Q: How to adjust the pressure on the KARCHER K3800 ECO pressure washer?

The KARCHER K3800 ECO pressure washer is equipped with a continuously adjustable pressure lance that allows you to adapt the cleaning power to your needs. Adjustment Procedure Release the trigger handle Turn the lance to the desired position between 'Min' and 'Max' The operating pressure is continuously adjustable between these two positions Technical Specifications Operating pressure: 11 MPa Maximum allowable pressure: 12 MPa Flow rate: 6.3 l/min Tip: In economy mode (ECO), this function allows for a reduction of about 20% in water and electricity consumption. For use with detergent, turn the lance to the 'Mix' position to mix the detergent with the water jet.

Q: How to connect the high-pressure hose to the KARCHER K4 PREMIUM gun?

To connect the hose to the KARCHER K4 PREMIUM gun: Completely unroll the high-pressure hose from the reel while holding it by the transport handle. Insert the hose into the gun handle until it clicks audibly. You will hear a "click" or "clack" indicating a secure connection. Check the connection by gently pulling on the hose to ensure it is locked in place. Important points: The hose must be fully unrolled before connecting to avoid twisting. Ensure that the hose connector aligns correctly with the gun connector. Only disconnect the hose from the gun when there is no pressure left in the system (after the device has been turned off). The K4 PREMIUM is equipped with a reinforced hose with a diameter of 13 mm and a minimum length of 7.5 m, designed to operate up to 13 MPa.

Q: What to do in case of a water leak on my KARCHER K 6.90 M pressure washer?

A minor leak can occur under certain conditions of use. Here’s how to identify and resolve the issue on your KARCHER K 6.90 M: Check the connections The first step is to properly tighten all the fittings: The water inlet fitting The quick coupling for the high-pressure hose The connections of the detergent suction hose Check the condition of the seals Examine the seals to see if they are damaged or worn. If so, they need to be replaced. Bleed the system Run the device without the high-pressure hose to evacuate air from the lines. This may resolve some leaks caused by air pressure. If the leak persists If after these checks the leak continues or is significant, contact an authorized after-sales service. Only a certified technician can intervene on the internal components of your device.

Question 1

How to adjust the pressure on the KARCHER K3800 ECO pressure washer?

Accepted Answer

The KARCHER K3800 ECO pressure washer is equipped with a continuously adjustable pressure lance that allows you to adapt the cleaning power to your needs.

Adjustment Procedure

Release the trigger handle
Turn the lance to the desired position between 'Min' and 'Max'
The operating pressure is continuously adjustable between these two positions

Technical Specifications

Operating pressure: 11 MPa
Maximum allowable pressure: 12 MPa
Flow rate: 6.3 l/min

Tip: In economy mode (ECO), this function allows for a reduction of about 20% in water and electricity consumption. For use with detergent, turn the lance to the 'Mix' position to mix the detergent with the water jet.

Question 2

Does the BPP 4000 48 pump stop automatically once the tank is full or empty?

Accepted Answer

Yes, the pump stops automatically once the operating pressure is reached. The pressure switch cuts off the motor once the tank is full and the shut-off pressure is established in the system.

However, the cleaner does not stop automatically when the tank is empty without additional accessories. Two optional options can secure the operation:

Dry run protection (ref. 6.997-355.0) - protects the pump and automatically turns it off if there is no water circulating.
Float switch (ref. 6.997-356.0) - automatically turns the pump on and off based on the water tank level.

The BPP 4000 48 also includes a built-in thermal protection: the power supply is interrupted in case of overheating via a thermal contact.

Question 3

How do I stop the jet from my lance on the KARCHER 720 MX when the trigger is not working anymore?

Accepted Answer

If the trigger on your KARCHER 720 MX is stuck and water continues to flow, you have several immediate solutions to stop the jet while waiting for a repair.

