DC213 - Drill DEWALT - Free user manual and instructions

Brand	DeWalt
Model	DC213
Product type	Cordless electro-pneumatic hammer (rotary hammer)
Battery voltage	18 V
No-load speed	0 – 1100 min⁻¹
Speed under load	0 – 800 min⁻¹
Impact energy	2.1 J
Drilling capacity (steel)	13 mm
Drilling capacity (wood)	26 mm
Drilling capacity (concrete)	20 mm
Tool holder	SDS Plus
Collar diameter	54 mm
Weight (without battery)	3.1 kg
Compatible battery types	NiCd, NiMH, Li-Ion (18 V)
Compatible chargers	DE9116, DE9130, DE9135
Operating modes	Drilling, hammer drilling, light chiseling
Variable speed trigger	Yes, with progressive switch
Reversible rotation direction	Yes, left/right selector
Safety	Double insulation, rotor brake, active vibration control
Included accessories (K model)	Side handle, depth stop, 2 batteries, charger, transport case
Maintenance	Dry air cleaning, no greasing required
Warranty	1 year (with conditions)

Frequently Asked Questions - DC213 DEWALT

How to change the operating mode on the DC213?

Press the lock button (4) and turn the mode switch (3) to the desired symbol: drilling, hammer drilling or chiseling. Release the button to lock.

What battery types can I use with the DC213?

The DC213 works with DeWalt 18 V batteries of types NiCd, NiMH or Li-Ion (models DE9095, DE9098, DE9503, DE9180). Use only batteries recommended by DeWalt.

How to install the side handle?

Loosen the side handle, slide the collar onto the collar behind the chuck, orient the handle to the left (right-handed) or right (left-handed), then tighten firmly.

How to adjust the drilling depth?

Insert the depth stop into the eyelet of the side handle, loosen the handle, adjust the depth, then retighten the handle.

How to clean the DC213 rotary hammer?

Remove the battery, blow dust from ventilation slots with dry air. Wear goggles and a mask. Do not use solvents or water.

What to do if the battery does not charge?

Check that the charger is plugged in and the battery is correctly inserted. If the red light flashes quickly, the battery is too hot or too cold. If the light is steady, charging is complete. In case of malfunction, replace the battery.

Can I use standard drill bits with the DC213?

Yes, via an SDS Plus adapter with a cylindrical shank chuck (available optionally). Do not use a standard chuck in hammer mode.

How to change the rotation direction?

Push the left/right rotation selector (2) to the left for right rotation (RH) or to the right for left rotation (LH). Wait for the motor to stop completely before changing.

What is the warranty of the DC213?

DeWalt offers a one-year warranty on material and workmanship defects, including labor (excluding accessories). Proof of purchase is required. There is also a 30-day satisfaction guarantee.

How to store the rotary hammer and its batteries?

Store the tool in a cool, dry place, away from sunlight. Li-Ion batteries should be fully charged before storage. Remove the battery from the tool and place the protective cover on the contacts.

USER MANUAL DC213 DEWALT

You have chosen a DEWALT tool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users.

Technical Data

	DC212		DC213
Voltage	V12:		18
Type 2.2
No load speed min	0	1,100	0	1,100
Load speed min-	0-800		0-800
Impact energy	J		2.1	2.1
Maximum drilling range in steel/wood/concrete	mm		13/26/20	13/26/20
Tool holder			SDS Plus®	SDS Plus®
Collar diameter	mm		54	54
Wght kg	3.1		3.1
LVA (sound pressure) dB(A)			85	87
KVA (sound pressure uncertainty) dB(A)			3	3
LVA (sound power) dB(A)			96	97
KVA (sound power uncertainty) dB(A)			3.1	2.9

Vibration total values (Inx vector sum) determined according to EN 60745:

Vibration emission value an
Drilling into concrete
a1HD m/s2	8	8
Uncertainty K	m/s2	1.5	1.5
Vibration emission value an
Chiselling
a1Chog	m/s2	-	6.5
Uncertainty K	m/s2	-	1.5
Vibration emission value an
Drilling into metal
a1D	m/s2	<2.5	<2.5
Uncertainty K	m/s2	1.5	1.5
Vibration emission value an
Screwdriving
an	m/s2	<2.5	<2.5
Uncertainty K	m/s2	1.5	1.5

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.

