Q: Why doesn't my MOULINEX EZ855D fryer turn on (no noise, no light)?

Here are the checks to perform: Check the power supply: Make sure the wall outlet is working. Test it with another device (lamp, charger). Check that the voltage matches the 220-240 V ~ 50/60 Hz indicated on the device. Check the power cord: Inspect the cord for any visible cuts or damage. Try another outlet. Insert the drawer correctly: The EZ855D fryer has a safety system: it only operates if the cooking drawer is properly inserted all the way into the device. Remove and then reinsert the drawer firmly until you hear a click. Check the start button: Hold the Start/Pause button for at least 2 seconds. The device should then emit a sound signal and the display should light up. Wait after unplugging: If the device has been used recently, wait 5-10 minutes before trying again. A thermal protection system may temporarily keep it locked. Check the drawer safety: Clean the grooves of the drawer and those of the device body to remove any dust or debris that would prevent proper contact. If after these checks the device remains inert (still no noise or light), it is likely that there is an internal electrical fault requiring repair or replacement.

Q: My MOULINEX EZ855D fryer drawer is not working anymore, what should I do?

If your cooking drawer is not working on your MOULINEX EZ855D fryer, here are the points to check: Checks to make: Is the drawer properly inserted? Make sure that the cooking drawer (removable basket) is fully pushed into the device until it clicks. Incorrect positioning prevents the device from functioning. Is the drawer overfilled? The manual specifies never to exceed the maximum quantities. Overloading can block the mechanism. Limit the amount of food so that air can circulate freely. Is there residue or dirt? Clean the drawer and its grooves with warm water and soap (using a non-abrasive sponge). Residues can prevent proper insertion. Is the removable grid properly placed? Check that the grid integrated into the drawer is correctly positioned and does not protrude. Does the drawer adjustment change after each use? Over time, the guides may loosen slightly. This may require more precise insertion. If after these checks the drawer remains stuck or the device still does not start, and if the drawer does not show any visible cracks, the problem may be internal (defective safety sensor or damaged interlock mechanism). In this case, contact MOULINEX customer service with the reference EZ855D and your proof of purchase.

Q: What does error code E3 mean on my Moulinex EZ855D fryer?

The error code E3 on your Moulinex EZ855D fryer indicates overheating or a blockage of the temperature sensor . The device has automatically shut down for safety to prevent damage. Troubleshooting procedure: Immediately turn off and unplug the fryer from the wall outlet. Wait at least 30 minutes before restarting it, to allow it to cool down completely. Ensure that the fryer has a minimum of 15 cm of free space around it for proper air circulation (top, sides, back). Do not place it in a corner or under an element. Open the removable cooking drawer and thoroughly clean any food residues and accumulated grease, especially around the removable grid. Check that the removable grid is properly inserted and does not block the passage of hot air. Reconnect the device and test a cooking cycle without food. Important: If the E3 code reappears regularly after these checks, the temperature sensor may be faulty. Contact Moulinex support directly for professional diagnosis or sensor replacement. Do not use the device while the error persists.

Q: How do I start my Easy Fry XXL EZ9428 fryer?

Here’s how to start your Easy Fry XXL fryer: Startup Steps: Press the power button ⏻ - Located on the control panel, this button powers the device on. Check the initial display - Once the device is on, the screen automatically displays the “Fries” mode for basket 1, while basket 2 shows “OFF”. Activate a basket - Press the “1” or “2” button to activate the basket you wish to use. You can deactivate a basket by pressing the same button again. Select the cooking mode - Choose a predefined mode (Fries, Chicken, Vegetables, Fish, Dessert, Dehydration) or use the Manual mode to set a custom temperature (40-200°C) and time (0-60 minutes). Start cooking - Press the “Start/Stop” button to begin. The screen will display the remaining cooking time. Tip: Do not add oil or liquid to the baskets - this fryer works by circulating hot air, without oil.

Q: Does the Minifrito AF220010 fryer have a light indicator to signal that the oil is hot?

According to the Minifrito AF220010 manual, there is no light indicator to show that the oil has reached the desired temperature. The device is equipped with a adjustable thermostat that you turn to select the desired temperature before starting (recommended limit: 170°C for potatoes). However, the manual does not mention any signaling system (light indicator, sound signal, or other visual indicator) to alert you of the preheating. To know when the oil is ready, you will need to rely on the recommended cooking times in the manual for each type of food . It is up to you to estimate the preheating time after setting the thermostat.

