iCMPDA2T02 - Flat screen mount Chief - Free user manual and instructions

USER MANUAL iCMPDA2T02 Chief

Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief® and Centris™ are trademarks of Milestone AV Technologies. All rights reserved.

IMPORTANT WARNINGS AND CAUTIONS!

WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.

WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer's responsibility to make sure all components are properly assembled and installed using the instructions provided.

WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer's responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component.

WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer's responsibility to make sure the combined weight of all components attached to the iCMPDA2 does not exceed 75 lbs (34kg).

AVISOS Y PRECAUCIONES IMPORANTES!

PNEOCTEPEKHEI. PNEOCTEPEKHEI npBQATNT BTOBHOCTBaX B03MOXHOCTN NOEPKDEHIN Hn pa3pyeHnOBOPyDABHH,ecnBu He cnePyTe 3a COOTBeCTAoyuMMH NCHTpydAAH

PNDYPTPEKDEHE.OTKa3HHTaB,THO6JIOHOCTbIO NOHTb, H CIEp2BaTb 3A BOEMV HCTpykuaMMMQEET npAECTeK OpeuHOM TYeCHOMy NOpeKBeHHo NOpeKDeHeM NOcOpDyauHaHNO,IMCObO6KeHDO p6aHnPHRapAHINI 1TO -0rTeCTBHeNHOCTbMOCTaXHHa YQoCTeBPHTbCA, VTO BOE KOMMOHHTbI DORKHM IbOPa3OM cOpaHbY yCTaHBAHMa INCNtBbOaHMe npoeDcTaBBHxH HcTpykui.

PDEYYPKEKDEHNE. OTKa3 oecenehaBt aekbaHTyO CTpykTyO cHbI 3T0o KOmHOHEHMA KOTe pRBeCTxO CepbEHO TYENCHOMY NOpeBdHEnIO NnOBpETHb Hs OocpyBaHHe! 3TO -OTBCTBHeNHOCTM MOHTaONKa YQDOCTeBPRTCACTpykTA, K KOTOPo PNNOKHeH 3TO KOMHOENT, MOKet NOpeKATb nTb p33obEbnHbB Bc acce 60cbOpDaaHN. XyKeHneCTpyOyy KaK TpeSyTErpeN MeKT AOKomHOHt

IMPORTANT! If the display has a 100 × 100mm recessed mounting hole pattern, then display must be mounted to swing arm (A) before swing arm is installed to base plate (B). See "INSTALL DISPLAY, 100 × 100mm Recessed Mounting Hole Pattern". Continue below after display is installed.

CAUTION: PERSONAL INJURY MAY OCCUR IF SWING ARM COLLAPSES AGAINST FINGERS! Be alert, keeping hands and fingers out of pinch points during installation.

1. Slide swing arm mounting bracket (A) down into base plate (B).
2. Secure swing arm (A) to base plate (B) by tightening screw with hex key (K).

3 INSTALL DISPLAY

IMPORTANT! Proceed as directed below:

If installing a display with a 200x100, 200x200, 300x300, 400x200, or 400x400mm mounting hole pattern, proceed to Step 3A.
If installing a display with a 100× 100mm mounting hole pattern, proceed to step 3B or 3C, as applicable.

3A

200x100, 200x200, 300x300, 400x200 or 400x400 Mounting Hole Pattern

Attaching Vertical Brackets

WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Only use hardware provided or specified by manufacturer.

1. Determine and mark the vertical center position between the left side upper and lower mounting holes in display.
2. Determine and mark the vertical center position between the right side upper and lower mounting holes in display.
3. Orient vertical mounting bracket (E) so that mounting holes are on top and mounting slots are on bottom.
4. Align mounting holes and slots in vertical mounting bracket (E) with upper and lower mounting holes in display.
5. Adjust vertical mounting bracket (E) position until mark made in Step 1 aligns with center mark in vertical mounting bracket (E).
6. Secure left side vertical mounting bracket (E) to display using two Phillips pan head screws (N through AA).

NOTE: Also use #10 flat washers (BB) if using screws N or P.

NOTE: If the display has a recessed mounting surface, protrusions or a power box, a spacer and longer mounting hardware must be placed between the display and vertical mounting brackets (E).
7. Repeat Steps 3 through 6 for right side vertical mounting bracket using the same hole locations to align brackets horizontally.

3B

100 x 100mm Flush Mounting Hole Pattern

IMPORTANT! This procedure only applicable when 100 × 100 ~mm mounting holes on back of display are flush with back surface of display, OR brackets (C, E) were previously installed per Step 3A.

