Q: How to use the Power button on the DENON AVR-1909 audio-video receiver?

The Power button on the DENON AVR-1909 audio-video receiver controls the device's power in two stages: standby and full power. Here’s how to use it correctly. Standby: Press the POWER button located on the front panel. The indicator light turns red, indicating that the device is entering standby mode. In this mode, the device consumes little energy but remains ready to start quickly. Full power: Once in standby mode, press the ON/STANDBY button (located on the front panel) or the [ON/SOURCE] button on the remote control. The indicator light blinks green and the device powers on completely. You can also turn on the device by pressing an input selection button (SOURCE SELECT) or a Quick Select button on the remote control. Turning off the device: To completely turn off the receiver, press the ON/STANDBY button on the front panel or the [OFF] button on the remote control. The device returns to standby mode with the red light on. Important: In standby mode, the device continues to consume a small amount of energy. For a complete disconnection from the power supply, unplug the power cord from the wall outlet, especially if you do not plan to use the device for an extended period. Indicator lights: The Power indicator located on the front panel allows you to check the device's status: red in standby mode, blinking green during startup, solid green once fully operational.

Question 1

How to resolve the issue of no sound from the center speaker of the DENON AVR-X1300W receiver?

Accepted Answer

If you are unable to get sound from the center speaker of your DENON AVR-X1300W receiver, here are several steps to follow to identify and resolve the issue:

1. Check the physical connections

Ensure that the center speaker cable is properly connected to the dedicated "Center" output at the back of the receiver.
Check that the cable is not damaged and that the connections are secure and clean.

2. Check the audio settings of the receiver

Access the audio setup menu via the remote control or the receiver's screen.
Make sure that the center speaker output is enabled and that the selected surround sound mode is using this speaker (for example, Dolby Digital, DTS, etc.).
Also check the volume level assigned to the center speaker to ensure it is not muted or too low.

3. Use the speaker test function

Use the "Test Speaker" or "Test Tone" function in the receiver's menu to send a sound signal to each speaker individually.
If the center speaker produces no sound during the test, this may indicate a hardware or wiring issue.

4. Check the audio source

Ensure that the audio source you are using (Blu-ray player, console, streaming, etc.) is outputting a surround signal that includes the center channel.
Some stereo content does not distribute sound to the center speaker.

5. Update the firmware

Check if a firmware update is available for your DENON AVR-X1300W receiver, as this may fix bugs related to audio management.

By following these steps, you should generally be able to identify the cause of the problem and restore sound to the center speaker. If the issue persists, it may be necessary to have the hardware checked by a professional.

Question 2

How to search for and save radio stations on the DENON Ceol RCDN10 receiver?

Accepted Answer

Your DENON Ceol RCDN10 receiver allows you to search for and save up to 50 FM or AM stations in its preset list. You have two methods: manual search and save, or automatic presetting (FM only).

Manual search and save of a station:

Press TUNER on the remote to select FM or AM
Use the TUNE + or TUNE – buttons to scroll through frequencies and find the desired station. The “a” indicator lights up as soon as a station is received
Once the station is found, press OPTION
Use the ui buttons to select Mem. Presets, then press ENTER
Select the number (1 to 50) where you want to save this station using the ui buttons, then press ENTER
The message Added appears to confirm the saving

Automatic presetting of all FM stations:

Press TUNER to select FM
Press OPTION
Select Mem. Auto Preset with the ui buttons, then press ENTER
Select Start and press ENTER
The device starts an automatic scan and presets all received FM stations. You can stop the process at any time by pressing the 2 button
When the search is complete, Finalize! appears. Note: AM stations cannot be automatically preset, and stations with a weak signal may not be detected

Listening to your saved stations:

Press OPTION at any time
Select Preset List with the ui buttons, then press ENTER
Scroll through your preset stations list with ui, select the one you want to listen to and press ENTER
Confirm with Play Now and press ENTER
You can also quickly navigate between preset stations by pressing the CH + and CH – buttons, or by using the numbers 0-9 and +10 to directly select a location

Deleting a station from your presets: Press OPTION, select Preset List, choose the station to delete, press ENTER, then select Remove from Preset List and confirm with ENTER. The message Removed confirms the deletion.

Question 3

How do I get sound from my DENON AVR-2309 receiver to my television via HDMI?

Accepted Answer

To get sound from your DENON AVR-2309 audio/video receiver to your television via HDMI, follow these steps:

1. Check the HDMI connections

Make sure the HDMI cable is properly connected between the ARC or HDMI Out port of your DENON receiver and the HDMI input of your television.