Q: How to use the Minifrito AF220010 fryer?

The Minifrito AF220010 is a hot air fryer with a capacity of 1.2 kg and 1200 W of power. Here are the essential steps to use it: Initial preparation Remove all packaging and heat accumulators Clean the removable basket and drip tray (dishwasher safe) Ensure the appliance is positioned on a stable, flat surface, away from moisture sources Usage Turn on the appliance and set the adjustable thermostat according to your needs (maximum 170°C recommended for potatoes) Allow to preheat for a few minutes Fill the basket without exceeding the 1.2 kg capacity - do not overload Insert the basket and close the lid Cooking is done with little or no oil (a major advantage of this type of fryer) Safety and maintenance Do not touch hot surfaces during and just after cooking The appliance has an overheating protection with automatic shut-off Wait for the appliance to cool completely before cleaning Never immerse the electrical body in water (clean only with a damp cloth) For specific cooking times and detailed recipes, refer to the 11 FAQs and the complete manual available on this page.

Q: How do I set the temperature and cooking time on my Easy Fry XXL fryer?

Your Moulinex Easy Fry XXL EZ9428 features an intuitive touchscreen to easily control the temperature and cooking time. The controls are simple, and the interface displays the remaining time in real-time during cooking. To set the temperature: Press the + and - buttons displayed on the touchscreen to adjust the thermostat. The temperature range is adjustable from 40 to 200°C . The pre-set modes (fries, chicken, vegetables, fish, desserts, dehydration) automatically use optimal temperatures between 140 and 200°C depending on the food. For example, fries and chicken typically use 180 to 200°C. To set the cooking time: Use the + and - buttons on the screen to adjust the time as well. The timer is adjustable from 0 to 60 minutes . The screen constantly displays the remaining time during cooking, and the device emits a sound signal when cooking is complete. If the food is not ready, you can add a few extra minutes by removing the drawer and adjusting the timer. Complete procedure in manual mode: First, press the power button to turn on the device. The pre-set modes are displayed by default on the touchscreen. If you want a fully customized cooking experience, select the manual mode available on the screen. Then set the temperature using the + and - buttons, followed by the cooking duration in the same way. Once your settings are confirmed, press the start button to begin cooking. The device also has a pause function if you need to access your food while it is cooking. Practical tip: For optimal results, refer to the cooking chart provided in your manual for recommended times based on the food. To reheat food, simply set the temperature to 160°C for a maximum of 10 minutes. You can always adjust the time based on the amount of food in the drawer.

Question 1

How to set the manual program on the MOULINEX EZ245B fryer?

Accepted Answer

To set the manual program on your MOULINEX EZ245B fryer, follow these steps:

Plug in the appliance and place the food in the basket
Reinsert the basket into the fryer
Press the menu button to display the cooking options
Select the manual mode (instead of an automatic mode like Fries, Steak, or Roast Chicken)
Adjust the cooking time from 0 to 60 minutes using the +/- buttons
Adjust the temperature from 70 to 200 °C using the touchscreen controls
Press the Start/Stop button to begin cooking

During cooking, you can change the time and temperature at any time. If you wish to stir the food halfway through cooking, remove the basket by the handle, shake gently, and reinsert it - the appliance will automatically resume.

Question 2

Where can I find the troubleshooting section for the MOULINEX EZ855D fryer?

Accepted Answer

Here is the complete troubleshooting section for your MOULINEX EZ855D fryer:

Device does not turn on (no noise or light)

Check the wall outlet and power cord
Ensure that the voltage corresponds to 220-240 V ~ 50/60 Hz
Insert the cooking drawer firmly until it clicks (mandatory safety system)
Press and hold the Start/Pause button for at least 2 seconds
If the device has been unplugged, wait 5-10 minutes before turning it back on (thermal protection)

Drawer is not working

Check that the drawer is fully inserted until it clicks
Empty the device (overloading blocks the mechanism)
Clean the grooves of the drawer and the body of the device
Check the correct positioning of the removable grid
If the problem persists, contact MOULINEX service

Error code E3

This code indicates overheating or a blockage of the temperature sensor. Proceed as follows:

Turn off and unplug the device immediately
Let it cool down for at least 30 minutes
Check the ventilation around the device (minimum 15 cm of space)
Empty any accumulated food residues
If the error reappears, contact MOULINEX support

Question 3

Why doesn't my MOULINEX EZ855D fryer turn on (no noise, no light)?