WARNING: EXCEEDING THE WEIGHT CAPACITY CAN

RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installer's responsibility to make sure the combined weight of all components attached to the iCMPDA2 does not exceed 75 lbs (34 kg).

1. Ensure Centris bracket can swivel and tilt easily, yet still be tight enough to hold display in desired position. Adjust as required before proceeding. See "ADJUSTMENT".

UPTION: USING SCREWS OF IMPROPER SIZE CAN IMAGE DISPLAY! Screws should easily and completely pad into display mounting holes.

1. Using a Phillips screwdriver, install two screws (M) into upper threaded mounting holes in back of display (or in brackets C, E; if installed).

2. Thread screws completely into display (or in brackets C, E; if installed), then back out 3 complete turns.

WARNING: INADEQUATE THREAD ENGAGEMENT IN DISPLAY CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Back out screws ONLY as necessary to allow installation of Centris bracket!

1. Lift and align display so that screws in back of display (or in brackets C, E; if installed) fit into upper teardrop mounting holes in Centris bracket. Lower display into place.

NOTE: DO NOT tighten screws at this time.

1. Using Phillips screwdriver, install two screws (M) through lower teardrop mounting holes in Centris bracket into display (or in brackets C, E; if installed).
2. Tighten all four screws (M). Do not overtighten!

3C

100 x 100mm Recessed Mounting Hole Pattern

IMPORTANT! This procedure only applicable when 100 × 100 ~mm mounting holes on back of display are recessed into back surface of display.

WARNING: EXCEEDING THE WEIGHT CAPACITY CAN RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installer's responsibility to make sure the combined weight of all components attached to the iCMPDA2 does not exceed 75 lbs (34 kg).

1. Ensure Centris bracket can swivel and tilt easily, yet still be tight enough to hold display in desired position. Adjust as required before proceeding. See "ADJUSTMENT."
2. Carefully place display face down on protective surface.

CAUTION: USING SCREWS OF IMPROPER SIZE CAN DAMAGE DISPLAY! Screws should easily and completely thread into display mounting holes.

1. Place four spacers (CC) over mounting holes in display back.
2. Orient mount so that teardrop mounting holes in Centris bracket are aligned with holes in four spacers (CC).

WARNING: INADEQUATE THREAD ENGAGEMENT IN DISPLAY CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT!

1. Using a Phillips screwdriver, install four screws (P) through four teardrop mounting holes in Centris bracket and spacers (CC) into display. Tighten all four screws (P). Do not overtighten!
2. Continue with "INSTALL SWING ARM TO BASE PLATE".

4 ADJUSTMENT

1. To adjust pitch tension, slightly loosen or tighten adjustment screw as required using hex key (K).

NOTE: If display is mounted to swing arm (A) then first disconnect all cables and remove display (Refer to "INSTALL DISPLAY").

1. To adjust extension and swivel tension, slightly loosen or tighten adjustment screws as required using hex keys (K, L).

5 CABLE MANAGEMENT

CAUTION: Ensure that adequate cable slack exists for movement of display, and that cables will not be pinched by installation of covers (D) or screws (J).

1. Move swing arm (A) to fully extended position.
2. Carefully position cables in cavity located in lower portion of each arm.
3. Using Phillips screwdriver, install covers (D) using screws (J).

INSTALACION DE LA PLACA DE BASE EN LA PARED

WAARSCHUWING! ONEIGENLIJEK

INSTALLATIE KAN LEIDEN TOT VALLEN VAN

MONTAGEONDERDELEN, DIT KAN

RESULTEREN IN ERNSTIGE VERWONDINGEN

DYNPEXDEHME. HEPABINbHAR

YCTAOHBAKOXTIPNBECTKINPADEHEIO YCTOPOCTBAIbB3BATCBEP3BHeJE TPABMBNEPCOHAIHA INOBPEKEHEIA OEOPYDOBAHAR3ATPPEJTAETCRHOJIb308aB HepeoRnHNKxpenE.CnepyTcNkO308aT ToLAnoXpenE, npoeCtAeHHnnn nnpapeeHnhN KnpmeneHHNO pno3sOgKeTneM.

