteristics. How to choose and replace the brushes Check the dimensions: Measure the used brushes to find replacement parts of the same dimensions. Opt for quality brushes: Prefer original DEXTER brushes or certified equivalents to ensure compatibility and durability. Replacement: Always unplug the sander before intervening. Remove the old brushes by unscrewing the supports, then insert the new ones while respecting the polarity if applicable. Where to obtain the brushes You can find compatible brushes at authorized DEXTER service centers, specialized electric tool stores, or online on spare parts websites. Using suitable brushes ensures better performance and extends the lifespan of your orbital sander.

Question 1

Where to buy the laser or spare parts for the DEXTER DX254?

Accepted Answer

The integrated laser of the DEXTER DX254 (class 2, 650 nm, < 1 mW) is an important safety feature for cutting precision. To replace the laser or obtain spare parts, here are the solutions:

ADEO authorized service (manufacturer):

Contact ADEO service directly at: 135 rue Sadi Carnot, CS 00001, 59790 RONCHIN, FRANCE
You can also contact your Leroy Merlin store, which can initiate the request with ADEO service
For repairs or replacements of the laser, only the manufacturer or an authorized representative is allowed to intervene (to ensure compliance with safety standards)

Spare parts and accessories:

The common wear parts available are: motor brushes, 254 mm saw blade, table insert, and dust collector bag
Contact ADEO service to obtain the exact references of the parts you need
Ask specialized tool distributors for miter saws (check compatibility with the DX254 model before purchasing)

Important: Your saw comes with a manufacturer's warranty of 24 months for normal domestic use. If the laser no longer works or if you notice a failure and the product is still under warranty, first contact ADEO service or your Leroy Merlin dealer before purchasing a spare part. Repair costs may apply outside the warranty period.

Question 2

How to locate and use the laser on the DEXTER DX254 miter saw?

Accepted Answer

Location of the laser: The laser of your DEXTER DX254 miter saw is located on the machine head. It is controlled by the laser On/Off switch n°33, which is easily accessible on the machine's housing.

Activation and use: Press the switch n°33 once to activate the laser. A red laser beam will appear on the workpiece, indicating the cutting line in real-time. Press the same switch again to turn off the laser.

Adjusting the laser: If the laser beam no longer aligns correctly with the cutting line, you can adjust it. Loosen the crosshead screws (D) located near the laser module. Push the laser sideways until the laser beam precisely reaches the teeth of the saw blade (6). Once the alignment is correct, tighten the two crosshead screws firmly.

Laser maintenance: The laser operates on batteries. If you do not use the saw for an extended period, it is advisable to remove the batteries to prevent them from draining. If the beam weakens, simply replace the batteries.

Technical specifications: The laser complies with class 2 (wavelength: 650 nm, power less than 1 mW). It meets current safety standards and can only be repaired or replaced by the manufacturer or an authorized representative.

Essential safety instructions: Never look directly into the laser beam, even briefly. Never direct the beam at reflective surfaces, people, or animals, as even a low-power laser can cause eye damage. Never open the laser module yourself. Always protect your eyes when using the laser.

Question 3

Can I use smaller cutting discs on the DEXTER DP6 grinder?

Accepted Answer

Yes, but with important conditions.

The DEXTER DP6 model (2100AG2-230.5001) is designed for cutting discs with a diameter of 230 mm, but the technical manual indicates an accepted alternative: you can use 125 mm discs (maximum thickness 6 mm) on this device.

Essential conditions:

Compatible bore: The central hole must be 22.2 mm (M14) - this is the standard for this grinder
Thickness: For 125 mm discs, the maximum allowed thickness is 6 mm
Rotation speed: This grinder operates at a maximum of 6,500 RPM. You must ensure that the smaller disc does not exceed this limit (smaller discs often have a higher maximum speed)
Type of disc: For cutting discs, only diamond and reinforced bonded versions are accepted according to the manual

With a power of 2100W, your device has the necessary power for 125 mm discs without any issues.

Question 4

How to install the protective guard on the Dexter 800AG2-125.5001 angle grinder?

Accepted Answer

To correctly install the protective guard on your Dexter 800AG2-125.5001 angle grinder, follow the steps below:

Steps to install the protective guard:

Ensure that the grinder is turned off and unplugged from any power source to ensure your safety.
Release the locking lever of the guard by pulling it outward.
Position the guard on the grinder's spindle by rotating or adjusting it to the desired angle.
Close the locking lever by pushing it to secure the guard in place.
Check that the raised edge of the guard is properly inserted into the notch on the bearing cap.

Important information:

The closed side of the guard should always face the operator for optimal protection.
The guard can be adjusted up to 45° to the left or right according to your needs.
To reposition the guard, unlock the lever, adjust the angle, and then lock it again.
Never use the grinder without the protective guard properly installed and locked.

Question 5

How to properly connect the suction hose to the DEXTER 710DWS2-225.1001 drywall sander?

Accepted Answer

To connect the suction hose to your DEXTER 710DWS2-225.1001 drywall sander, follow these precise steps:

Always unplug the sander before proceeding with the assembly to ensure your safety.
Loosen the sleeve of the dust extraction port (located on the upper extension shaft). Important: do not completely remove the sleeve, just loosen it.
Before attaching the sanding paper, precisely align the holes of the sanding paper with those of the base plate. This step is essential to ensure effective dust extraction and avoid air leaks.
Gently press the sanding paper to attach it to the base plate.
Insert the suction hose connector into the dust extraction port until it reaches the stop. Make sure it is securely engaged.
Secure the connection by tightening the sleeve on the port. This step prevents any accidental disconnection of the hose during operation.
Then attach the other end of the hose to a suitable vacuum cleaner using the provided vacuum adapter. To remove the hose, simply loosen the sleeve, hold the handles, and pull the connector out of the port.

