Q: Where to buy the laser or spare parts for the DEXTER DX254?

The integrated laser of the DEXTER DX254 (class 2, 650 nm, ADEO authorized service (manufacturer): Contact ADEO service directly at: 135 rue Sadi Carnot, CS 00001, 59790 RONCHIN, FRANCE You can also contact your Leroy Merlin store, which can initiate the request with ADEO service For repairs or replacements of the laser, only the manufacturer or an authorized representative is allowed to intervene (to ensure compliance with safety standards) Spare parts and accessories: The common wear parts available are: motor brushes, 254 mm saw blade, table insert, and dust collector bag Contact ADEO service to obtain the exact references of the parts you need Ask specialized tool distributors for miter saws (check compatibility with the DX254 model before purchasing) Important: Your saw comes with a manufacturer's warranty of 24 months for normal domestic use. If the laser no longer works or if you notice a failure and the product is still under warranty, first contact ADEO service or your Leroy Merlin dealer before purchasing a spare part. Repair costs may apply outside the warranty period.

Q: How to locate and use the laser on the DEXTER DX254 miter saw?

Location of the laser: The laser of your DEXTER DX254 miter saw is located on the machine head. It is controlled by the laser On/Off switch n°33 , which is easily accessible on the machine's housing. Activation and use: Press the switch n°33 once to activate the laser. A red laser beam will appear on the workpiece, indicating the cutting line in real-time. Press the same switch again to turn off the laser. Adjusting the laser: If the laser beam no longer aligns correctly with the cutting line, you can adjust it. Loosen the crosshead screws (D) located near the laser module. Push the laser sideways until the laser beam precisely reaches the teeth of the saw blade (6). Once the alignment is correct, tighten the two crosshead screws firmly. Laser maintenance: The laser operates on batteries. If you do not use the saw for an extended period, it is advisable to remove the batteries to prevent them from draining. If the beam weakens, simply replace the batteries. Technical specifications: The laser complies with class 2 (wavelength: 650 nm, power less than 1 mW). It meets current safety standards and can only be repaired or replaced by the manufacturer or an authorized representative. Essential safety instructions: Never look directly into the laser beam, even briefly. Never direct the beam at reflective surfaces, people, or animals, as even a low-power laser can cause eye damage. Never open the laser module yourself. Always protect your eyes when using the laser.

Q: How to solve the problem of the laser not turning on the DEXTER DX216 miter saw?

If the laser of your DEXTER DX216 miter saw does not turn on, the problem usually comes from the batteries that power the laser module. Here’s how to resolve it: 1. Replace the laser batteries The laser of the DEXTER DX216 operates on batteries. This is the most common cause of malfunction. Locate the battery compartment of the laser module (item 32) at the front of the saw and open it. Replace the batteries with new ones of the same type (usually AA or AAA batteries depending on the model). Ensure that the batteries are installed correctly, respecting the + and - polarities. 2. Check the laser On/Off switch Press the laser On/Off switch (item 33) firmly once. A laser beam should then be projected onto the material to be cut. If nothing happens after replacing the batteries, the switch may be defective. 3. Clean the laser lens A buildup of dust or sawdust on the laser lens can prevent the beam from displaying correctly. Gently clean the lens with a dry, clean cloth. Avoid using abrasive products that could scratch the optical lens. 4. Check the overall power supply of the saw Make sure that the miter saw is properly plugged in and that the main switch of the machine is in the ON position. An unpowered saw will not have a functional laser, even if the device starts. 5. Contact customer service if the issue persists If after replacing the batteries and cleaning the laser remains non-functional, this may indicate a defect in the laser module. Laser repairs can only be performed by the manufacturer or an authorized representative. Contact ADEO customer service at: 135 RUE SADI CARNOT CS00001, 59790 RONCHIN, FRANCE. The product is guaranteed for 24 months against manufacturing defects.

Q: How to use and adjust the laser on the DEXTER DX216 miter saw?