1. HauDHTe IOTMTBeTe CEENTpaHHe NOONOKEHNE NO BcTbVKAA MKNY DBeBMM BcXHHM NHOKKMHMQTOHUMNTOBCTVNRMOHOTCA
   2.Haikinte NOTMTBeTae UENTPAHoe NOONKHEWNE NO BEPTKAMMSEy PnBbIMBE BXHHMMN HIXHXMM MOHTAKBHMM OTBCTPMM MOHOTOPA.
   3.YCTAHONITE XPOHJINB HEPITKABHIOX
   KPEIHNHIAE (E) TAMOKO5P3OM, YTOSSMOHTKHBM
   OTBEPTPNNAXADNRCB BEXPYA, A MOHTKHOB
   CNOTH-BHH2X.
2. COBECTHEMOCTKHOBTBCTHINCTOHTI B EMTKHOHMOCHXPOHTHEE (E) C BEXHAMN HIKOHKMOMTOXHOBTBCTHMMOTTOPA
3. Pemyipnye tata nolexenchen beetvkrnshoro KOKHUTHEA (E) DO COOMENCHENBEETVKRNSHAOI

MONTAK cHTpNbHoro KPOHTeHa

1. Pnmpneite nentpahnbnk hpoonrHc (C) K BETKANbHM KPOOHHTeHAM (E) npa NOMO YetbEX BnHOu Philips c roNkoM4 Mx 12 MM (N) NtHAPTE NOONX 56 No 10 (BB).
2. ⅡPENPENIECMPDA2KPOHHTAHTAEPYTAaBAAHTA Phillips c roLoXoM4 X8MM (M) aBepxHHe MoTAXHHe OTABPCTAR.
3. 3aBepuTeMOTaxICMPDA2.3xKpyTbAaBHHTa Phillips c nooaxoM A4 x8 MM (M) aHxHOe MOHTaxOHe OTABCTy.
4. Ipepeepre kuary 3B

3B

Ua6bONKpeneKbIXbOTBcETHn 100x100 MM, OTBcETHn paaclonokBeH3anoDnIoo

BAKHO! 3ra npoueUpya npmMnMa tonbko ecnn xpeNEXhae otBpCTHa HA aedn CTKeE dnCnne paoonoxnxno noa5owny 100x100 MM 3anodnupc c3adne noapekXocTbdo qtnner, INIIN paabe HbB yctAtoAnoeHc KxoBc (C,E) cornao hwaam 3A.

PENPYNPNKDEHNE: PEBBIIIEHNE DONYCTVMOJ

BECOBON HAPY3KMOKET NOBIEb CEPbE3HbIE
TPABMbI NIOBPEKDEHEO BOPYIOBAHRII Iuio. OcyueCTaHoue yctahOxy, o63aHO npocneBaTa 3e TM, Tc0bU cympaHae MaCC aoeX KOOMOHTeo, yctAHoNnHHAAx KaICMPDA2, nepebausana 34 K (75ykyTob).

1. 06paHte BmHnHae: oKo3 Centr ngKHeRKO npOaHbAeBcN HAKNOHbTb, HO npI TOM ONGoBt bHbATiHHTy DOCTAOHO DRTO, TTObYdEeKbHbAeDIOH N BHYXOH NOXENHBe. PpExdeHem nepeKoDyI K dALbHIHMM DECTBHr, pN eHcKoDnMOCTn OTPynlnoPobat, CM. -PEYINPOBKA.

PNEDOCTEPEXEHNE:PNINCNOB3OBAHNN

BHTOB HENIOJXIOJUERO PA3MEPA BO3MOXHO NOPEBXDEHNE DACNPIER BHTTHDOLIOHOHIO

1. Kectoofoa3nohtoeepno3aaephytaaiaHTa(M) eaepeHne p608eXpeeneknHe oraepTnHa 3a3nei cteke dncnner (knu ackoxC E: ecnyctananeH).
   3 enoNtctbAo aeeepnByAeHbAaIaonnn (na 8 cXob6C E, ecn ytaanaoBnHa), aTeM oTaePbHbHa na 1nohbs ao0pba

PNEYNTPEKDEHHE:HEIOCTAOHOE 3ABHHAHHEBHTOBINKPENIEHMAACNPIER MOKETIPVBECTNIADEHMOPEPNIEHARIIOBNEbCEPE3HBeTPABMIINIOBPEKDEHHEO BOPDYBOAHIRTOPOAHOHHOHTOIOTIOKOHOHO

3C

W650H KpEeKbIx OTBepTm 100 x 100 MM C 3aRny6nHem

BAXHOI 37a npouzya pnpimnEe TONTOO eCNI KPNEXKHe OteAepCTH, paonionkHeHne no 100 x 100 MM. 2aaybEyHb a 3a4ho n oaeXPoctb cIacn.

