Q: How to start the Husqvarna 445 chainsaw?

Before starting , check that the chain brake is engaged, that all covers and the guide bar are properly installed, and that the machine is placed on a stable surface. Cold start procedure Pull the red control outward (up) to set the switch to the starter position Press the decompression valve to reduce cylinder pressure Press several times on the rubber pocket of the fuel pump until it fills (about 6 times) Hold the front handle with your left hand and position your right foot in the rear handle to stabilize the machine Slowly pull the starter cord until you feel resistance, then pull firmly and quickly As soon as the engine coughs, push the red starter control inward Continue pulling the cord until the engine starts completely To restart a hot engine , the procedure is simpler: just move the starter control up and down to establish an accelerated idle, then pull the starter as for a cold start. Safety - Never wrap the starter cord around your hand, do not pull it out completely, and always hold the machine with both hands during operation.

Question 1

How to start the Husqvarna 445 chainsaw?

Accepted Answer

Before starting, check that the chain brake is engaged, that all covers and the guide bar are properly installed, and that the machine is placed on a stable surface.

Cold start procedure

Pull the red control outward (up) to set the switch to the starter position
Press the decompression valve to reduce cylinder pressure
Press several times on the rubber pocket of the fuel pump until it fills (about 6 times)
Hold the front handle with your left hand and position your right foot in the rear handle to stabilize the machine
Slowly pull the starter cord until you feel resistance, then pull firmly and quickly
As soon as the engine coughs, push the red starter control inward
Continue pulling the cord until the engine starts completely

To restart a hot engine, the procedure is simpler: just move the starter control up and down to establish an accelerated idle, then pull the starter as for a cold start.

Safety - Never wrap the starter cord around your hand, do not pull it out completely, and always hold the machine with both hands during operation.

Question 2

Why won't the Husqvarna 236 chainsaw start in cold weather?

Accepted Answer

If the Husqvarna 236 chainsaw won't start in cold weather, it is usually due to improper application of the procedure. Follow these precise steps:

Cold Start Procedure

1. Engage the brake - Push the protective guard forward before starting.

2. Pump the fuel - Press several times on the rubber bulb of the fuel pump until the fuel starts to fill the bulb (do not fill it completely).

3. Adjust the choke (critical step) - Pull the blue choke/throttle control fully to the FULL CHOKE position. This is often the forgotten step that prevents starting. It automatically activates the fast idle.

4. Pull the starter - Hold the front handle with your left hand, keep the machine on the ground with your right foot, then pull the starter firmly and quickly until the engine starts.

5. Adjust the choke - As soon as the engine “fires up,” set the choke to the “1/2 choke” position and continue pulling the starter until it fully starts.

6. Warm up - Let the engine warm up for 30 seconds, then press the throttle to normalize the RPM.

Common Mistakes

Incorrectly positioned blue choke or only partially engaged instead of FULL CHOKE
Forgetting to pump the rubber bulb of the fuel pump before starting
Pulling the starter too slowly or without firmness

Follow the exact order of these steps and your Husqvarna 236 should start without issue in cold weather.

Question 3

What fuel-oil mixture should be used for the Husqvarna 236 chainsaw?

Accepted Answer

The Husqvarna 236 operates with a fuel-oil mixture for two-stroke engines. There are two mixing ratios depending on the type of oil used. The 1:50 (2%) ratio is recommended with Husqvarna two-stroke oil (optimal formulation for this engine), while the 1:33 (3%) ratio applies with other quality two-stroke oils classified as JASO FB or ISO EGB.

Dosages for 5 liters of fuel: With Husqvarna oil, pour 0.10 liters (100 ml) of oil. With another compatible two-stroke oil, pour 0.15 liters (150 ml) of oil. Always pour the oil into the fuel before refueling the chainsaw, and mix well by shaking the container to achieve a homogeneous emulsion.

Required fuel: Use high-quality unleaded or leaded fuel with a minimum octane rating of 90 RON. For work with continuous and high engine speeds (prolonged pruning, for example), a higher octane is recommended. Too low an octane can cause engine knocking, overheating, and serious engine damage.

Oils to absolutely avoid: Never use two-stroke oil for water-cooled engines (designated TCW for outboard oil), nor four-stroke oil. These incompatible oils can damage the engine and reduce the effectiveness of the catalyst.

Practical tips: Always fill the fuel tank and the chain oil tank at the same time, as their capacities are synchronized. Regularly clean the area around the fuel cap and tanks. Replace the fuel filter at least once a year. Before starting the chainsaw after refueling, move at least 3 meters away from the refueling point to avoid any risk of ignition.