Your device has three safety systems to stop the water: the pressure switch (which automatically cuts off the pump when you release the trigger), the mechanical safety stop on the gun handle, and a pressure relief valve that protects against pressure spikes beyond 150 bars. If the trigger is stuck in the open position, these systems may not function properly.

Here’s how to immediately stop the jet:

Turn off the main water tap. This is the most direct and safest solution. Turn the water tap that supplies your device (at home or on the inlet hose) to completely cut off the water supply. The jet will stop immediately.
Disconnect the water inlet hose. If you do not have access to the tap, simply unplug the water supply hose from the device to interrupt the supply.
Turn off the device. Switch the main switch to position 0 to stop the motor and the pump.
Press the safety stop button. This safety button located on the gun handle normally prevents any accidental start and can help you keep the device secure.

To diagnose and clean before a repair: gently clean the safety stop and the trigger mechanism with a damp cloth. Limescale deposits can sometimes block the mechanism. If the problem comes from the pressure switch (the automatic stop system), this component requires professional intervention.

If in doubt or if no solution works, contact an authorized Kärcher dealer or customer service for a repair. KARCHER recommends using only original spare parts to ensure the safety and proper functioning of your high-pressure cleaner.

Question 4

How to reassemble the connection box on a KARCHER K 6.90 M?

Accepted Answer

The PDF of this manual does not specify the detailed steps for reassembling the connection box after disassembly. However, according to the KARCHER K 6.90 M manual, the connection box must be properly connected to both circuits:

Electrical Connection

Required Voltage: 230-240 V, 1~50 Hz, 16 A (time delay)
Protection Class: I
Safety: A residual current circuit breaker (max. 30 mA) is recommended
Installation: The device must only be connected by an electrician in accordance with IEC 60364 standards

Water Connection

Connection: Screw the supplied connector onto the water inlet of the device
Hose: Attach the reinforced water hose (minimum diameter 1/2 inch/13 mm) to the device's connector
Specifications: Max. temperature 60 °C, minimum flow 10 l/min, max. pressure 0.6 MPa

If you have disassembled the box for cleaning or inspection, ensure that the electrical and hydraulic connections are properly tightened before commissioning. In case of doubt or if you are not comfortable with the electrical connection, contact a qualified electrician.

Question 5

How to connect the high-pressure hose to the KARCHER K4 PREMIUM gun?

Accepted Answer

To connect the hose to the KARCHER K4 PREMIUM gun:

Completely unroll the high-pressure hose from the reel while holding it by the transport handle.
Insert the hose into the gun handle until it clicks audibly. You will hear a "click" or "clack" indicating a secure connection.
Check the connection by gently pulling on the hose to ensure it is locked in place.

Important points:

The hose must be fully unrolled before connecting to avoid twisting.
Ensure that the hose connector aligns correctly with the gun connector.
Only disconnect the hose from the gun when there is no pressure left in the system (after the device has been turned off).
The K4 PREMIUM is equipped with a reinforced hose with a diameter of 13 mm and a minimum length of 7.5 m, designed to operate up to 13 MPa.

Question 6

What to do in case of a water leak on my KARCHER K 6.90 M pressure washer?

Accepted Answer

A minor leak can occur under certain conditions of use. Here’s how to identify and resolve the issue on your KARCHER K 6.90 M:

Check the connections

The first step is to properly tighten all the fittings:

The water inlet fitting
The quick coupling for the high-pressure hose
The connections of the detergent suction hose

Check the condition of the seals

Examine the seals to see if they are damaged or worn. If so, they need to be replaced.

Bleed the system

Run the device without the high-pressure hose to evacuate air from the lines. This may resolve some leaks caused by air pressure.

If the leak persists

If after these checks the leak continues or is significant, contact an authorized after-sales service. Only a certified technician can intervene on the internal components of your device.

Question 7

How to change the jet type on the KARCHER K2 cleaner?

Accepted Answer

To change the jet type on your KARCHER K2, you need to change the lance (the nozzle) by detaching it and attaching a new one.

