MN 105 - Foot bath ECG - Free user manual and instructions

USER MANUAL MN 105 ECG

8. Cleaning cosmetic brush with

disks* - with rough grinding head - with ne grinding head - with cleaning brush - with sponge to spread cream (The cosmetic brush set with replaceable disks can be purchased separately under the reference ECG OP 200) HR/BIH

7. Upper respiratory tract

(Upper respiratory tract, head, brain)

SAFETY INSTRUCTIONS Please read carefully and keep for future reference.

Warning: The safety measures and instructions, contained in this

manual, do not include all potential conditions and scenarios. The user must understand that common sense, caution and care are factors that cannot be integrated into aproduct. Therefore, the user is responsible for these factors when using and operating this appliance. We are not liable for any damages caused during shipping, by incorrect use, voltage uctuation or the modication or adjustment of any part of the appliance. To protect against the risk of re or electric shock, basic precautions must be taken while using electrical appliances, including the following:

1. Make sure the voltage in your outlet corresponds to the voltage

provided on the appliance label and that the socket is correctly grounded. The outlet must be installed in accordance with applicable electrical codes according to EN.

2. Do not operate the device if the cord is damaged. All repairs,

including cord replacements, must be carried out at a professional service centre! Do not remove the protective covers from the appliance; there is arisk of electric shock!

3. Never connect or disconnect the supply cable into/from the

electricity socket with your feet immersed in water.

4. Only use the device on axed pad and inside the room; never use

the foot massage device outdoors or in a wet environment and do not touch the power cord or the device with wet hands. Risk of electric shock. Never submerge the foot massage device in water!

5. Pay particular care when using the massage device near children.

6. Do not turn the device on or o by plugging or unplugging the

power cord. First, switch o the massage device with the control ring, then unplug the power cord from the outlet.

7. We recommend not to leave the plugged in massage device

unattended. Disconnect the cord from the electrical outlet prior to any maintenance. Do not remove the power cord from the outletGB

by yanking the cord. Unplug the power cord from the outlet by grasping the plug.

8. Do not allow the power cord to touch hot surfaces or run the cord

9. Never stand in the massage device; always use it in the sitting

10. The device must only be used when lled with water.

11. Do not use the massage device while asleep or if you are groggy or

12. If you do not feel well when using the device or feel any pain,

irritation or nervousness, stop the massage. Do not massage swollen, bloated or otherwise aching feet. Consult with your doctor rst.

13. The device is hot on the surface. People with reduced heat sensitivity

must be careful when using this massage device.

14. Use the massage device strictly in accordance with the instructions

contained in this manual. The manufacturer is not liable for any damage caused by the improper use of this appliance.

15. This appliance can be used by children aged eight and older and

by the physically and mentally impaired or by individuals with insucient experience and knowledge, if supervised or trained to use the appliance in asafe manner and understand potential dangers. Children must not play with the appliance. Cleaning and maintenance operations must not be carried out by children unless supervised by an adult.

16. Do not use the device if water is leaking from it.

Correct use of the product signicantly improves the blood circulation nthe legs, giving alasting and pleasant warm feeling (increase in skin temperature). Aregular massage bath can improve blood circulation in the legs and indirectly to the entire area of the lower limbs. The built-in heating body under each massage roller keeps the required temperature throughout the whole period of activation of the device with the rotary switch. The stimulating points on the surface of the massage device are like gentle ngers caressing your feet and performing the most eective refreshing and strengthening massage. The eectiveness of the massage can be controlled by slightly increasing or decreasing the pressure on the foot in the massage area. In addition, there are air jets on the device that create awarm relaxing bubble bath for your feet. Running massage

1. Before connecting the device to the electricity outlet, the rotary control knob must be in the OFF position.

2. Do not connect or disconnect the device to/from the electricity outlet if your feet are in the water bath or

if your hands are wet.

3. Place the device on an even surface. The anti-slip rubber feet prevent unwanted movement of the device.

4. Fill up the massage device with warm water (with the requested temperature); the volume of water should

not exceed the maximum level line. This device is designed to keep the water at apleasant temperature, so do not to increase it. Never use the massage device without water!