The DEXTER DX216 miter saw is equipped with a class 2 laser (wavelength 650 nm) that projects a visible line on the material to precisely indicate where the blade will cut. The laser is controlled via the On/Off switch (reference 33) located on the body of the machine. To use the laser: Press the On/Off switch of the laser (33) once. The laser beam immediately projects onto the piece of wood or material and indicates exactly the cutting line. You can then position your material so that the laser precisely follows your desired cutting line. To stop the laser, press the switch (33) again. To adjust the laser if the line is not accurate: If the laser (32) no longer perfectly aligns with the blade's path, you need to readjust it. Start by loosening the two crosshead screws (D) located near the laser module. Then push the laser laterally (to the left or right) until the laser beam exactly reaches the teeth of the saw blade (6). Once adjusted, firmly re-tighten the two crosshead screws (D) to lock the laser's position. Important safety warnings: Never look directly at the laser beam without protection. Avoid directing the laser at reflective surfaces or towards people or animals, as even a class 2 laser beam can cause harm. Never open the laser module itself and do not attempt to replace it with another model. Laser repairs should only be carried out by the laser manufacturer or an authorized representative. Turn off the laser when not in use.

Q: How to adjust the table of the DEXTER DX216 miter saw for precise cuts?

To adjust the table of your DEXTER DX216 miter saw and ensure precise cuts, follow these steps: 1. Preparation Make sure the saw is unplugged to avoid any risk of accident. Place the saw on a stable and flat surface. 2. Unlocking the table Locate the lever or locking knob of the table, usually found at the back or on the side of the base. Unlock the table by operating this lever to allow it to pivot. 3. Adjusting the angle Rotate the table to the desired angle using the graduated markings on the base as a guide. For common angles, such as 45°, align the table precisely with the corresponding graduation. 4. Locking the table Once the angle is set, securely lock the table by returning the lever or knob to the locking position. 5. Checking the angle Use a square or protractor to verify that the angle of the table is correct. This check is essential to ensure the accuracy of your cuts. 6. Cutting test Plug the saw back in and make a test cut on a material similar to what you intend to work with. Check the cutting angle to confirm that the adjustment is correct. By following these steps, you will be able to effectively adjust the table of your DEXTER DX216 miter saw for clean and precise cuts.

Q: How to unlock the shaft of the DEXTER DX216 miter saw?

On the DEXTER DX216 miter saw, the drive shaft is equipped with a locking mechanism (element 30) that must be unlocked to access the spindle when changing the blade or making certain adjustments. Before any intervention, make sure to unplug the saw from the power outlet . This ensures your safety and prevents any accidental start-up. To unlock the drive shaft locking mechanism: Lift the machine head up and secure it with the safety stop (23) Keep the saw shaft lock (30) pressed down Slowly turn the flange screw (28) clockwise with a 6 mm Allen key After a maximum turn, the locking device will click, indicating that the mechanism is now released You can then freely access the shaft to replace the blade or make the necessary adjustment. Once the intervention is complete, reverse the steps to re-lock the shaft by turning the flange screw in the same direction until the locking mechanism clicks back into place. If the locking mechanism resists or does not click properly, do not force it - check that the flange screw is not too tight and that you are keeping the lock pressed down during rotation.

Question 1

Where to buy the laser or spare parts for the DEXTER DX254?

Accepted Answer

The integrated laser of the DEXTER DX254 (class 2, 650 nm, < 1 mW) is an important safety feature for cutting precision. To replace the laser or obtain spare parts, here are the solutions:

ADEO authorized service (manufacturer):

Contact ADEO service directly at: 135 rue Sadi Carnot, CS 00001, 59790 RONCHIN, FRANCE
You can also contact your Leroy Merlin store, which can initiate the request with ADEO service
For repairs or replacements of the laser, only the manufacturer or an authorized representative is allowed to intervene (to ensure compliance with safety standards)

Spare parts and accessories:

The common wear parts available are: motor brushes, 254 mm saw blade, table insert, and dust collector bag
Contact ADEO service to obtain the exact references of the parts you need
Ask specialized tool distributors for miter saws (check compatibility with the DX254 model before purchasing)

Important: Your saw comes with a manufacturer's warranty of 24 months for normal domestic use. If the laser no longer works or if you notice a failure and the product is still under warranty, first contact ADEO service or your Leroy Merlin dealer before purchasing a spare part. Repair costs may apply outside the warranty period.