PNEYDPEKDEHNE: PNEBbIeHEMEOITGYCTYMOM BECOBMOHAPy3MOKETNOBIEb CEPbE3HbIE TPABMbIINIOBPEKDEHME OOBPOYOBAHNRIIooocyeaONBOy.063aHO npocneHbTaTMe,HTo6bIcymmaepnaMaCCaBCX KOMTOHHeTo,yctaHOaENHHx HAICMPDA2.HepeBaunana 34KT (75fHTO8).

1. 06pAHTNE HMMHMK CKOBA CentrIs OIOONHRAPEKNOOBOPAMATBn HAKNOKHTCB,HO pRt AOTM DIOKHO BmT BAtTHyDcTATOHNOIra TORO,TObU yzePMAHNTN EHNHIN BHYHXOMNOEKNHIM.PeXeK YEMpeKPOBtK KdAeHHeuMMeDCTABNMR, PnEHOKOAMCITN OTEPYNPOBAt C.M.-PEYTNPOBKA.
   2.Axypathno nonoxkntb dncnneR nueebo CTPOHOH BHN H BAUNTHYIO NOBepXHOCTb.

PNEOCTEPEXHEME:IPNINIOB3OBAHIMBVHTOB HENOPOXIUEROPA3MEPA BO3MOXHOIOBPEXHEME DNCIIIE! BnHbdoKbneNOHNOCbBOAAMHBATCBxKPENEXHBE OTEPCBdnONN.

1. Pnoknty hte tyepe dctanpnohne styn (CC) na kpenexohne otepctna 3aedher ctenke daenner.
2. PaoonooKbI Kpenee TaK, T0bI KaJIeNBeHbIe XpeKeNkHbIe OaBepCnA a CxObe Centriis CoMeCTINNC b C oTaePCNnM B HET BPEX dactaONuHbX TByNKX [CC].

PNEYPTPEKDEHNE:HEOCTATOHHOE3ABHHNBAHNE BVHTOB PIPKNPEJIENM DNCIEI MoKET IPNBECTK IN PADEHNO KEPENIEHNRIOBIEHc CEPbE3HbIE TPABMbI NIM OBPEXDEHNE OBOPYDBOAHI

1. Kpeo06ba3n0y 3aBepHy7e BnVt (P) hepe7e3pKaneNkbnxKpenexohnxOteBcTBA Cbo6eCentrix tBynncc (C) aKnvnn.3Aatnyb 0eBteBnVt (P). He nepetnmbata?
2. NpeepnKpaednyKPENIEHNEIOBOPOTHO KPOHHTEHA KIIACTVHE OCHOBAHNA

4

PEYNIPOBKA

I JINHAYPIMPOBCHNBI PDCKAAHNI PAHNOHE CNEA OCAABHTIK N3ATRHYPTBYPERYPMPOOBHH BHNTH KHOHOMC WEEETPAHNOROPOB(K).
PIMEMAHHE: Ecra pncnnepepehnn Knoporophty npohreHy (A), Chanaa otocepeHHb AOB kane n chte pncn (Cm. YCTAHOBKA DCNTNPIER.).
2.Длрургбхснчсдсрпгдзнлгдзнлгдзнлгдзнлгдзнлгдзнлгдзнлгдзнлгдзнлгдзнлгдзнлгдзнлгдзнлгдзнлгдзнлгдзнлгдзнлгдзнлгдзнлгдзнлгдзнlгдзнlrgd3n

5

POKIADKA KABENEI

PNEOCTEPEKHEH: Pnocpnd3a Tm, YIO6i KaBne IINMENI pOBVANHc, DcOATAOHcDPRNepemaenrA dnCnne, He n 3aoKnnncnnpraYtOahONBe KxHKe (D) HnBHToB (J).

1. YCTAHOBNTb KPOHWTReH (A) a NONHOCTbIO BHTRHYTOE NOXEHNE.
2. AxypatthopnoipnolaohtbKa65Ba n noocctk，pactonokkeHHux C Hxohc hctopohai 06bx XactreXPOHHTHe.
3. 3aepenntb Kpbk (D) bHTAMJ (J) c NMOUbKO pecto06pa3HO OTBepTK

2

MONTERING AF SVINGARM PÅ BUNDPLADE

USA·8401 Eagle Creek Parkway, Suite 700·Savage, Minnesota 55378·800.572.1373

EMEA·[phone]

www.icmounts.com

©2009 Milestone AV Technologies. The iC Logo and StowAway are trademarks of Chief Manufacturing,

a products division of Milestone AV Technologies, a Duchossois Group Company. All rights reserved

Patents and patents pending. Milestone AV Technologies, Savage, MN 55378, USA

8800-002045 Rev 00

11/09