5. Sit comfortably, put your feet on the massage rollers and using the rotary control knob, set the desired

mode (vibration massage, bubble massage, massage with or without heating the bath). Functional modes available: Warm bath + vibration massage + bubble massage + infra radiation [W + B+ M+ IR] To use the foot vibration massage in astimulating temperature, turn the control knob to the position [W+B+ M+ IR]. Warm bath + bubbles [W+ B] For arelaxing massage in pleasant warm water with astimulating bubble massage, turn the control knob to the position [W+ B]. Vibrating massage + infra radiation [M + IR] To use the foot massage in the water bath, turn the control knob to the position [M + IR]. Ending the massage

• After ending the massage, rst turn the switch to the OFF position then remove your legs and disconnect the device from the outlet. Do not forget that you must not stand up in the device!

• When pouring out the water, tilt the device e.g. above the bath, so that the water can run out of the spout. Using the cosmetic brush Make sure that the switch is in the OFF position. Insert the batteries into the body of the brush (note the correct polarity). Cleaning feet Make sure that the disk with the brush is correctly inserted in the device (do not use without the disk inserted). Turn the device on and gently move the brush across the sole, until the dirt is removed. Do not push too hard otherwise the roller will stop rotating. Use the speed switch to select low (LOW) or high (HIGH) speed or rotation or completely switch o the device by moving the switch into the OFF position. Grinding feet Exchange the cleaning ring with the grinding disk. Choose either the rough or the ne grinding disk. Activate the device and gently move with the disk over the hardened skin, which will be gradually sanded until reaching the required smoothness. Only use on dry skin.GB

Wipe the remnants of the abraded skin from the feet. Dry the feet thoroughly. Attention: Do not apply to one area of the foot for longer than 3-4 seconds. In the case of irritation or redness of the skin, stop the procedure. Final treatment of the feet To soften the sanded skin, use the head with the sponge. Apply cream to the foot or the head of the brush and roll the brush across the feet until the cream is absorbed.

CLEANING AND MAINTENANCE

The massage device is adevice for personal care, not awash bath. Before the massage, wash your legs in clean water. The deposited particles block the air nozzles and limit the bubble eect. Unplug the device and let it cool down before cleaning. After use, rinse the massage device with clean water. Never immerse the entire device in water! Use awet cloth for cleaning. Do not use aggressive chemical substances or abrasive cleaners. To prevent the build up of bacteria, regularly clean the device and the individual components with mild disinfectant. The massage device can only be stored after it has been completely turned o by main switch disconnected from the outlet, is completely empty and has dried and cooled down. Before storing, wrap the power cord around the winding holder on the lower side of the device. Never hinge the device at the cable. Never connect the device into the electricity outlet if the cable is partially wound around the device. Wipe the body of the cosmetic device with asoft, wet cloth. Clean the replacement heads with running water and leave to dry. TECHNICAL DATA Nominal voltage: 220-240 V~ 50/60 Hz Nominal input power: 90 W Supply of brush: 2× AA batteries DC 3 V, 3 W(not included in thepackage) Water temperature: 23°C ± 5°C Up to leg size 49 IPX4 – Protection against spraying water WARRANTY: The following situations void the warranty: Incorrect or inappropriate handling of the device, failure to observe safety measures applicable to the device, the use of force, alterations or repairs made by aparty other than an authorized service centre. Components subject to normal wear and tear are not covered under the warranty.

USE AND DISPOSAL OF WASTE

Wrapping paper and corrugated paperboard – deliver to scrapyard. Packing foil, PE bags, plastic elements – throw into plastic recycling containers. DISPOSAL OF PRODUCTS AT THE END OF LIFETIME Disposal of electric and electronic equipment (valid in EU member countries and other European countries with an implemented recycling system)The represented symbol on the product or package means the product shall not be treated as domestic waste. Hand over the product to the specied location for recycling electric and electronic equipment. Prevent negative impacts on human health and the environment by properly recycling your product.Recycling contributes to preserving natural resources. For more information on the recycling of this product, refer to your local authority, domestic waste processing organization or store, where you purchased the product. This product complies with EU directive requirements on electromagnetic compatibility and electrical safety. The instruction manual is available at website www.ecg-electro.eu. Changes in text and technical parameters reserved.