Question 2

How to locate and use the laser on the DEXTER DX254 miter saw?

Accepted Answer

Location of the laser: The laser of your DEXTER DX254 miter saw is located on the machine head. It is controlled by the laser On/Off switch n°33, which is easily accessible on the machine's housing.

Activation and use: Press the switch n°33 once to activate the laser. A red laser beam will appear on the workpiece, indicating the cutting line in real-time. Press the same switch again to turn off the laser.

Adjusting the laser: If the laser beam no longer aligns correctly with the cutting line, you can adjust it. Loosen the crosshead screws (D) located near the laser module. Push the laser sideways until the laser beam precisely reaches the teeth of the saw blade (6). Once the alignment is correct, tighten the two crosshead screws firmly.

Laser maintenance: The laser operates on batteries. If you do not use the saw for an extended period, it is advisable to remove the batteries to prevent them from draining. If the beam weakens, simply replace the batteries.

Technical specifications: The laser complies with class 2 (wavelength: 650 nm, power less than 1 mW). It meets current safety standards and can only be repaired or replaced by the manufacturer or an authorized representative.

Essential safety instructions: Never look directly into the laser beam, even briefly. Never direct the beam at reflective surfaces, people, or animals, as even a low-power laser can cause eye damage. Never open the laser module yourself. Always protect your eyes when using the laser.

Question 3

How to solve the problem of the laser not turning on the DEXTER DX216 miter saw?

Accepted Answer

If the laser of your DEXTER DX216 miter saw does not turn on, the problem usually comes from the batteries that power the laser module. Here’s how to resolve it:

1. Replace the laser batteries
The laser of the DEXTER DX216 operates on batteries. This is the most common cause of malfunction. Locate the battery compartment of the laser module (item 32) at the front of the saw and open it. Replace the batteries with new ones of the same type (usually AA or AAA batteries depending on the model). Ensure that the batteries are installed correctly, respecting the + and - polarities.

2. Check the laser On/Off switch
Press the laser On/Off switch (item 33) firmly once. A laser beam should then be projected onto the material to be cut. If nothing happens after replacing the batteries, the switch may be defective.

3. Clean the laser lens
A buildup of dust or sawdust on the laser lens can prevent the beam from displaying correctly. Gently clean the lens with a dry, clean cloth. Avoid using abrasive products that could scratch the optical lens.

4. Check the overall power supply of the saw
Make sure that the miter saw is properly plugged in and that the main switch of the machine is in the ON position. An unpowered saw will not have a functional laser, even if the device starts.

5. Contact customer service if the issue persists
If after replacing the batteries and cleaning the laser remains non-functional, this may indicate a defect in the laser module. Laser repairs can only be performed by the manufacturer or an authorized representative. Contact ADEO customer service at: 135 RUE SADI CARNOT CS00001, 59790 RONCHIN, FRANCE. The product is guaranteed for 24 months against manufacturing defects.

Question 4

How to use and adjust the laser on the DEXTER DX216 miter saw?

Accepted Answer

The DEXTER DX216 miter saw is equipped with a class 2 laser (wavelength 650 nm) that projects a visible line on the material to precisely indicate where the blade will cut. The laser is controlled via the On/Off switch (reference 33) located on the body of the machine.

To use the laser: Press the On/Off switch of the laser (33) once. The laser beam immediately projects onto the piece of wood or material and indicates exactly the cutting line. You can then position your material so that the laser precisely follows your desired cutting line. To stop the laser, press the switch (33) again.

To adjust the laser if the line is not accurate: If the laser (32) no longer perfectly aligns with the blade's path, you need to readjust it. Start by loosening the two crosshead screws (D) located near the laser module. Then push the laser laterally (to the left or right) until the laser beam exactly reaches the teeth of the saw blade (6). Once adjusted, firmly re-tighten the two crosshead screws (D) to lock the laser's position.