WARNING: The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period.

An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.

Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns.

Battery pack		DE9095	DE9098	DE9503	DE9180
Battery type		NCoD	NCoD	NMH	L-ion
Voltage	VDC	18	18	18	18
Capacity	Ah	2.0	2.4	2.6	2.0
Weight	kg	1.0	1.0	1.0	0.68

Charger		DE9116	DE9130	DE9135
Battery type		NiCd/NiMH	NiCd/NiMH	NiCd/NiMH/Lion
Mains voltage	Vcc	230	230	230
Approx. charging time	min	60(2.0 Ah battery packs)	30(2.0 Ah battery packs)	40(2.0 Ah battery packs)
Weight	kg	0.4	0.42	0.52

Fuses:
Europe	230 V tools	10 Amperes, mains
U.K. & Ireland	230 V tools	3 Amperes, in plugs

ENGLISH

Definitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potential hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

NOTICE: indicates a practice not related to personal injury which, if not avoided, may result in property damage.

Denotes risk of electric shock.

EC-Declaration of Conformity

MACHINERY DIRECTIVE

DC212, DC213

DEWALT declares that these products described under "technical data" are designed in compliance with:

98/37/EC (until Dec. 28, 2009), 2006/42/EC (from Dec. 29, 2009), EN 60745-1, EN 60745-2-6.

These products also comply with Directive 2004/108/EC. For more information, please contact DEWALT at the following address or refer to the back of the manual.

The undersigned is responsible for compilation of the technical file and makes this declaration on behalf of DEWALT.

Horst Grossmann

Vice President Engineering and Product Development

D-65510, Idstein, Germany

05.08.2009

WARNING: To reduce the risk of injury, read the instruction manual.

General Power Tool SafetyWarnings

WARNING! Read all safety warnings and instructions Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNING AND INSTRUCTIONS FOR FUTURE REFERENCE

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
i) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in accordance with these instructions taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
b) Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

6) SERVICE

a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

ENGLISH

Additional Safety Instructions for Rotary Hammers

• Wear ear protectors. Exposure to noise can cause hearing loss.
• Use auxiliary handles supplied with the tool. Loss of control can cause personal injury.
• Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator.
• Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.
• Wear safety goggles or other eye protection. Hammering operations cause chips to fly. Flying particles can cause permanent eye damage. Wear a dust mask or respirator for applications that generate dust. Ear protection may be required for most applications.
• Keep a firm grip on the tool at all times. Do not attempt to operate this tool without holding it with both hands. It is recommended that the side handle be used at all times. Operating this tool with one hand will result in loss of control. Breaking through or encountering hard materials such as re-bar may be hazardous as well. Tighten the side handle securely before use.
• Do not operate this tool for long periods of time. Vibration caused by hammer action may be harmful to your hands and arms. Use gloves to provide extra cushion and limit exposure by taking frequent rest periods.
• Do not recondition bits yourself. Chisel reconditioning should be done by an authorized specialist. Improperly reconditioned chisels could cause injury.
• Wear gloves when operating tool or changing bits. Accessible metal parts on the tool and bits may get extremely hot during operation. Small bits of broken material may damage bare hands.
• Never lay the tool down until the bit has come to a complete stop. Moving bits could cause injury.

• Do not strike jammed bits with a hammer to dislodge them. Fragments of metal or material chips could dislodge and cause injury.

• Slightly worn chisels can be resharpened by grinding.

• Keep the power cord away from the rotating bit. Do not wrap the cord around any part of your body. An electric cord wrapped around a spinning bit may cause personal injury and loss of control.

