PLLA 12 C3 - LED Lighting PARKSIDE - Free user manual and instructions

Product type	Cordless LED work light (hand lamp)
Brand	Parkside
Model	PLLA 12 C3
Rated voltage	12 V (direct current)
Rated current	Max. 0.41 A
Rated power	5 W
Light source type	10 LEDs of 0.5 W each (not individually replaceable)
Luminous flux	480 lumens
Protection class	III (extra-low voltage)
Ingress protection	IP20
Power supply	Lithium-ion battery from the Parkside X 12 V TEAM range (not included)
Compatible batteries	PAPK 12 A1, PAPK 12 B1, PAPK 12 B2
Compatible chargers	PLGK 12 A1, PLGK 12 A2, PLGK 12 B2
Number of angle positions	8 adjustable positions
Special features	Integrated magnet, belt clip, tripod thread (1/4"), brightness control
Brightness control	Press and hold the switch for 3 seconds to reduce intensity
Intended use	Lighting of dry indoor spaces (garage, cellar, attic) - not for domestic lighting
Maintenance	No maintenance required; clean with a soft, dry cloth
Cleaning	Turn off and remove battery before cleaning; do not use water or harsh chemicals
Storage	Remove battery if storing for extended periods; fully recharge beforehand
Safety	Do not look directly at the beam; do not cover while operating; keep away from magnetic media
Repairability	Light source not replaceable; entire lamp to be replaced at end of life
Warranty	3 years (France and Belgium)
Included accessories	Lamp only; battery and charger sold separately

Frequently Asked Questions - PLLA 12 C3 PARKSIDE

What type of battery does the Parkside PLLA 12 C3 use?

It uses a lithium-ion battery from the Parkside X 12 V TEAM range, compatible models: PAPK 12 A1, PAPK 12 B1, PAPK 12 B2. The battery is not included.

Is the Parkside PLLA 12 C3 waterproof?

No, the ingress protection rating is IP20, meaning it is protected against solid objects larger than 12.5 mm but not against water. Do not use outdoors or in humid environments.

How do I adjust the brightness of the lamp?

Press the on/off switch (6) for about 3 seconds to reduce brightness. Press again for 3 seconds to return to maximum. A short press turns off the lamp.

Can I replace the LEDs of the lamp?

No, the light source is not replaceable. When the LEDs reach the end of their life, the entire lamp must be replaced.

How do I attach the lamp to a metal surface?

Use the integrated magnet (9) to attach it to any magnetic surface. Caution: scratches may appear on the magnetic surface when moving it.

Can the lamp be used on a tripod?

Yes, thanks to the internal 1/4-inch thread (5) located under the lamp, you can screw it onto a standard tripod (not included).

Which chargers are compatible with the battery?

Chargers from the Parkside X 12 V TEAM range: PLGK 12 A1, PLGK 12 A2, PLGK 12 B2. The battery can only be charged indoors.

How do I clean the Parkside PLLA 12 C3 lamp?

Turn off the lamp and remove the battery. Clean with a soft, dry cloth. Never use water, harsh chemicals, or metal objects to avoid short circuits.

What is the luminous power of the lamp?

The luminous flux is 480 lumens, with a power of 5 W (10 LEDs of 0.5 W each).

What to do in case of a defect within 3 years?

Contact the Service-Center (France: 0800 919270, Belgium: 070 270 171) with the receipt and the IAN number 338162_2001. You will receive instructions for a free return.

USER MANUAL PLLA 12 C3 PARKSIDE

Baladeuse LED rechargeable

Cordless LED Work Light

Translation of the original instructions

NL BE

Accu-led-werklamp

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

FR B

Intended purpose.....17

General description.....17

Extent of the delivery .17

Functional description...... 17

Overview 17

Technical data 18

Safety instructions.....18

Symbols and icons 18

Safety notices for battery-powered lamps 19

Use and treatment of this battery-powered tool ......... 19

Operation 21

Inserting/removing the battery. 21

Checking the battery charge level 21

Switching ON and OFF....22

Working instructions…22

Swivelling the battery-powered LED work light.... 22

Magnet. 22

Tripod mount 23

Maintenance 23

Cleaning 23

Storage. 23

Disposal and protection of the environment..... 23

Accessories 24

Guarantee 24

Repair Service. 26

Service-Center 26

Importer 26

Translation of the original EC declaration of conformity 93

Exploded Drawing ...... 99

Introduction

Congratulations on the purchase of your new device. With it, you have chosen a high quality product. During production, this equipment has been checked for quality and subjected to a final inspection. The functionality of your equipment is therefore guaranteed.