Accepted Answer

Here are the checks to perform:

Check the power supply: Make sure the wall outlet is working. Test it with another device (lamp, charger). Check that the voltage matches the 220-240 V ~ 50/60 Hz indicated on the device.
Check the power cord: Inspect the cord for any visible cuts or damage. Try another outlet.
Insert the drawer correctly: The EZ855D fryer has a safety system: it only operates if the cooking drawer is properly inserted all the way into the device. Remove and then reinsert the drawer firmly until you hear a click.
Check the start button: Hold the Start/Pause button for at least 2 seconds. The device should then emit a sound signal and the display should light up.
Wait after unplugging: If the device has been used recently, wait 5-10 minutes before trying again. A thermal protection system may temporarily keep it locked.
Check the drawer safety: Clean the grooves of the drawer and those of the device body to remove any dust or debris that would prevent proper contact.

If after these checks the device remains inert (still no noise or light), it is likely that there is an internal electrical fault requiring repair or replacement.

Question 4

My MOULINEX EZ855D fryer drawer is not working anymore, what should I do?

Accepted Answer

If your cooking drawer is not working on your MOULINEX EZ855D fryer, here are the points to check:

Checks to make:

Is the drawer properly inserted? Make sure that the cooking drawer (removable basket) is fully pushed into the device until it clicks. Incorrect positioning prevents the device from functioning.
Is the drawer overfilled? The manual specifies never to exceed the maximum quantities. Overloading can block the mechanism. Limit the amount of food so that air can circulate freely.
Is there residue or dirt? Clean the drawer and its grooves with warm water and soap (using a non-abrasive sponge). Residues can prevent proper insertion.
Is the removable grid properly placed? Check that the grid integrated into the drawer is correctly positioned and does not protrude.
Does the drawer adjustment change after each use? Over time, the guides may loosen slightly. This may require more precise insertion.

If after these checks the drawer remains stuck or the device still does not start, and if the drawer does not show any visible cracks, the problem may be internal (defective safety sensor or damaged interlock mechanism). In this case, contact MOULINEX customer service with the reference EZ855D and your proof of purchase.

Question 5

Does the power button blink when the fryer is off?

Accepted Answer

No, the power button of the Easy Fry XXL EZ942B fryer should not blink continuously when the device is off.

The digital touch screen simply displays "OFF" when the fryer is in standby mode. The power button does not show continuous blinking in this state.

However, a blinking may occur during cooking: for example, in Fry mode, an icon blinks halfway through cooking to indicate that it's time to shake the fries for even cooking. This is a normal signal from the device to optimize your result.

If you observe abnormal or continuous blinking even when the device is off, check:

That the device is properly plugged in and powered
That the screen displays "OFF"
The condition of the baskets (properly inserted and locked)

Question 6

What does error code E3 mean on my Moulinex EZ855D fryer?

Accepted Answer

The error code E3 on your Moulinex EZ855D fryer indicates overheating or a blockage of the temperature sensor. The device has automatically shut down for safety to prevent damage.

Troubleshooting procedure:

Immediately turn off and unplug the fryer from the wall outlet.
Wait at least 30 minutes before restarting it, to allow it to cool down completely.
Ensure that the fryer has a minimum of 15 cm of free space around it for proper air circulation (top, sides, back). Do not place it in a corner or under an element.
Open the removable cooking drawer and thoroughly clean any food residues and accumulated grease, especially around the removable grid.
Check that the removable grid is properly inserted and does not block the passage of hot air.
Reconnect the device and test a cooking cycle without food.

Important: If the E3 code reappears regularly after these checks, the temperature sensor may be faulty. Contact Moulinex support directly for professional diagnosis or sensor replacement. Do not use the device while the error persists.

Question 7

How do I start my Easy Fry XXL EZ9428 fryer?

