GSN36BIEP - Fridge BOSCH - Free user manual and instructions

USER MANUAL GSN36BIEP BOSCH

These repair hints support consumer to repair appliances by himself according to the applicable eco-design regulation (as of 03/2021). They contain information how to exchange defined spare parts including warnings and risks. In case of questions, please contact our customer service. We will only be liable for damages if the repair hints have been followed properly.

1.2 Explanation of symbols

The warning levels consist of a symbol and a signal word. The signal word indicates the severity of the danger. Warning level Meaning Danger Non-observance of the warning message will result in death or serious injuries. Warning Non-observance of the warning message could result in death or serious injuries. Caution Non-observance of the warning message could result in minor injuries. Notice Non-observance of the warning message could result in damage to property. Table1: Danger levels

1.2.2 Hazard symbols

Hazard symbols are symbolic representations which give an indication of the kind of danger. The following hazard symbols are used in this document: Hazard symbol Meaning General warning message Danger from electrical voltage Risk of explosion Danger of cuts Danger of crushing Concerning this document 2021-03-11_9001631451 Copyright by BSH Hausgeräte GmbH Page116of543Hazard symbol Meaning Danger from hot surfaces Danger from strong magnetic field Danger from non-ionizing radiation Table2: Hazard symbols

1.2.3 Structure of the warnings

Warnings in this document have a standardised appearance and a standardised struc- ture. Danger Type and source of danger! Possible consequences of ignoring the danger / warning.

Measures and prohibitions for preventing the danger. The following example shows a warning that warns against electric shock due to live parts. The measure for avoiding the danger is mentioned. Danger Risk of electric shock due to live parts! Death by electrocution

Disconnect appliances from electrical supply at least 60 seconds before starting repairs.

1.2.4 General symbols

The following general symbols are used in this document: Gen. symbol Meaning Identification of a special tip (text and/or graphic) Identification of a simple tip (only text) Identification of a link to a video tutorial Gen. symbol Meaning Identification of required tools Identification of required preconditions Identification of a condition (if ..., then ...) Identification of a result Start Identification of a key or button [00123456] Identification of a material number Status Identification of displayed text / window (in the appliance's display) Table3: General symbols Concerning this document 2021-03-11_9001631451 Copyright by BSH Hausgeräte GmbH Page117of543Safety

2.1 General Safety instructions

2.1.1 All domestic appliances

Risk of electric shock due to live parts! ¡ Errors by repairs involving electrical components can lead to electrical shock! ¡ Disconnect the appliance from the mains for at least 60 seconds before starting work. ¡ After the repair have a safety test according VDE 0701 or country-specific regula- tions performed. Risk of injury from sharp edges! ¡ Wear protective gloves. Risk of crushing during repair, maintenance, troubleshooting and service due to heavy and moving components ¡ Wear protective shoes. ¡ Secure heavy components from falling down. ¡ Do not stick body parts into moving components. Risk to the appliance's safety / function! ¡ Only use original spare parts. Risk of damage to electrostatically sensitive components (ESDs)! ¡ Do not touch the modules, including connections and conductor paths. Safety 2021-03-11_9001631451 Copyright by BSH Hausgeräte GmbH Page118of543Tools and aids Designation Details Images Protection cloth [00342013] 60cm x 50cm Phillips screwdriver PH2 Torx Bit TX20 [00340865] 6,3mm (1/4") Slotted screwdriver Blade 2.4mm x 0.4mm x 60mm, in the kit [00341820] Tools and aids 2021-03-11_9001631451 Copyright by BSH Hausgeräte GmbH Page119of543Repair

4.1 Replacing door gasket

Prerequisite: Door is open.

4.1.1 Removing door gasket

1. Release door gasket from the groove on right and left corner.

2. Pull out door gasket from groove.

Door gasket is removed.

4.1.2 Installing door gasket

Thickness of new door gasket may deviate slightly from thickness of old door gasket. This will not affect closing behavior and long-term function. If your appliance has adjustable hinges or hinge attachments, you can optimize the closing behavior subsequently. Small side holes in door gasket are functional (required for ventilation). These are not production faults. Repair 2021-03-11_9001631451 Copyright by BSH Hausgeräte GmbH Page120of5431. Check groove for gasket for damage.

If groove for gasket is it is damaged. - Contact customer service.

Slight deformation of door gasket is normal and does not affect its function. It is recommended to straighten door gasket before insert- ing it into appliance. Heat door gasket with a hair dryer or hot water and manually reshape it.

4. Push corners of gasket at the top and bottom to the groove.

Repair 2021-03-11_9001631451 Copyright by BSH Hausgeräte GmbH Page121of5435. Press whole gasket step by step into the groove. Door gasket is installed. Repair 2021-03-11_9001631451 Copyright by BSH Hausgeräte GmbH Page122of5434.2 Replacing door handle Required tools: Torx Bit TX20 6,3mm (1/4") [00340865] Slotted screwdriver Blade 10mm x 1.6mm x 200mm Prerequisite: Appliance is disconnected from power supply. Door is open.