The operating instructions constitute part of this product. They contain important information on safety, use and disposal. Before using the product, familiarise yourself with all of the operating and safety instructions.

Use the product only as described and for the applications specified. Keep this manual safely and in the event that the product is passed on, hand over all documents to the third party.

Intended purpose

This vibration-proof battery-powered LED work light is ideal for illuminating dry, poorly lit interiors, for example garages, cellars or loft.

The battery-powered LED work light is not suitable for lighting household rooms.

This battery-powered LED work light is not intended for commercial use.

This battery-powered LED work light is not intended for harsh operating conditions.

The device is part of the Parkside X 12 V TEAM series and can be operated using Parkside X 12 V TEAM series batteries. The batteries may only be charged using chargers from the Parkside X 12 V TEAM series.

General description

The illustrations can be found on the

fold-out page.

Extent of the delivery

Carefully unpack the appliance and check that it is complete.

• Cordless LED Work Light
• Instruction Manual

Dispose of the packaging material correctly.

Battery and charger are not included.

Functional description

Refer to the following descriptions for a functional description of the controls.

Overview

1 Belt clip
2 Battery release button
3 Rechargeable battery
4 LED lamp
5 1/4" inner thread
6 On/off switch

7 Battery charge level indicator
8 Appliance housing
9 Magnet
10 Charger

Technical data

Cordless LED Work Light......PLLA 12 C3

Nominal voltage U.....12 V =
Power......max.0,41A
Rated output P_ .5 W
Number of lamps (LED) 10 × 0.5 ~W
Light output. 480 lm
Protection class... III
Protection category ...... IP20

Attention! An up-to-date list of battery compatibility can be found at: www.lidl.de/akku

This device can only be operated with the following rechargeable batteries:
PAPK 12 A1, PAPK 12 A2,
PAPK 12 B1, PAPK 12 B2.
This type of battery may only be charged with the following chargers:

PLGK 12 A1, PLGK 12 A2, PLGK 12 B2.

Safety instructions Symbols and icons

Symbols on the appliance:

Electrical appliances must not be disposed of with the domestic waste.

Protection class

=Direct voltage

Symbols in the manual

Warning symbols with information on damage and injury prevention.

Hazard symbol with information on the prevention of personal injury caused by electric shock.

Instruction symbols with information on preventing damage

Help symbols with information on improving tool handling.

Alternating voltage

Safety notices for battery-powered lamps

• Do not cover the battery-powered LED work light when in use. The battery-powered LED work light becomes hot during use and can cause fire.

• Do not look into the light beam. Do not aim the light beam at people or animals.

• Do not allow children to use the battery-powered LED work light. They could inadvertently blind other people or themselves.

• Keep the battery-powered LED work light away from magnetically sensitive devices and ma

gnetic data storage media. Due to the magnet, there could be irreversible data loss.

• Check that the battery powered LED work light's mounting is solid. There is a risk of injury if the battery-powered LED work light falls down.

• The light source in this lamp is not replaceable; if the light source has reached the end of its life, then the whole lamp must be replaced.

Use and treatment of this battery-powered tool

• Only recharge the battery using chargers recommended by the manufacturer. If a charger that has been designed for a particular type of battery is used to charge other batteries, there is a risk of fire.

• Only use the battery

that is intended in an electric tool. The use of other batteries may create a fire hazard and lead to injury.

• When not in use, keep batteries away from paper clips, coins, keys, nails, screws or other small metal objects that could cause the contacts to be bridged. A short circuit between battery contacts can result in burns or a fire.

• When misused, fluid may leak from the battery. Avoid any contact with it. On accidental contact, wash in running water. If the fluid comes into contact with the eyes, seek medical assistance also. Leaking battery fluid can cause skin irritation or burns.

Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Special safety directions for battery-operated tools

• Ensure that the device is switched off before inserting the battery. Inserting a battery into a power tool that is switched on may result in accidents.

• Recharge the batteries indoors only because the battery charger is designed for indoor use only.

To reduce the electric shock hazard, unplug the battery charger from the mains before

cleaning the charger.

• Do not subject the battery to strong sunlight over long periods and do not leave it on a heater. Heat damages the battery and there is a risk of explosion.
• Allow a hot battery to cool before charging.
• Do not open up the battery and avoid mechanical damage to the battery. Risk of short circuit and fumes may be emitted that irritate the respiratory tract. Ensure fresh air and seek medical assistance.
• Do not use non-rechargeable batteries!
• Do not use any accessories that are not recommended by PARKSIDE. This can result in electric shock or fire.

Observe the safety information and notes on charging

and proper use as shown in the instruction manual for your battery and charger from the Parkside X 12 V TEAM series. A detailed description of the charging process and further information can be found in the separate operating instructions.

Operation

Inserting/removing the battery

1. To insert the battery (3), place it on the guide track and push it back into the appliance. It will audibly snap in.
2. To remove the battery (3) from the appliance, press the release buttons (2) on the battery and pull out the battery.

Checking the battery charge level

The battery's (3) charge level is indicated by the charge state indicator (7).

GBIE

• The LEDs indicate the battery's charge level, when the device is in operation.

red-yellow-green => Battery fully charged red and yellow => Battery half charged red => Battery needs to be charged

Switching ON and OFF

1. To start, press the on/off switch (6). The LED lamp illuminates with maximum brightness.
2. To reduce the brightness, hold down the on/off switch (6) for about 3 seconds. To return to maximum brightness, press the on/off switch (6) again for about 3 seconds.
3. To switch off, briefly press the on/off switch (6).

During breaks in work, the device can be hung from a belt, using the integral belt clip (1).

Working instructions

Do not stare into the battery-powered LED work light when it is switched on

Swivelling the battery-powered LED work light

The LED light (4) can be folded out from the device housing (8) and adjusted to 8 positions.

Magnet

Take care, because sliding the battery-powered LED work light can cause the magnetic surface to become scratched!

Using the magnets (9), you can fix the battery-powered LED work lamp to magnetic surfaces

The LED light (4) can be folded out from the device housing (8) and adjusted to 8 positions. See illustration B.

Tripod mount

Using the 1/4'' inner thread (5) you can screw the battery-powered LED work lamp onto a tripod (not included in this package).

Maintenance

The battery-powered LED work lamp is maintenance-free

Cleaning

Switch off the battery-operated LED light and remove the battery from the device before cleaning.

• Clean the battery-powered LED work lamp with a soft, dry cloth to avoid scratching the cover of the LED lamp.

• Do not use any abrasive cleaning agents or solvents. These could damage the device irreparably.

• Do not use water or metallic aids. There is a risk of a short circuit.

Storage

Before prolonged storage, remove the battery from the device and charge it fully.

Disposal and protection of the environment

Remove the battery from the device and recycle the device and packaging in an environmentally-friendly manner. Instruction on how to dispose of the rechargeable battery can be found in the separate instruction manual.

Machines do not belong with domestic waste.

• Return the unit to a recycling centre. The plastics and metals in the unit can be sorted and appropriately recycled. Ask our Service Centre for details.

• Dispose of batteries in accordance with the local regulations. Take batteries to an old battery collection point where they will be recycled in an environmentally friendly manner.

For information about this, ask your local waste management company or our service centre.

Defective units returned to us will be disposed of for free.

Accessories

Accessories can be obtained at www.grizzly-service.eu

If you have issues ordering, please use the contact form. If you have any other questions, contact the "Service-Center" (see page 26).

Guarantee

Dear Customer,
This device comes with a three-year warranty from the date of purchase.
In case of defects, you have statutory rights against the seller of the product. These statutory rights are not restricted by our guarantee presented below.

Terms of Guarantee

The term of the guarantee be

gins on the date of purchase. Please retain the original receipt. This document is required as proof of purchase. If a material or manufacturing defect occurs within three years of the date of purchase of this product, we will repair or replace - at our choice - the product for you free of charge. This guarantee requires the defective equipment and proof of purchase to be presented within the three-year period with a brief written description of what constitutes the defect and when it occurred. If the defect is covered by our guarantee, you will receive either the repaired product or a new product. No new guarantee period begins on repair or replacement of the product.