Residual Risks

The following risks are inherent to the use of rotary hammers:

Injuries caused by touching the rotating parts or hot parts of the tool

In spite of the application of the relevant safety regulations and the implementation of safety devices, certain residual risks cannot be avoided. These are:

Impairment of hearing .
- Risk of squeezing fingers when changing the accessory.
Health hazards caused by breathing dust developed when working in concrete and/or masonry.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual before use.

Wear ear protection.

Wear eye protection.

DATE CODE POSITION

The Date Code, which also includes the year of manufacture, is printed into the housing surface that forms the mounting joint between tool and battery.

Example:

2009 XX XX

Year of Manufacture

Important Safety Instructions for All Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instrc tions for the DE9116/DE9130/DE9135 battery chargers.

Before using charger, read all instructions and cautionary markings on charger, battery pack, and product using battery pack.

DANGER: Electrocution hazard. 230 volts are present at charging terminals. Do not probe with conductive objects. Electric shock or electrocution may result.

WARNING: Shock hazard. Do not allow any liquid to get inside charger. Electric shock may result.

CAUTION: Burn hazard. To reduce the risk of injury, charge only DEWALT rechargeable batteries. Other types of batteries may burst causing personal injury and damage.

CAUTION: Under certain conditions, with the charger plugged in to the power supply, the exposed charging contacts inside the charger can be shorted by foreign material. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean.

DO NOT attempt to charge the battery pack with any chargers other than the ones in this manual. The charger and battery pack are specifically designed to work together.
- These chargers are not intended for any uses other than charging DEWALT rechargeable batteries. Any other uses may result in risk of fire, electric shock or electrocution.
- Do not expose charger to rain or snow.
- Pull by plug rather than cord when disconnecting charger. This will reduce risk of damage to electric plug and cord.
Make sure that cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.
- Do not use an extension cord unless it is absolutely necessary. Use of improper extension cord could result in risk of fire, electric shock, or electrocution.
- Do not place any object on top of charger or place the charger on a soft surface that might block the ventilation slots and result

in excessive internal heat. Place the charger in a position away from any heat source. The charger is ventilated through slots in the top and the bottom of the housing.

• Do not operate charger with damaged cord or plug - have them replaced immediately.
• Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way. Take it to an authorized service center.
• Do not disassemble charger; take it to an authorized service center when service or repair is required. Incorrect reassembly may result in a risk of electric shock, electrocution or fire.
• Disconnect the charger from the outlet before attempting any cleaning. This will reduce the risk of electric shock. Removing the battery pack will not reduce this risk.
  NEVER attempt to connect 2 chargers together.
• The charger is designed to operate on standard 230V household electrical power. Do not attempt to use it on any other voltage. This does not apply to the vehicular charger.

SAVE THESE INSTRUCTIONS

Chargers

Your DE9116/DE9130 charger accepts DEWALT NiCd and NiMH battery packs ranging from 7.2 V to 18 V.

The DE9135 charger accepts 7.2 - 18 V NiCd, NiMH or Li-Ion batteries.

These chargers require no adjustment and are designed to be as easy as possible to operate.

Charging Procedure (fi g. A, B)

DANGER:Electrocution hazard. 230 volts present at charging terminals. Do not probe with conductive objects. Danger of electric shock or electrocution.

1. Plug the charger (12) into an appropriate outlet before inserting battery pack.
2. Insert the battery pack into the charger. The red (charging) light will blink continuously indicating that the charging process has started.
3. The completion of charge will be indicated by the red light remaining ON continuously. The pack is fully charged and may be used at this time or left in the charger.

ENGLISH

NOTE: To ensure maximum performance and life of NiCd, NiMH and Li-Ion batteries, charge the battery for a minimum of 10 hours before first use.

Charging Process

Refer the table below for the state of charge of the battery pack.

State of charge

charging

charged

hol/cold pack delay

replace battery pack

problem

1

··

Automatic Refresh

The automatic refresh mode will equalise or balance the individual cells in the battery pack at its peak capacity. Battery packs should be refreshed weekly or whenever the pack no longer delivers the same amount of work.