1. Remove two screw caps (1).

2. Unscrew two screws (2).

3. Remove door handle (3).

Door handle is removed.

Install in reverse order. Repair 2021-03-11_9001631451 Copyright by BSH Hausgeräte GmbH Page123of5434.3 Replacing easy opening handle Required tools: Phillips screwdriver PH2 Prerequisite: Appliance is disconnected from power supply. Door is open.

1. Remove easy opening handle cover (1).

2. Unscrew two screws (2).

Easy opening handle is removed.

4.3.2 Installing easy opening handle

Easy opening handle mechanism should be properly set before installa- tion. Correct arrangement of push rod (1), toothed quadrants (2) and (3), spring (4) and limit stop (5) for the door left side installation is shown on the graphic. Arrangement of easy opening handle sub-components for door right side installation is described in the document "Installation instruction".

Appliance door removal operation should only be carried out by trained specialists.

To move the appliance, two people are required.

Use only suitable tools and equipment. Caution Sharp edges! Cut injuries

Wear protective gloves. Warning Slipping of tilted appliances! Bone fractures / crush injuries

Secure appliances against slipping. Caution Risk of falling parts due to released screws! Injury because of falling parts.

Secure component from falling down. Notice Risk of falling parts due to released screws! Damage to other parts of the appliance or at customers home e.g. bot- tom.

Secure component from falling down. Prerequisite: Appliance is disconnected from power supply. Appliance interior fittings are removed.

2. 1. Press upper hinge cover on both sides (1).

Door upper hinge is removed.

Appliance door removal operation should only be carried out by trained specialists.

To move the appliance, two people are required.

Use only suitable tools and equipment. Caution Sharp edges! Cut injuries

Wear protective gloves. Warning Slipping of tilted appliances! Bone fractures / crush injuries

Secure appliances against slipping. Caution Risk of falling parts due to released screws! Injury because of falling parts.

Secure component from falling down. Notice Risk of falling parts due to released screws! Damage to other parts of the appliance or at customers home e.g. bot- tom.

Secure component from falling down. Danger Risk of electric shock due to live parts! Danger to life through electric shock in case of improper repair

Electric parts should be repaired by a qualified electricians.

After the repair have a safety test according VDE 0701 or country- specific regulations performed. Danger Risk of electric shock due to live parts! Death by electrocution

Disconnect appliances from electrical supply at least 60 seconds before starting repairs. Prerequisite: Appliance is disconnected from power supply. Appliance interior fittings are removed. Repair 2021-03-11_9001631451 Copyright by BSH Hausgeräte GmbH Page128of5434.5.1 Removing door hinge

1. Place appliance on the back side.

4. Unscrew two screws (4).

5. Remove upper hinge (5).

Door upper hinge is removed.

Appliance door removal operation should only be carried out by trained specialists.

To move the appliance, two people are required.

Use only suitable tools and equipment. Caution Sharp edges! Cut injuries

Wear protective gloves. Warning Slipping of tilted appliances! Bone fractures / crush injuries

Secure appliances against slipping. Caution Risk of falling parts due to released screws! Injury because of falling parts.

Secure component from falling down. Notice Risk of falling parts due to released screws! Damage to other parts of the appliance or at customers home e.g. bot- tom.

Secure component from falling down. Prerequisite: Appliance is disconnected from power supply. Appliance interior fittings are removed. Appliance is placed on the back side. Upper hinge is removed.→Page 128

Pull out shelf. Shelf is removed.

Frozen food container is removed.

1. Pull out shelf frozen food container with ice maker (1).

Ice maker is removed.

Install in reverse order. Repair 2021-03-11_9001631451 Copyright by BSH Hausgeräte GmbH Page135of5434.10 Replacing LED top light Required tools: Slotted screwdriver Blade 2.4mm x 0.4mm x 60mm, in the kit [00341820] Your appliance features a maintenance-free LED light. These lights may be repaired by customer service or authorised techni- cians only! Danger Risk of electric shock due to live parts! Danger to life through electric shock in case of improper repair

Electric parts should be repaired by a qualified electricians.

After the repair have a safety test according VDE 0701 or country- specific regulations performed. Danger Risk of electric shock due to live parts! Death by electrocution

Disconnect appliances from electrical supply at least 60 seconds before starting repairs. Caution Sharp edges! Cut injuries

Wear protective gloves. Prerequisite: Appliance is disconnected from power supply. Door is open. Upper interior fittings are removed.

4.10.1 Removing LED light

1. Move the LED light to the left side.

LED light electrical connection is disconnected.

2. Release LED light hooks.