WP-300 - CREATIVE - Free user manual and instructions

USER MANUAL WP-300 CREATIVE

According to R&TTE Directive (1999/5/EC) Company Name Company Address

Creative Technology Ltd

31, International Business Park Creative Resource Singapore 609921

Declare under our sole responsibility that the product(s):

Product Model Number:

Indoor and Outdoor Usage

To which this declaration relates are in conformity with the following standard(s):

Notice for Australia / New Zealand

DECLARATION OF CONFORMITY N136

This product complies with the requirements of the ACMA Radiocommunications

(Electromagnetic Compatibility) Standard 2008.

Refer to the following information to use your product safely, and to reduce the chance of electric shock, short-circuiting, damage, fire, hearing impairment or other hazards. Improper handling may void the warranty for your product. For more information, read the warranty available with your product.

• Do not dismantle or attempt to repair your product. Refer all servicing to authorized repair agents. • Do not expose your product to temperatures outside the range of 0°C to 45°C (32°F to 113°F). • Do not pierce, crush or set fire to your product. • Keep your product away from strong magnetic objects. • Do not subject your product to excessive force or impact. • Do not expose your product to water or moisture. If your product is moisture-resistant, take care not to immerse your product in water or expose it to rain.

Notice for Singapore

Complies with IDA Standards DB00148

Technical documentation for this product(s) is retained at the following address:

Company Name Company Address

: Creative Technology Ltd

: 31, International Business Park Creative Resource Singapore 609921

03EF045000000 Rev A When a conductive apparatus such as earphones, is used in close proximity with a CRT television or

CRT monitor, the latter may emit an electrostatic discharge. This electrostatic discharge can be felt as a static shock. While this static shock is usually harmless, it is good practice to avoid close contact with CRT devices when using earphones. Do not listen to audio on your earbuds or headphones at high volume for prolonged periods of time as hearing loss may result. For users in the United States, go to www.hei.org for more information.

Do not listen to your audio device at high volume when driving, cycling or crossing the road, especially in heavy traffic, or in any other traffic condition where such use will hinder safe travel on the roads.

We recommend that consumers be extremely cautious when using this device on the road.

Do not attempt to remove the embedded battery.

The product must be disposed of according to local environmental regulations. To replace the battery, return your product to your regional support office. For product service information, go to www.creative.com. • Do not expose to excessive heat such as sunshine, fire or the like CAUTION: Risk of explosion if battery is replaced by incorrect types.

Bluetooth Wireless Device

The shortwave radio frequency signals of a Bluetooth device may impair the operation of other electronic and medical devices.

Switch off the device where it is prohibited. Do not use the device in medical facilities, aircraft, refueling points, close to automatic doors, automatic fire alarms or other automatically controlled devices Keep this device at least 20cm from pacemakers and other medical devices. Radio waves may impair the operation of pacemakers and other medical devices.

FOR INTEGRATED BATTERY This product contains a Lithium ion/ polymer battery that should only be removed by an authorized recycling centre. By recycling this product at your local authorized recycling centre or the place of purchase, the battery will be removed and recycled separately.

Thank you for selecting Creative’s PURE WIRELESS Headphones. This documentation aims to guide you in making full use of the headphones. Fully charge the headphones before first use. Then you need to “pair” the headphones once with your Bluetooth audio device before enjoying subsequent automatic playback.

• Connect the Left earcup to your laptop or computer using the supplied USB cable • On the Left earcup, the indicator lights up in Red. When fully charged, this indicator turns Green • You can listen and operate the headphones while charging Pairing new audio devices • Press and hold the Power/Pair button for more than 4 seconds on the Right earcup until the indicator lights up in Blue and blinking rapidly • Turn on Bluetooth search function on your audio device • Select “Creative WP-300 Headphones” and if prompted for a Passcode, key in “0000” • Once paired, the Blue indicator on the Right earcup blinks slowly Playback from audio devices • Turn on Bluetooth function on your paired audio device • Press and hold the Power/Pair button on the Right earcup until the indicator lights up in Green and blinks slowly. The headphones automatically searches for the last paired device. Once connected, the indicator turns Blue and blinks slowly. In certain cases, you may need to press the Play button to establish connection. • You can now Play or Pause music playback, skip forward or reverse tracks, and make volume adjustments Clear or Reset headphones • Press and hold the Volume Down “-” and Power/Pair

buttons for more than 6 seconds to clear the paired audio devices

If the headphones malfunction, reset it by supplying USB power, then press the Volume Up “+” and Power/ Pair buttons for about 1 second