Important safety warnings: Never look directly at the laser beam without protection. Avoid directing the laser at reflective surfaces or towards people or animals, as even a class 2 laser beam can cause harm. Never open the laser module itself and do not attempt to replace it with another model. Laser repairs should only be carried out by the laser manufacturer or an authorized representative. Turn off the laser when not in use.

Question 5

How to fix the laser that won't turn on for a DEXTER DX254 miter saw?

Accepted Answer

If the laser of your DEXTER DX254 miter saw won't turn on, the problem usually comes from poor battery power or a misaligned switch. The laser of the DX254 operates on a separate battery, distinct from the saw's electrical power.

First check: the laser switch

Locate the laser On/Off switch (component 33) on the saw.
Press this switch firmly once to turn the laser on. A red laser beam should appear on the workpiece.
If nothing happens, the switch may be stuck or defective.

Second check: the laser batteries

Access the battery compartment of the laser module (usually accessible via a small panel).
Check the condition of the batteries: ensure they are not depleted, corroded, or improperly positioned.
If the batteries are old or worn out, replace them with new batteries of the same type.
If the device has not been used for a long time, the batteries should be removed to prevent corrosion. Install new batteries.

Third check: the laser alignment

If the laser turns on but does not turn off, or does not indicate the cutting line correctly, the alignment may be off.
Loosen the two Phillips screws (D) slightly located near the laser module.
Push the laser sideways until the laser beam precisely reaches the teeth of the blade.
Tighten the two screws firmly to secure the alignment.

If the laser still does not work

The laser module of the DX254 is a sealed component and should never be opened.
Laser repairs can only be performed by the laser manufacturer or an authorized representative. Contact DEXTER customer service for diagnosis or replacement.

Safety advice: Never look directly into the laser beam, even if its power is low. Protect your eyes when working with the laser activated.

Question 6

How to adjust the table of the DEXTER DX216 miter saw for precise cuts?

Accepted Answer

To adjust the table of your DEXTER DX216 miter saw and ensure precise cuts, follow these steps:

1. Preparation

Make sure the saw is unplugged to avoid any risk of accident.
Place the saw on a stable and flat surface.

2. Unlocking the table

Locate the lever or locking knob of the table, usually found at the back or on the side of the base.
Unlock the table by operating this lever to allow it to pivot.

3. Adjusting the angle

Rotate the table to the desired angle using the graduated markings on the base as a guide.
For common angles, such as 45°, align the table precisely with the corresponding graduation.

4. Locking the table

Once the angle is set, securely lock the table by returning the lever or knob to the locking position.

5. Checking the angle

Use a square or protractor to verify that the angle of the table is correct.
This check is essential to ensure the accuracy of your cuts.

6. Cutting test

Plug the saw back in and make a test cut on a material similar to what you intend to work with.
Check the cutting angle to confirm that the adjustment is correct.

By following these steps, you will be able to effectively adjust the table of your DEXTER DX216 miter saw for clean and precise cuts.

Question 7

How to unlock the shaft of the DEXTER DX216 miter saw?

Accepted Answer

On the DEXTER DX216 miter saw, the drive shaft is equipped with a locking mechanism (element 30) that must be unlocked to access the spindle when changing the blade or making certain adjustments.

Before any intervention, make sure to unplug the saw from the power outlet. This ensures your safety and prevents any accidental start-up.

To unlock the drive shaft locking mechanism:

Lift the machine head up and secure it with the safety stop (23)
Keep the saw shaft lock (30) pressed down
Slowly turn the flange screw (28) clockwise with a 6 mm Allen key
After a maximum turn, the locking device will click, indicating that the mechanism is now released

You can then freely access the shaft to replace the blade or make the necessary adjustment. Once the intervention is complete, reverse the steps to re-lock the shaft by turning the flange screw in the same direction until the locking mechanism clicks back into place.

If the locking mechanism resists or does not click properly, do not force it - check that the flange screw is not too tight and that you are keeping the lock pressed down during rotation.

User manual DEXTER Miter saw : user manuals and guides in PDF

Models DEXTER Miter saw most viewed

Other categories DEXTER

Recent questions about Miter saw DEXTER