To refresh your battery pack, place the battery in the charger as usual. Leave the battery pack for at least 10 hours in the charger.

Hot/Cold Pack Delay

When the charger detects a battery that is too hot or too cold, it automatically starts a Hot/Cold Pack Delay, suspending charging until the battery has reached an appropriate temperature. The charger then automatically switches to the pack charging mode. This feature ensures maximum battery life.

LI-ION BATTERY PACKS ONLY

Li-Ion batteries are designed with an Electronic Protection System that will protect the battery against overloading, overheating or deep discharge.

The tool will automatically turn off if the Electronic Protection System engages. If this occurs, place the Li-ion battery on the charger until it is fully charged.

Important Safety Instructions for All Battery Packs

When ordering replacement battery packs, be sure to include catalog number and voltage.

The battery pack is not fully charged out of the carton. Before using the battery pack and charger, read the safety instructions below. Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Inserting or removing the battery from the charger may ignite the dust or fumes.

• Charge the battery packs only in D E WALT chargers.
  DO NOT splash or immerse in water or other liquids.
• Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 40^ (such as outside sheds or metal buildings in summer).

DANGER: Never attempt to open the battery pack for any reason. If battery pack case is cracked or damaged, do not insert into charger. Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer, stepped on). Electric shock or electrocution may result. Damaged battery packs should be returned to service center for recycling.

CAV TIC

ON: When not in use, place

tool on its side on a stable surface where it will not cause a tripping or falling hazard. Some tools with large battery packs will stand upright on the battery pack but may be easily knocked over.

SPECIFIC SAFETY INSTRUCTIONS FOR NICKEL CADMIUM (NiCd) OR NICKEL METAL HYDRIDE (NiMH)

• Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can explode in a fire.
• A small leakage of liquid from the battery pack cells may occur under extreme usage or temperature conditions. This does not indicate a failure.

However, if the outer seal is broken:
a. and the battery liquid gets on your skin, immediately wash with soap and water for several minutes.
b. and the battery liquid gets into your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention. (Medical note: The liquid is 25 - 35% solution of potassium hydroxide.)

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li Ion)

• Do not incinerate the battery pack even if it is severely damaged or is completely worn

out. The battery pack can explode in a fire. Toxic fumes and materials are created when lithium ion battery packs are burned.

• If battery contents come into contact with the skin, immediately wash area with mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts.
• Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persist, seek medical attention.

WARNING: Bum hazard. Battery liquid may be flammable if exposed to spark or flame.

Battery Cap (fi g. B)

A protective battery cap (14) is supplied to cover the contacts of a detached battery pack. Without the protective cap in place, loose metal objects could short circuit the contacts, causing a fire hazard and damaging the battery pack.

1. Take off the protective battery cap before placing the battery pack in the charger or tool.
2. Place the protective cap over the contacts immediately after removing the battery pack from the charger or tool.

WARNING: Make sure the protective battery cap is in place before storing or carrying a detached battery pack.

Battery Pack (fi g. A)

BATTERY TYPE

The DC212 and DC213 operate on 18 volt battery packs.

Storage Recommendations

1. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold. For optimum battery performance and life, store battery packs at room temperature when not in use.
   NOTE: Li-ion battery packs should be fully charged when stored.
2. Long storage will not harm the battery pack or charger. Under proper conditions, they can be stored for up to 5 years.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual, the labels on the charger and the battery pack show the following pictographs:

Read instruction manual before use.

Battery charging

Battery charged

Battery defective

Hot/cold pack delay

Do not probe with conductive objects.

Do not charge damaged battery packs

Use only with DEWALT battery packs, others may burst, causing personal injury and damage.

Do not expose to water.

Have defective cords replaced immediately.

Charge only between 4^ and 40^ .

Discard the battery pack with due care for the environment.

Do not incinerate the battery pack NiMH, NiCd+ and Li-Ion.

NIMH Charges NiMH and NiCd NiCd battery packs.

Li Ion Charges Li-Ion battery packs.