2. Set up your television

Select the HDMI input corresponding to the receiver on your television.
If your television supports the ARC (Audio Return Channel) function, enable it in the HDMI settings to allow audio transmission.

3. Configure the DENON AVR-2309 receiver

Turn on the receiver and access the setup menu using the remote control (press the Setup button).
In the HDMI or audio settings, ensure that the HDMI audio output is enabled.
If you want the sound to come out through the television, make sure the HDMI Audio Out function is set to TV or On, depending on the available options.

4. Check the audio source

If you are using an external source (Blu-ray player, console, etc.) connected to the receiver, ensure that it is sending audio via HDMI.

5. Test the setup

Start audio or video playback on your source to check that the sound is correctly transmitted to your television via the receiver.

By following these steps, you should be able to enjoy the sound from your DENON AVR-2309 directly on your television via HDMI.

Question 4

How to use a replacement remote control RC-978 with a DENON AVR-1906 receiver?

Accepted Answer

To use a replacement remote control RC-978 with your DENON AVR-1906 audio/video receiver, follow these simple steps:

1. Install the batteries correctly

Make sure the remote control is equipped with new batteries and that they are inserted respecting the indicated polarity (+ and -).

2. Turn on the receiver

Before using the remote control, turn on your DENON AVR-1906 manually or via the power button on the receiver.

3. Test the basic functions

Try the main commands such as adjusting the volume, changing the source (TV, DVD, etc.), and muting.
Also check access to the menus and navigation within them.

4. Program specific functions if necessary

If some buttons do not work as expected, the remote control may require specific programming or pairing with your receiver model. Refer to the instructions provided with the RC-978 remote control to learn how to program the codes corresponding to your DENON AVR-1906.

5. Check the range and orientation

Ensure that the remote control is aimed at the infrared sensor of the receiver and that you are at a reasonable distance (usually less than 7 meters).

By following these steps, your replacement remote control RC-978 should work properly with your DENON AVR-1906. If some buttons remain inactive, it may be helpful to test another compatible remote control or check the exact compatibility of the RC-978 model with your device.

Question 5

How to solve the sound loss issue on the DENON AVR-3313 AV receiver?

Accepted Answer

If your DENON AVR-3313 AV receiver is not producing sound, here are several steps to diagnose and resolve the issue:

1. Check the physical connections

Ensure that all audio cables are properly connected between the receiver and the speakers.
Check that the audio source (TV, DVD player, console, etc.) is properly connected to the receiver.

2. Check the receiver settings

Make sure you have selected the correct input source on the receiver.
Ensure that the volume is not set to minimum or muted. Increase the volume using the remote control or the buttons on the device.

3. Examine the audio settings

Access the audio setup menu to verify that the speakers are properly configured and activated.
Check that the audio mode is not muted or in a mode incompatible with your setup.

4. Restart the receiver

Turn off the receiver, unplug it from the power outlet for about 30 seconds, then plug it back in and turn it on to reset the temporary settings.

5. Test with another audio source

Connect another device (smartphone, MP3 player, etc.) to the receiver to check if the issue comes from the source or the receiver itself.

If after these checks the problem persists, it is recommended to contact DENON customer service or a specialized technician for a thorough diagnosis.

Question 6

How to use the Power button on the DENON AVR-1909 audio-video receiver?

Accepted Answer

The Power button on the DENON AVR-1909 audio-video receiver controls the device's power in two stages: standby and full power. Here’s how to use it correctly.

Standby: Press the POWER button located on the front panel. The indicator light turns red, indicating that the device is entering standby mode. In this mode, the device consumes little energy but remains ready to start quickly.

Full power: Once in standby mode, press the ON/STANDBY button (located on the front panel) or the [ON/SOURCE] button on the remote control. The indicator light blinks green and the device powers on completely. You can also turn on the device by pressing an input selection button (SOURCE SELECT) or a Quick Select button on the remote control.

Turning off the device: To completely turn off the receiver, press the ON/STANDBY button on the front panel or the [OFF] button on the remote control. The device returns to standby mode with the red light on.

Important: In standby mode, the device continues to consume a small amount of energy. For a complete disconnection from the power supply, unplug the power cord from the wall outlet, especially if you do not plan to use the device for an extended period.

Indicator lights: The Power indicator located on the front panel allows you to check the device's status: red in standby mode, blinking green during startup, solid green once fully operational.

Question 7

How to configure the DVD source on the DENON AVR-X1000 receiver for RCA wiring connection?