Guarantee Period and Statutory Claims for Defects

The guarantee period is not extended by the guarantee service. This also applies for replaced or repaired parts. Any damages and defects already present at the time of purchase must be reported immediately

after unpacking. Repairs arising after expiry of the guarantee period are chargeable.

Guarantee Cover

The equipment has been carefully produced in accordance with strict quality guidelines and conscientiously checked prior to delivery.

The warranty is only valid for material or manufacturing defects. This warranty does not extend to consumable parts exposed to normal wear and tear (e.g. battery capacity). This guarantee shall be invalid if the product has been damaged, used incorrectly or not maintained. Neither does it extend to damage resulting from water, frost, lightning and fire or improper transport. Precise adherence to all of the instructions specified in the operating manual is required for proper use of the product. Intended uses and actions against which the operating manual advises or warns must be categorically avoided.

The product is designed only for private and not commercial

use. The guarantee will be invalidated in case of misuse or improper handling, use of force, or interventions not undertaken by our authorised service branch.

Processing in Case of Guarantee

To ensure efficient handling of your query, please follow the directions below:

• Please have the receipt and item number (IAN 338162_2001) ready as proof of purchase for all enquiries.

• Please find the item number on the rating plate.

• Should functional errors or other defects occur, please initially contact the service department specified below by telephone or by e-mail. You will then receive further information on the processing of your complaint.

• After consultation with our customer service, a product recorded as defective can be sent postage paid to the service address communicated to you, with the proof of purchase (receipt) and

specification of what constitutes the defect and when it occurred. In order to avoid acceptance problems and additional costs, please be sure to use only the address communicated to you. Ensure that the consignment is not sent carriage forward or by bulky goods, express or other special freight. Please send the equipment inc. all accessories supplied at the time of purchase and ensure adequate, safe transport packaging.

Repair Service

For a charge, repairs not covered by the guarantee can be carried out by our service branch, which will be happy to issue a cost estimate for you. We can handle only equipment that has been sent with adequate packaging and postage. Attention: Please send your equipment to our service branch in clean condition and with an indication of the defect. Equipment sent carriage forward or by bulky goods, express or other special freight will not be accepted.

We will dispose of your defective devices free of charge when you send them to us.

Service-Center

GB Service Great Britain

Tel.: [phone]

E-Mail: [e-mail]

IAN 338162_2001

IE Service Ireland

Tel.: [phone]

(0,08 EUR/Min., (peak))

(0,06 EUR/Min.)

(off peak))

E-Mail: [e-mail]

IAN 338162_2001

Importer

Please note that the following address is not a service address. Please initially contact the service centre specified above.

Nominate spanning U....12 V=

Stroom......max. 0,41 A

Nominal vermogen

Pmax. 5 W

Aantal lampen

(LED) 10 × 0.5 ~W

Lichtstroom 480 lm

Translation of the original EC declaration of conformity
We hereby confirm that the Cordless LED Work Light, PLLA 12 C3 series Serial number 202007000001 - 202007010483
conforms with the following applicable relevant version of the EU guidelines:
2014/30/EU • 2014/35/EU • 2009/125/EC • 2011/65/EU*
In order to guarantee consistency, the following harmonised standards as well as national standards and stipulations have been applied:
EN 60598-1:2015/A1:2018 • EN 60598-2-8: 2013 EN 62493:2015 • EN 62471: 2008 • EN 62321-1:2013 EN 55015:2013/A1:2015 • EN 61547:2009
This declaration of conformity (20)** is issued under the sole responsibility of the manufacturer:
Grizzly Tools GmbH & Co. KG Stockstädter Straße 20 63762 Großbostheim, GERMANY, 30.07.2020	Christian Frank (Documentation Representative)

• The object of the declaration described above satisfies the provisions of Directive 2011/65/EU of the European Parliament and the Council of 8 June 2011 on limiting the use of certain harmful substances in electrical and electronic appliances.
  ** The last two digits of the year in which the CE marking was affixed.