See technical data for charging time.

ENGLISH

Package Contents

The package contains:

1 Cordless rotary hammerdrill
1 Side handle
1 Depth adjustment rod
1 Charger (K-models only)
2 Battery packs (K-models only)
1 Kitbox (K-models only)
1 Instruction manual
1 Exploded drawing
- Check for damage to the tool, parts or accessories which may have occurred during transport.
Take the time to thoroughly read and understand this manual prior to operation.

Description (fig. A)

WARNING: Never modify the power tool or any part of it. Damage or personal injury could result.

INTENDED USE

Your cordless rotary hammerdrill DC212 has been designed for professional drilling, hammerdrilling and screwdriving applications.

Your cordless rotary hammerdrill DC213 has been designed for professional drilling, hammerdrilling and screwdriving applications as well as for light chipping.

DO NOT use under humid conditions or in presence of flammable liquids or gases.

These hammerdrills are professional power tools.

DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool.

1 Variable speed switch
2 Forward/reverse slider
3 Mode selector
4 Safety lock
5 Tool holder
6 Locking collar
7 Dust cover
8 Depth adjustment rod
9 Side handle
10 Battery pack
11 Release buttons
12 Charger
13 Charging indicator (red)

Overload Clutch

In case of jamming of a drill bit, the drive to the drill spindle is interrupted. Because of the resulting forces, always hold the tool with both hands and take a firm stance.

Brake Mechanism

When the variable speed switch is released, the spindle will stop rotating instantly.

Active Vibration Control

The active vibration control neutralises rebound vibration from the hammer mechanism. Lowering hand and arm vibration, it allows more comfortable use for longer periods of time and extends the life of the unit.

In operation, a spring loaded mechanism counterbalances the vibration forces. This can be sensed by the cushioning effect when pressure is applied to the tool. Make sure the spring is engaged but not too firmly. The mechanism should be allowed to 'fl oat'.

Electrical Safety

The electric motor has been designed for one voltage only. Always check that the battery pack voltage corresponds to the voltage on the rating plate. Also make sure that the voltage of your charger corresponds to that of your mains.

Your DeWALT charger is double insulated in accordance with EN 60335; therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by a specially prepared cord available through the DEWALT service organization.

Mains Plug Replacement (U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.

G: No connection is to be made to the earth terminal.

Follow the fitting instructions supplied with good quality plugs. Recommended fuse: 3 A.

Using an Extension Cable

An extension cord should not be used unless absolutely necessary. Use an approved extension

cable suitable for the power input of your charger (see technical data). The minimum conductor size is 1mm^2 ; the maximum length is 30m .

When using a cable reel, always unwind the cable completely.

ASSEMBLY AND ADJUSTMENT

WARNING:

• Prior to assembly and adjustment, always remove the battery pack.

Always switch off the tool before inserting or removing the battery pack.
Before using the tool, make sure battery pack is properly seated.

#

WARNING: Use only DEWALT battery packs and chargers.

Inserting and Removing the Battery Pack (fi g. A, B)

• Insert the battery pack into the grip until it clicks in place.
  To remove the battery pack, press the two release buttons (11) simultaneously and pull the pack out of the grip.

Selecting the Operating Mode (fi g. C1, C2)

DC212 (FIG.C1)

The tool can be used in the following operating modes:

#

Rotary drilling: for screwdriving and for drilling into steel, wood and plastics

T

Hammerdrilling: for concrete and masonry drilling.

DC213 (FIG.C2)

The tool can be used in the following operating modes:

#

Rotary drilling: for screwdriving and for drilling into steel, wood and plastics

T

Hammerdrilling: for concrete and masonry drilling.

T

Hammering only: for light chipping.

• To select the operating mode, press the safety lock (4) and rotate the mode selector switch (3) until it points to the symbol of the required mode.

• Release the safety lock and check that the mode selector switch is locked in place.

WARNING: Do not select the operating mode when the tool is running.