Accepted Answer

To configure the DVD source on your DENON AVR-X1000 receiver to work with an RCA wiring connection, you need to check and adjust the corresponding audio and video input settings.

Steps to configure the DVD source in RCA:

Turn on the receiver and press the Setup button on the remote control to access the setup menu.
Go to the input section: navigate to Input Setup or Input Configuration.
Select the DVD input corresponding to the socket where you have connected your DVD player.
Check the audio input type: make sure it is set to Analog or RCA so that the receiver can properly process the audio signal via the RCA cables.
Also check the video input if you are using a yellow RCA cable (composite): it should be set to Composite mode.
Save the changes and exit the menu.
Test the DVD source by selecting the DVD input on the receiver and playing a disc.

Additional tips:

Make sure the RCA cables are properly connected, in good condition, and in the correct sockets (left and right audio, composite video if applicable).
Check that the DVD player is turned on and functioning correctly.
Ensure that the receiver's volume is not muted or too low.

By following these steps, you should be able to use the DVD source with RCA wiring on your DENON AVR-X1000 without any issues.

Question 8

How to connect a DVD player to the DENON AVR-X1000 receiver using an RCA cable?

Accepted Answer

To connect a DVD player to your DENON AVR-X1000 audio/video receiver using an RCA cable, follow these simple steps:

Required materials:

An RCA cable (with red and white connectors for audio, and yellow for video if you want to transmit the image)

Connection steps:

Identify the RCA outputs on your DVD player: You will usually find three jacks: red (right audio), white (left audio), and yellow (video).
Plug the RCA cable into the DVD player: Connect the red, white, and yellow plugs of the cable to the corresponding outputs of the DVD player.
Locate the RCA inputs on the DENON AVR-X1000: On the back panel of the receiver, find the RCA audio and video inputs, often grouped under the label "DVD" or "Video."
Connect the RCA cable to the receiver: Connect the red, white, and yellow plugs to the corresponding inputs of the DENON AVR-X1000.
Power on the devices: Turn on the DVD player and the receiver.
Select the appropriate source on the receiver: Use the DENON remote control to choose the input corresponding to the DVD connection (often labeled "DVD" or "Video").

Additional tips:

Make sure the cables are properly inserted and that the colors match correctly.
Adjust the receiver's volume to an audible level to test the sound.
If you do not see an image or hear sound, check the source selection and the cable connections.

This method will allow you to enjoy the sound and image from your DVD player through your DENON AVR-X1000 receiver using a standard RCA wiring.

Question 9

How to connect a phone to the DENON AVR-3803 audio-video receiver?

Accepted Answer

To connect a phone to the DENON AVR-3803 audio-video receiver, you need to use a wired connection with a 3.5 mm audio jack to RCA cable. The DENON AVR-3803 is equipped with several audio inputs that accept this type of connection.

Preparing the equipment: You will need a stereo 3.5 mm jack to two RCA plugs (red and white) cable. This cable is available at audio or electronics stores. Make sure your phone has a 3.5 mm headphone jack output, as this connection is not possible on devices that only have USB-C or Lightning ports without an adapter.

Choosing the appropriate audio input: The DENON AVR-3803 offers several audio inputs that can accommodate your phone. The most convenient are the CDR/TAPE input (for playback) or the V.AUX input (video auxiliary, which also accepts audio signals). You can also use the CD input if you are not using it for a CD player.

Connecting the cable: Plug the 3.5 mm jack of the cable into the headphone jack of your phone. Then connect the two RCA plugs (red for the right channel, white for the left channel) into the chosen input at the back of the receiver. Ensure that the connections are firmly inserted to avoid noise interference.

Selecting the input on the receiver: On the remote control of the DENON AVR-3803, use the SOURCE button or the input selection buttons to choose the input corresponding to where you plugged in the cable (for example, CDR/TAPE or V.AUX). The name of the input will be displayed on the receiver's control screen.

Playing music: Open your phone's music app and start playback. Use the MASTER VOLUME (volume knob) of the receiver to adjust the sound level. If the sound is very low or distorted, check that the RCA connections are firmly inserted and that the cable is not defective.

Important note: Avoid plugging or unplugging the cable while the receiver is operating, as this can generate loud noises and damage the speakers. Always wait for the receiver to be turned off before making any wiring changes.

User manual DENON AV receiver : user manuals and guides in PDF

Models DENON AV receiver most viewed

Other categories DENON

Recent questions about AV receiver DENON