Procedure for changing the lance

Detach the current lance from the trigger handle by rotating it.
Choose the new lance according to your needs:
- High-pressure nozzle lance - for normal cleaning tasks
- Rotary nozzle lance - for stubborn dirt
Attach the new lance to the trigger handle by connecting it and rotating it to secure it tightly.

Important recommendations

Do not use the rotary nozzle on tires, the bodywork, or sensitive surfaces like wood, to avoid any damage. Also, maintain a distance of at least 30 cm between the lance and painted surfaces.

To apply detergent, detach the lance from the trigger handle and work only with the trigger handle alone, which allows the detergent to mix properly with the water jet.

Question 8

How to resolve a power loss with my Karcher K 4600?

Accepted Answer

A power loss on the K 4600 is generally due to a blockage in the high-pressure circuit. Here are the checks to perform in order:

1. Check the water supply

Make sure that the water flow is sufficient to supply the device. The K 4600 requires a minimum regular flow. Clean the water intake filter with running water to remove any blockage.

2. Purge the circuit

If air is present in the circuit, the pressure may be reduced. Start the device without the high-pressure hose connected and wait a few seconds until water flows regularly from the fitting.

3. Check the hose and nozzle

A blockage in the high-pressure hose or nozzle significantly reduces power. Inspect the hose for kinks or clogs. For the nozzle, clean the opening with a fine needle and rinse with running water.

4. Check the connections

Ensure that all high-pressure fittings are tight and that there are no leaks. A leak results in a significant power loss.

5. Adjust the Vario Power lance

The Vario Power lance of the K 4600 allows for continuous pressure adjustment. Make sure that the setting is not in the minimum position. Test at different positions.

If the power loss persists after all these checks, it may indicate an internal problem with the pump that requires professional inspection.

Question 9

Where can I find spare parts and accessories for my KARCHER 490 M?

Accepted Answer

The KARCHER 490 M is equipped with a 3-piston axial pump, a brass head cylinder, and multiple components that may require replacement over time. Here’s how to obtain the suitable spare parts for your cleaner.

Obtain the article number for your model

The first step is crucial: find the article number of your KARCHER 490 M. This number is located on the machine's nameplate (usually at the back or underneath the device). You can also check it in your user manual. With this number, you will be able to identify exactly the compatible original parts.

Commonly replaced parts

For this model, the following items are generally available as spare parts:

Gun and trigger (with integrated safety valve)
High-pressure hose (withstands 120 bar nominal pressure)
Wands and nozzles (for different cleaning degrees)
Water cartridge and seals
Water inlet filter
Complete pump and pumping parts

Where to order the parts

KARCHER offers original parts through its official network. Contact an authorized KARCHER dealer or check the KARCHER website for your country. Dealers specialized in high-pressure cleaning also have certified parts compatible with the 490 M. Prefer original parts to ensure safety (especially for seals and components that withstand the pressure of 400 l/h flow).

Question 10

Can the lance of the Kärcher K7 be immersed in water?

Accepted Answer

The Kärcher K7 manual does not explicitly mention that the entire lance can be immersed in water. However, here is what you need to know about using the K7 with water:

To fill the water circuit: use the supplied or compatible Kärcher suction hose with a check valve, and submerge it in a water reservoir (tank, basin, etc.). Fill the water hose before turning on the device.
Maximum water temperature: 60°C. Do not use hot water or water from the distribution network.
Electrical protection: maintain a safe distance between you and the device during use to avoid water splashes on electrical components.
Do not connect to the public network: the device must never be directly connected to the municipal drinking water system.

For precise confirmation on the total immersion of the lance, we recommend contacting Kärcher customer service, which can provide you with detailed information based on your setup.

User manual KARCHER Pressure washer : user manuals and guides in PDF

Models KARCHER Pressure washer most viewed

Other categories KARCHER

Recent questions about Pressure washer KARCHER