Accepted Answer

Here’s how to start your Easy Fry XXL fryer:

Startup Steps:

Press the power button ⏻ - Located on the control panel, this button powers the device on.
Check the initial display - Once the device is on, the screen automatically displays the “Fries” mode for basket 1, while basket 2 shows “OFF”.
Activate a basket - Press the “1” or “2” button to activate the basket you wish to use. You can deactivate a basket by pressing the same button again.
Select the cooking mode - Choose a predefined mode (Fries, Chicken, Vegetables, Fish, Dessert, Dehydration) or use the Manual mode to set a custom temperature (40-200°C) and time (0-60 minutes).
Start cooking - Press the “Start/Stop” button to begin. The screen will display the remaining cooking time.

Tip: Do not add oil or liquid to the baskets - this fryer works by circulating hot air, without oil.

Question 8

Does the Minifrito AF220010 fryer have a light indicator to signal that the oil is hot?

Accepted Answer

According to the Minifrito AF220010 manual, there is no light indicator to show that the oil has reached the desired temperature.

The device is equipped with a adjustable thermostat that you turn to select the desired temperature before starting (recommended limit: 170°C for potatoes). However, the manual does not mention any signaling system (light indicator, sound signal, or other visual indicator) to alert you of the preheating.

To know when the oil is ready, you will need to rely on the recommended cooking times in the manual for each type of food. It is up to you to estimate the preheating time after setting the thermostat.

Question 9

How to use the Minifrito AF220010 fryer?

Accepted Answer

The Minifrito AF220010 is a hot air fryer with a capacity of 1.2 kg and 1200 W of power. Here are the essential steps to use it:

Initial preparation

Remove all packaging and heat accumulators
Clean the removable basket and drip tray (dishwasher safe)
Ensure the appliance is positioned on a stable, flat surface, away from moisture sources

Usage

Turn on the appliance and set the adjustable thermostat according to your needs (maximum 170°C recommended for potatoes)
Allow to preheat for a few minutes
Fill the basket without exceeding the 1.2 kg capacity - do not overload
Insert the basket and close the lid
Cooking is done with little or no oil (a major advantage of this type of fryer)

Safety and maintenance

Do not touch hot surfaces during and just after cooking
The appliance has an overheating protection with automatic shut-off
Wait for the appliance to cool completely before cleaning
Never immerse the electrical body in water (clean only with a damp cloth)

For specific cooking times and detailed recipes, refer to the 11 FAQs and the complete manual available on this page.

Question 10

How do I set the temperature and cooking time on my Easy Fry XXL fryer?

Accepted Answer

Your Moulinex Easy Fry XXL EZ9428 features an intuitive touchscreen to easily control the temperature and cooking time. The controls are simple, and the interface displays the remaining time in real-time during cooking.

To set the temperature: Press the + and - buttons displayed on the touchscreen to adjust the thermostat. The temperature range is adjustable from 40 to 200°C. The pre-set modes (fries, chicken, vegetables, fish, desserts, dehydration) automatically use optimal temperatures between 140 and 200°C depending on the food. For example, fries and chicken typically use 180 to 200°C.

To set the cooking time: Use the + and - buttons on the screen to adjust the time as well. The timer is adjustable from 0 to 60 minutes. The screen constantly displays the remaining time during cooking, and the device emits a sound signal when cooking is complete. If the food is not ready, you can add a few extra minutes by removing the drawer and adjusting the timer.

Complete procedure in manual mode: First, press the power button to turn on the device. The pre-set modes are displayed by default on the touchscreen. If you want a fully customized cooking experience, select the manual mode available on the screen. Then set the temperature using the + and - buttons, followed by the cooking duration in the same way. Once your settings are confirmed, press the start button to begin cooking. The device also has a pause function if you need to access your food while it is cooking.

Practical tip: For optimal results, refer to the cooking chart provided in your manual for recommended times based on the food. To reheat food, simply set the temperature to 160°C for a maximum of 10 minutes. You can always adjust the time based on the amount of food in the drawer.

User manual MOULINEX Deep fryer : user manuals and guides in PDF

Models MOULINEX Deep fryer most viewed

Other categories MOULINEX

Recent questions about Deep fryer MOULINEX