Q: The frame supports of the Amber IV bike rack are too narrow - how can I widen them?

If the frame supports (halterungen) of the Eufab Amber IV bike rack seem too narrow to accommodate your bikes, here’s how to proceed: Main adjustment points The quick-release lever located at the base of the support (at the attachment point on the tow ball) allows for tension adjustment. Ensure that this lever is properly lowered to the stop (with a force of 35-40 kg) and fully locked - improper tightening can give the impression that the supports are too narrow. The fine adjustment screw (covered by a removable protective cap) allows for additional adjustment if necessary after the initial installation. Check if this screw is accessible and can be slightly unscrewed to increase the internal space of the supports. Before forcing your frames, also ensure that you place the first bike in the rail closest to the vehicle, and that you are using the frame holding straps (U-bracket) correctly - they should support the frame without excessive tightening. If after these checks the supports remain too narrow for your wider bike frames, the support may be limited by its design for the intended frame category. Feel free to contact Eufab support to confirm compatibility with your type of frame.

Question 1

What to do if the 13-pin connector cables are damaged or torn?

Accepted Answer

The Eufab Amber IV uses a standard 13-pin electrical connector to power the rear lights of the bike carrier. If the cables are damaged or torn from the socket, here’s how to proceed:

Verification and Diagnosis

Start by inspecting the cables and the 13-pin connector. According to the manual, the cables should always be laid along the base chassis and must never be bent, stretched, or crushed. If the cables show visible damage, they will need to be replaced.

Correct Installation of Cables

When reassembling or repairing, follow these important points:

Lay the cables along the base chassis of the bike carrier
Secure them firmly with the provided cable ties
Do not leave the cables loose or exposed
Ensure that the cables do not interfere with the tilting mechanism of the bike carrier

Replacement of Cables

If the cables are too damaged to be repaired, you will need to have the entire electrical system replaced. Contact an authorized towing service or the manufacturer to obtain replacement cables that comply with the product's 13-pin specifications. Since the Amber IV is an electrical device, the repair must comply with automotive safety standards.

Question 2

The frame supports of the Amber IV bike rack are too narrow - how can I widen them?

Accepted Answer

If the frame supports (halterungen) of the Eufab Amber IV bike rack seem too narrow to accommodate your bikes, here’s how to proceed:

Main adjustment points

The quick-release lever located at the base of the support (at the attachment point on the tow ball) allows for tension adjustment. Ensure that this lever is properly lowered to the stop (with a force of 35-40 kg) and fully locked - improper tightening can give the impression that the supports are too narrow.
The fine adjustment screw (covered by a removable protective cap) allows for additional adjustment if necessary after the initial installation. Check if this screw is accessible and can be slightly unscrewed to increase the internal space of the supports.

Before forcing your frames, also ensure that you place the first bike in the rail closest to the vehicle, and that you are using the frame holding straps (U-bracket) correctly - they should support the frame without excessive tightening.

If after these checks the supports remain too narrow for your wider bike frames, the support may be limited by its design for the intended frame category. Feel free to contact Eufab support to confirm compatibility with your type of frame.

Question 3

The Austrian red license plate does not fit in the bike rack holder - how can I solve this problem?

Accepted Answer

The Eufab Amber IV does not have an integrated license plate holder that automatically adjusts to different plate formats. Austrian red plates (in the typical rectangular format) may be too wide for the intended holder if it is sized according to standard German norms.

Possible solutions:

Check the orientation: Try positioning the plate differently or check that it does not hit the bike rack rails during installation.
License plate adapter holder: Contact Eufab directly to request a universal license plate holder or an adapter capable of accommodating Austrian format plates.
Temporary alternative: Use a magnetic license plate holder or a flexible frame compatible with Austrian plates, as long as it does not interfere with the locking and tilting of the bike rack.
Check before purchase: If you are considering a purchase, contact Eufab customer service or the retailer with the exact dimensions of your plate to confirm compatibility.

Feel free to contact the manufacturer with the precise dimensions of your plate for a solution tailored to your setup.

User manual Eufab : user manuals and guides in PDF

Models Eufab most viewed

Browse manuals Eufab by appliance type

Recent questions about devices Eufab