Important tip: The device can only be connected to one maximum extension tube. Aligning the holes of the sanding paper is crucial as it directly optimizes the suction flow and significantly reduces airborne dust.

Question 6

How to solve the problem of the laser not turning on the DEXTER DX216 miter saw?

Accepted Answer

If the laser of your DEXTER DX216 miter saw does not turn on, the problem usually comes from the batteries that power the laser module. Here’s how to resolve it:

1. Replace the laser batteries
The laser of the DEXTER DX216 operates on batteries. This is the most common cause of malfunction. Locate the battery compartment of the laser module (item 32) at the front of the saw and open it. Replace the batteries with new ones of the same type (usually AA or AAA batteries depending on the model). Ensure that the batteries are installed correctly, respecting the + and - polarities.

2. Check the laser On/Off switch
Press the laser On/Off switch (item 33) firmly once. A laser beam should then be projected onto the material to be cut. If nothing happens after replacing the batteries, the switch may be defective.

3. Clean the laser lens
A buildup of dust or sawdust on the laser lens can prevent the beam from displaying correctly. Gently clean the lens with a dry, clean cloth. Avoid using abrasive products that could scratch the optical lens.

4. Check the overall power supply of the saw
Make sure that the miter saw is properly plugged in and that the main switch of the machine is in the ON position. An unpowered saw will not have a functional laser, even if the device starts.

5. Contact customer service if the issue persists
If after replacing the batteries and cleaning the laser remains non-functional, this may indicate a defect in the laser module. Laser repairs can only be performed by the manufacturer or an authorized representative. Contact ADEO customer service at: 135 RUE SADI CARNOT CS00001, 59790 RONCHIN, FRANCE. The product is guaranteed for 24 months against manufacturing defects.

Question 7

What should I do if my DEXTER 300DS2.5 sander does not turn on?

Accepted Answer

If your DEXTER 300DS2.5 sander does not turn on, several checks can help you identify and resolve the issue:

1. Check the power supply

Make sure the sander is properly plugged into a functional electrical outlet.
Test the outlet with another device to confirm it is delivering power.

2. Check the power cord

Inspect the cord for cuts, exposed wires, or signs of wear.
A damaged cord may prevent the sander from turning on and should be repaired or replaced.

3. Check the switch

Ensure that the switch is in the

Question 8

Do the DEXTER cordless drills 12SD2-25RC.1A, 20SD2-35RC.2A, and 20SD2-35RC.2B have a hammer mode?

Accepted Answer

The DEXTER cordless drills models 12SD2-25RC.1A, 20SD2-35RC.2A, and 20SD2-35RC.2B are generally not equipped with a hammer mode. These models are primarily designed for drilling and screwing in standard materials such as wood, plastic, or metal, but do not have the hammer function that is useful for drilling into harder materials like brick or concrete.

The hammer mode allows the drill to make quick, small blows in addition to rotation, thus facilitating drilling into hard materials. The absence of this function means that these models are better suited for light to medium tasks and are not suitable for work requiring hammer drilling.

If you need a drill with a hammer mode, it is advisable to look for a model specifically designed for that, often referred to as a "hammer drill" or "combination drill."

Question 9

How to properly use the DEXTER LM70235921 soldering lamp?

Accepted Answer

To properly use the DEXTER LM70235921 soldering lamp, follow these essential steps to ensure safe and effective use:

1. Preparing the workspace

Work in a well-ventilated area.
Keep away from any flammable materials.

2. Checking the device

Check the overall condition of the soldering lamp.
Ensure there are no gas leaks.
Check that the tip is clean and in good condition.

3. Filling the tank

If necessary, fill the tank with the gas recommended for this model.
Always do this while following safety instructions.

4. Starting up

Slowly open the gas valve by turning the dedicated knob.
Ignite the flame using a lighter or a flint by bringing the flame close to the tip.

5. Adjusting the flame

Adjust the size and intensity of the flame with the adjustment knob.
A blue flame is generally ideal for effective soldering.

6. Using for soldering

Hold the soldering lamp at an appropriate angle to the piece being heated.
Move the flame slowly to evenly heat the desired area.

7. Extinguishing and storing

Close the gas valve to extinguish the flame once the work is finished.
Allow the device to cool completely before storing it.
Store the lamp in a dry place, away from heat and moisture.

By following these steps, you ensure safe and optimal use of your DEXTER LM70235921 soldering lamp.

Question 10

What type of carbon to use for replacement on the DEXTER 350OS2.5 orbital sander?

Accepted Answer

To replace the carbon brushes of your DEXTER 350OS2.5 orbital sander, it is important to use brushes compatible with this model to ensure optimal operation and avoid damaging the device.

Recommended type of carbon

Most orbital sanders use graphite or carbon brushes, but the dimensions and shape may vary depending on the model. For the DEXTER 350OS2.5, it is advisable to use specific brushes that match its technical characteristics.

How to choose and replace the brushes

Check the dimensions: Measure the used brushes to find replacement parts of the same dimensions.
Opt for quality brushes: Prefer original DEXTER brushes or certified equivalents to ensure compatibility and durability.
Replacement: Always unplug the sander before intervening. Remove the old brushes by unscrewing the supports, then insert the new ones while respecting the polarity if applicable.

Where to obtain the brushes

You can find compatible brushes at authorized DEXTER service centers, specialized electric tool stores, or online on spare parts websites.

Using suitable brushes ensures better performance and extends the lifespan of your orbital sander.

User manual DEXTER : user manuals and guides in PDF

Models DEXTER most viewed

Browse manuals DEXTER by appliance type

Recent questions about devices DEXTER