Inserting and Removing SDS Plus Accessories (fi g. D)

Your rotary hammerdrill uses SDS Plus® accessories (refer to the inset in fig. D for a cross-section of an SDS Plus® bit shank).

Clean and grease the bit shank.
- Insert the bit shank into the tool holder (5).

the Push the bit down and turn it slightly until it fits into the slots.

• Pull on the bit to check if it is properly locked. The hammering function requires the bit to be able to move axially several centimetres when locked in the tool holder.
• To remove a bit pull back the tool holder locking sleeve (5, 6) and pull out the bit.

Fitting the Side Handle (fi g. A)

The side handle (9) can be fitted to suit both RH- and LH-users.

WARNING: Always use the tool with the side handle properly assembled.

• Loosen the side handle.
• For RH-users, slide the side handle clamp over the collar behind the tool holder, handle at the left.
• For LH-users, slide the side handle clamp over the collar behind the tool holder, handle at the right.
• Rotate the side handle to the desired position and tighten the handle.

Setting the Drilling Depth (fi g. E)

• Insert the required drill bit.
• Slacken the side handle (9).
• Fit the depth adjustment rod (8) through the hole in the side handle clamp.
• Adjust the drilling depth as shown.
• Tighten the side handle.

Forward/reverse Slider (fi g. F)

• Push the forward/reverse slider (2) to the LH-side for forward (RH) rotation. See arrows on tool.

ENGLISH

• Push the forward/reverse slider (2) to the RH-side for reverse (LH) rotation.

WARNING: Always wait until the motor has come to a complete standstill before changing the direction of rotation.

Replacing the Dust Cover (fi g. D)

The dust cover (7) prevents dust ingress into the mechanism. Replace a worn dust cover immediately.

Pull back the tool holder locking sleeve (5, 6) and pull the dust cover (7) off.
- Fit the new dust cover.
- Release the tool holder locking sleeve.

OPERATION

Instructions for Use

WARNING:

• Always observe the safety instructions and applicable regulations.

• Be aware of the location of pipework and wiring.
  Apply only a gentle pressure to the tool (approx. 5 kg). Excessive force does not speed up drilling but decreases tool performance and may shorten tool life.
  Do not drill or drive too deep to prevent damage to the dust cover.
  Always hold the tool firmly with hands and ensure a secure stance. Always operate the tool with the side handle properly mounted.

Proper Hand Position (fig. A, G)

VG: To reduce the risk of serious personal injury, ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of

serious personal injury, ALWAYS hold securely in anticipation of a sudden reaction.

Proper hand position requires one hand on the side handle (9), with the other hand on the main handle (16).

Switching On and Off (fi g. A)

• To run the tool, press the variable speed switch (1). The pressure exerted on the variable speed switch determines the tool speed.

• To stop the tool, release the switch.
  To lock the tool in off position, move the forward/reverse slider (2) to the central position.

Hammerdrilling (fi g. A)

• Set the mode selector switch (3) to the "hammerdrilling" position.
• Insert the appropriate drill bit. For best results use high quality carbide-tipped bits.
• Adjust the side handle (9) as required.
  If necessary, set the drilling depth.
  Mark the spot where the hole is to be drilled.
• Place the drill bit on the spot and switch on the tool.

Rotary Drilling (fi g. A)

• Set the mode selector switch (3) to the "rotary drilling" position.
  Depending on your tool, follow either of the following instructions:

Fit a chuck adaptor/chuck assembly (DC212/ DC213). Special SDS Plus® adaptors with threaded sections are available for use with standard 10 or 13 mm chucks to enable straight shank bits to be used.

• Proceed as described for hammerdrilling.

WARNING: Never use standard chucks in the hammerdrilling mode.

Screwdriving (fi g. A)

• Set the mode selector switch (3) to the "rotary drilling" position.
• Select the direction of rotation.
  Depending on your tool, follow either of the following instructions:

Insert the special SDRs#h#s#driving adaptor for use with hexagonal screwdriver bits (DC212/DC213).