• Once the headphones are powered on, if it is unable to connect to a last paired device or failed to pair with a new device within 5 minutes, the headphones will automatically shut down. List of button, indicator and connector functions Button

Press and hold to for about

2 seconds to power on the headphones. Press and hold for about 4 seconds to power off the headphones. In off mode, press and hold for more than 4 seconds to activate Pairing mode.

Press to play. Press again to pause playback.

Press to change to the next or previous track. Press and hold to fast forward or reverse track (this function is device dependent).

Press ‘+’ to increase or press ‘-‘ to decrease volume. A beep tone is emitted at maximum volume level.

Pause headphones to mute.

/ Next, Forward / Previous, Rewind Track / Volume Up / Volume Down

Green and blinks slowly: automatically searching and attempts to connect to the last paired device. Blue and blinks slowly: connected to a paired device.

Blue and blinks rapidly: in pairing mode and is ready to pair with a new device. Red and blinks twice: powering off the headphones. Red and blinks slowly: low battery, charge headphones soonest. This is accompanied by a beep tone every 2 minutes.

Red: charging headphones.

Green: headphones fully charged.

earcup light indicator

earcup light indicator

USB charging connector

Use the supplied USB cable for charging the headphones via a laptop or computer.

Technical Specifications:

• Driver: 34mm Neodymium magnet • Frequency Response: 18Hz ~ 22kHz • Impedance: 32ohms • Sensitivity (1kHz): 102dB/mW • Wireless Technology: Bluetooth 2.1 + EDR (Enhanced Data Rate) • Bluetooth Profiles: A2DP (Wireless stereo Bluetooth), AVRCP (Bluetooth remote control) • Audio Codec: apt-X, SBC • Operating Range: Up to 10m / 33ft • Power Supply: Rechargeable Lithium Ion battery, 3.7V, 240mAh • Charge / Playback: 1 hour / 8hours • Net Weight: 107 g / 3.5oz

Next, Forward / Previous, Rewind Track

Volume Haut / Volume Bas

7.Micro-USB charging connector

Use the supplied USB cable for charging the headphones via a laptop or computer.

Safety And Regulatory Information

The following sections contain notices for various countries: Caution This product is intended for use with FCC/CE certified computer equipment. Please check the equipment operating/installation manual and/or with the equipment manufacturer to verify/confirm if your equipment is suitable prior to the installation or use of the product.

Notice for USA FCC Part 15: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Caution To comply with the limits of the Class B digital device, pursuant to Part 15 of the FCC Rules, this device must be installed with computer equipment certified to comply with

All cables used to connect to the computer and peripherals must be shielded and grounded. Operation with non-certified computers or non-shielded cables may results in interference to radio or television reception. Modification Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the device.

Federal Communication Commission (FCC)

Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. It passes the SAR test or OET 65 standard.

This Class B digital apparatus complies with Canadian ICES003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Son Fonctionnement est soumis aux deux conditions suivantes: (1) Le matériel ne peut étre source D’interférences et (2) Doit accepter toutes les interférence reques, Y compris celles pouvant pouvant provoquer un fonctionnement indésirable. Canadian Class B Statement This digital device does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment

European Compliance This product conforms to the following: EMC Directive 2004/108/EC Mains operated product for the European market comply with Low Voltage Directive 2006/95/EC and Commission Regulation(s) Implementing Directive (2005/32/EC). Communication / RF wireless products for the European market comply with R&TTE Directive 1999/5/EC. CAUTION: To comply with the Europe CE requirement, this device must be installed with CE certified computer equipment which meet with Class B limits. All cables used to connect this device must be shielded, grounded and no longer than 3m in length. Operation with non-certified computers or incorrect cables may result in interference to other devices or undesired effects to the product. MODIFICATION: Any changes or modifications not expressly approved by Creative Technology Limited or one of its affiliated companies could void the user’s warranty and guarantee rights.