Question 4

What is the correct fuel-oil mixing ratio for the HUSQVARNA 236 chainsaw?

Accepted Answer

The HUSQVARNA 236 chainsaw operates with a fuel-oil mixture. According to the manual, two ratios are possible depending on the type of oil used:

Mixing Ratios

Ratio 1:50 (2 %) with HUSQVARNA two-stroke oil
Ratio 1:33 (3 %) with other two-stroke oils classified JASO FB/ISO EGB

Practical Dosage

For 5 liters of fuel:

Ratio 1:50: add 100 ml of oil
Ratio 1:33: add 150 ml of oil

How to Prepare the Mixture

First, pour half of the fuel into a clean container approved for fuel, add all the oil, shake well, then pour in the rest of the fuel. The prepared mixture should be consumed within the month following.

Important: never use four-stroke oil or oil for outboard motors (TCW). The fuel must have a minimum octane rating of 90 (RON).

Question 5

Where is the air filter located on the HUSQVARNA 235 chainsaw?

Accepted Answer

The air filter of the HUSQVARNA 235 chainsaw is located on the side of the device, protected by a removable cover. To access it, follow these steps:

Turn off the chainsaw and ensure it is cool before any handling.
Locate the air filter cover, usually secured by clips or screws on the side of the chainsaw.
Remove the cover by unlocking the clips or unscrewing the screws with an appropriate screwdriver.
You will then see the air filter, which may be made of foam or paper.

It is important to regularly clean or replace this filter to ensure proper functioning and extend the lifespan of your chainsaw.

Question 6

How to reattach the switch spring on a Husqvarna 235 chainsaw?

Accepted Answer

To reattach the switch spring on your Husqvarna 235 chainsaw, follow these precise steps:

1. Safety first

Ensure that the chainsaw is turned off and that the spark plug is disconnected to prevent any accidental start-up.
Wear protective gloves to handle the parts safely.

2. Identifying the parts

Locate the switch lever and the switch spring. The spring is usually a small spiral-shaped spring or a piece of wire.

3. Positioning the spring

Place one end of the spring on the designated anchor point on the lever.
Gently stretch the spring to attach it to the other fixation point on the chassis or adjacent part.
Ensure that the spring is properly aligned and under sufficient tension to ensure the lever functions correctly.

4. Verification

Gently operate the lever to check that the spring provides the necessary tension and that the lever returns to its initial position.
If the lever does not operate correctly, check the positioning of the spring and adjust it if necessary.

This procedure restores the function of the switch on your Husqvarna 235 chainsaw by reattaching the lever spring.

Question 7

Where is the power button on the Husqvarna 235 chainsaw?

Accepted Answer

On the Husqvarna 235 chainsaw, the power button is located on the rear handle, on the right or left side depending on the exact model.

To locate it:

Look at the rear handle of the chainsaw, you will see a small lever or button dedicated to turning it on and off.
This button is often identifiable by symbols: a circle with a vertical line for the on position, and a circle with a line through it or a cross for the off position.

To start the chainsaw, toggle this button to the on position. To stop it, return it to the off position.

Note that the chain brake must be disengaged to safely start the machine.

Question 8

How do I adjust the chain oil flow on a Husqvarna 445 chainsaw?

Accepted Answer

To adjust the chain oil flow on your Husqvarna 445 chainsaw, follow these steps:

1. Preparation

Ensure that the chainsaw is turned off and placed on a stable surface.

2. Locating the oil reservoir

The oil reservoir is usually located on the side of the chainsaw, identifiable by a cap marked with an oil symbol.

3. Identifying the oil flow adjustment

On the Husqvarna 445 model, the oil flow is adjustable via a screw or lever located near the chain case or oil reservoir.

4. Adjusting the flow

Use a suitable screwdriver to turn the adjustment screw:

Turning clockwise increases the oil flow.
Turning counterclockwise decreases the flow.

5. Checking the adjustment

Start the chainsaw and let it run at idle.
Observe the rotating chain: a sufficient amount of oil should be visible to ensure proper lubrication.
If necessary, readjust the flow until optimal flow is achieved.

6. Safety

Once the adjustment is complete, ensure that the screw or lever is securely fastened to prevent loosening during use.

Proper adjustment of the oil flow is essential to extend the life of the chain and ensure effective and safe cutting.

User manual HUSQVARNA Chainsaw : user manuals and guides in PDF

Models HUSQVARNA Chainsaw most viewed

Other categories HUSQVARNA

Recent questions about Chainsaw HUSQVARNA