• Insert the appropriate screwdriver bit. When driving slotted head screws always use bits with a finder sleeve.
• Gently press the variable speed switch (1) to prevent damage to the screw head. In reverse (LH) rotation the tool speed is automatically reduced for easy screw removal.
• When the screw is flush with the workpiece, release the variable speed switch to prevent the screw head from penetrating into the workpiece.

DC213 - Chipping (fi g. A)

• Set the mode selector switch (3) to the "hammering only" position.
• Insert the appropriate chisel and check if it is properly locked.
• Adjust the side handle (9) as required.
• Switch on the tool and start working

It may be necessary to briefly run the motor after having changed from chiselling to rotary modes in order to align the gears.

WARNING:

• Do not use this tool to mix or pump easily combustible or explosive fluids (benzine, alcohol, etc.).
• Do not mix or stir inflammable liquids labelled accordingly.

MAINTENANCE

Your DEWALT power tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning.

• This machine is not user-serviceable. Take the tool to an authorised DEWALT repair agent after approximately 40 hours of use. If problems occur before this time contact an authorised DEWALT repair agent.
  The charger is not serviceable. There are no serviceable parts inside the charger.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen collecting in and around the air vents. Wear approved eye protection and approved dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals may weaken the materials used in these parts. Use a cloth dampened only with water and mild

soap. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect the charger from the AC outlet before cleaning. Dirt and grease may be removed from the exterior of the charger using a cloth or soft non-metallic brush. Do not use water or any cleaning solutions.

Optional Accessories

WARNING: Since accessories, other than those offered by DEWALT, have not been tested with this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only DEWALT, recommended accessories should be used with this product.

Various types of SDS Plus drill bits and chisels are available as an option.

Accessories and attachments used must be regularly lubricated around the SDS Plus fitment.

Consult your dealer for further information on the appropriate accessories.

Protecting the Environment

Separate collection. This product must not be disposed of with normal household waste.

Should you find one day that your DEWALT product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection.

Separate collection of used products and packaging allows materials to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials.

Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product.

DEWALT provides a facility for the collection and recycling of DEWALT products once they have

ENGLISH

reached the end of their working life. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf.

You can check the location of your nearest authorised repair agent by contacting your local DEWALT office at the address indicated in this manual. Alternatively, a list of authorised DEWALT repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com.

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails to produce sufficient power on jobs which were easily done before. At the end of its technical life, discard it with due care for our environment:

• Run the battery pack down completely, then remove it from the tool.
• Li-Ion, NiCd and NiMH cells are recyclable. Take them to your dealer or a local recycling station. The collected battery packs will be recycled or disposed of properly.

GUARANTEE

DEWALT is confident of the quality of its products and offers an outstanding guarantee for professional users of the product. This guarantee statement is in addition to and in no way prejudices your contractual rights as a professional user or your statutory rights as a private non-professional user. The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area.

30 DAY NO RISK SATISFACTION GUARANTEE

If you are not completely satisfied with the performance of your DEWALT tool, simply return it within 30 days, complete with all original components, as purchased, to the point of purchase, for a full refund or exchange. The product must have been subject to fair wear and tear and proof of purchase must be produced.

- ONE YEAR FREE SERVICE CONTRACT

If you need maintenance or service for your DeWALT tool, in the 12 months following purchase, you are entitled to one service free of charge. It will be undertaken free of charge at an authorised DeWALT repair agent. Proof of purchase must be produced. Includes labour. Excludes accessories and spare parts unless failed under warranty.

- ONE YEAR FULL WARRANTY

If your DEWALT product becomes defective due to faulty materials or workmanship within 12 months from the date of purchase, DEWALT guarantees to replace all defective parts free of charge or - at our discretion - replace the unit free of charge provided that:

The product has not been misused;
The product has been subject to fair wear and tear;
- Repairs have not been attempted by unauthorised persons;
Proof of purchase is produced.
The product is returned complete with all original components

If you wish to make a claim, contact your seller or check the location of your nearest authorised DEWALT repair agent in the DEWALT catalogue or contact your DEWALT office at the address indicated in this manual. A list of authorised DEWALT repair agents and full details of our after-sales service is available on the Internet at: www.2helpU.com

TALADRO PERCUTOR SIN CABLE DC212, DC213

Enhorabuena!

Charges NIMH and NiCd battery packs.

Charge les blocs-piles Li-lon.

L'emballage content:

Embrayage de surcharge

Bloc-piles rechargeable

trilngsutstoovwew word gameten in

Hef gereoschap. Mear as He

her geroedeschap utgeschakeld is of

Wannoc her geoschap waaan

WRRK. LARH NCT BICSKAWGswad

1

Wenchenco.

WAARSCHUWING:Loos 00

WAARSCHUWING! Lees alle

BEWAARALLE WAARSCHUWINGEN EN

INSTRUCTIESOM LATER TE RAADPLEGEM

De term 'eoktrisch garooschap in al

gassen of stor. 2019

CROCR:WVW7WALDOERSTOR

1. Hourly rate on amortized costs will do

1) SIKKERHET PÁ ARBEIDSPLASSEN

Kun hamring for lett hakking.

Vice President Engineering and Product Development

DEWALT, Richard-Klinger-Strase 11, D-65510, Idstein, Saksa

05.08.2009

UPPLADDNINGSBAR BORRHAMMARE DC212, DC213

Vi gratular!

NIKEL KADMIYUM (NiCd) VEYA NIKEL METAL HIDRIT (NiMH) IÇIN ÖZEL GÜVENLIK TALIMATLARI

Doner Delme (sekil A)

TinEKIOPTINs Kpaadagaw a Bldw

a_h m/s² <2,5<2,5 Aβεβαίοιητα K: m/s² 1,5 1,5

MTatapia DE9095 DE9098 DE9503 DE9180

Xpovoc opptionkata TPOOeyyion

6) ΣYNTHPHΣH (ΣEPBΣ)

a)Φoovtioe onwg n ouvtiponou nAekpikou Epyaleoiu npayatottoieiata oTiototoinve yia etokuec atopo, uE tn xpon twv rautoanuv mvo aVtAAakiv. Auto ta eaoaipaiei t thdiiponn ts aospaleic tou nAekpikou Epyaleiou.

PpOoTeoi Kavovc aOqaaIac EIOIKA yia TEPiOTpOPIKcS OUPeC

Φopar TPOOATEUNTIa TA autua.H ekTeaOno ToToPOpu MIOpei va TpOKaAeoi atwAei AOKJc.
Xpnoiotoiie Tc Bonntikcs Aaies cou npexoyvat e to epyaiao. H aWaeia eEyxou mtopei va pokalaeetippoawntiko tpaupanuo.
Na Kpatate ta nEeKpiKa epyaiaea ato nouwvees EtnapieKcpatnatoC orav kEeite epyaoies, kata nOtoies Ta epyaia Kaotnc Evexetai va epouv OE tApn me Kpupcs Kaawdioei nmu To Kaawio Tou epyaieou. H tApn neKtropopopo Oupa Ta Kataotnoe i nEeKtpoPopa Ka tEkeBteJeuva mTaAkk aunata Tou nEeKtpiKoi epyaieou, TPOKAAWVtac nEeKtpoTAnLgia oTo xeiipiotn.
Xpnoiopoioane opikyntpec n ao npaktiko tpoT OIA Tn otepewon me aopaaia kai tvuotnpiŋ tou uto katepyaia avtikeievou oe ia otatepi n ato. To Kpatmaouaviteivou ue to xepi n otepewon Tou 0To oua oac svev evyuaia tn otatepoetaia ka evdexetai va onnyoe ai wlaia eleyxou.
- Popate npoataeunika yuaia n aaaa npootateukia yia ta maia. Oi eyaicc apnpnlatanans exouw as atotelaea m v epavian i ntaevw okaividw. Ta tmaeva ouaantia mbopoov u pokaleou ovmoue