Q: How to set the time on the Majority Bard?

To set the time on your Majority Bard, follow these steps: Press the MENU/INFO button to access the main menu Navigate to "System Settings" and confirm with the OK button Select "Time/Date" Choose the clock format: 12 hours (with AM/PM) or 24 hours Select the update method: Update from DAB Update from FM Update from the network (you need to set your time zone) No update (for a complete manual setting) Set Daylight Saving Time to ON if applicable in your area Confirm your settings These settings are usually done during the initial setup. Use the navigation dial to move between options and the OK button to confirm each selection.

Q: How to use the 45 RPM adapter on the Majority Moto turntable?

The 45 RPM adapter (part C ) is included with your Majority Moto turntable and is located in the holder next to the platter. This accessory is essential because 45 RPM records have a smaller center hole than 33 RPM and 78 RPM records, and the adapter allows them to be properly centered on the turntable's spindle. Here’s how to use the 45 RPM adapter on your Majority Moto: Remove the adapter from its holder next to the platter Slightly lift your 45 RPM record Place the adapter on the central spindle of the platter (the pivot in the center) Then place your 45 RPM record on the adapter Set the speed selector to 45 RPM (the 33/45/78 switch on top of the turntable) Proceed to play normally by opening the clip of the tonearm and placing it on your record Important: make sure the adapter is stable on the spindle before placing your record. The record must rest firmly on the adapter to ensure proper rotation and avoid skipping or premature wear of the record. If you do not use an adapter for a 45 RPM record, the record may not spin consistently or may be misaligned, which would affect audio quality. Once you finish playing, remove the record and replace the adapter in its designated holder.

Q: What are the 4 EQ settings of the Majority Bowfell Axis Dolby?

The Majority Bowfell Axis Dolby features 4 equalizer presets accessible via the remote control by pressing the EQ button: EQ1 - Music EQ2 - Movies EQ3 - News/Dialogue EQ4 - Sports In addition to these presets, you can manually adjust the audio settings by pressing the Audio Settings button on the remote to access the configuration mode. You will then be able to adjust: Bass : from -5 to +5 (default = 0) Treble : from -5 to +5 (default = 0) Use the +/- buttons to increase or decrease these values in configuration mode.

Question 1

How to set the time on the Majority Bard?

Accepted Answer

To set the time on your Majority Bard, follow these steps:

Press the MENU/INFO button to access the main menu
Navigate to "System Settings" and confirm with the OK button
Select "Time/Date"
Choose the clock format: 12 hours (with AM/PM) or 24 hours
Select the update method:
- Update from DAB
- Update from FM
- Update from the network (you need to set your time zone)
- No update (for a complete manual setting)
Set Daylight Saving Time to ON if applicable in your area
Confirm your settings

These settings are usually done during the initial setup. Use the navigation dial to move between options and the OK button to confirm each selection.

Question 2

How do I set the time on the Majority Homerton 2 radio?

Accepted Answer

To set the time on your Majority Homerton 2 radio, you have two options: during the initial setup or through the settings menu.

During the first power-on

A setup wizard automatically launches. It prompts you to choose the clock format:

12-hour format: displays AM for morning and PM for afternoon
24-hour format: classic hh:mm display

You then need to choose the time update mode:

Automatic update: select DAB, FM, or Internet (network). The time synchronizes automatically according to the radio mode you use most
Manual setup: choose "No Update", then enter the date in dd-mm-yyyy format and the time in hh:mm format. Use the navigation dial to change each value and press OK to confirm

The wizard also offers to configure the time zone and enable daylight saving time if your country observes it.

Via the Settings menu

After the initial setup, you can change the time by accessing the system menu. Press the MENU button, then select the "TIME/DATE" section to:

Manually change the time and date
Toggle between automatic and manual update
Adjust the time zone
Manage daylight saving time

Quick shortcut

On the remote control, press and hold the CLOCK button to quickly access the time settings. You can also briefly press this button to see the current time displayed.

Once set, the time is retained even in the event of a power outage. If you opted for an automatic update, ensure that the selected radio mode (DAB, FM, or Internet) is active for synchronization to occur correctly.

Question 3

I am not receiving any DAB stations on my Majority Robinson 2IR radio

Accepted Answer

If your Majority Robinson 2IR radio is not receiving any DAB stations, several simple checks may resolve this issue.

Preliminary Checks

Antenna deployed - Ensure that the wire antenna is fully extended. A retracted antenna prevents DAB reception.
DAB mode activated - Press the MODE button or the dedicated DAB button to switch to DAB mode. The device will automatically perform a scan function to search for available stations.

DAB Search Process

Once in DAB mode, the device automatically scans the multiplexes in the range DAB 174 - 240 MHz. A progress bar indicates the scanning progress. Wait for the scan to complete fully - this may take a few minutes.

If no station is found

Change location - Move the radio to a window or a higher location. DAB reception may be obstructed by walls or metal structures.
Manual search - Access the manual settings for the multiplexes (identified from 5A to 13F) and test several DAB channels.
Check local availability - Verify that DAB is available in your area and with your broadcasting operator.

If after these steps no DAB station appears and the signal strength remains zero or very weak, there may be a hardware issue with the DAB tuner of your device.

Question 4

How to use the 45 RPM adapter on the Majority Moto turntable?

Accepted Answer

The 45 RPM adapter (part C) is included with your Majority Moto turntable and is located in the holder next to the platter. This accessory is essential because 45 RPM records have a smaller center hole than 33 RPM and 78 RPM records, and the adapter allows them to be properly centered on the turntable's spindle.

Here’s how to use the 45 RPM adapter on your Majority Moto:

Remove the adapter from its holder next to the platter
Slightly lift your 45 RPM record
Place the adapter on the central spindle of the platter (the pivot in the center)
Then place your 45 RPM record on the adapter
Set the speed selector to 45 RPM (the 33/45/78 switch on top of the turntable)
Proceed to play normally by opening the clip of the tonearm and placing it on your record

Important: make sure the adapter is stable on the spindle before placing your record. The record must rest firmly on the adapter to ensure proper rotation and avoid skipping or premature wear of the record.

If you do not use an adapter for a 45 RPM record, the record may not spin consistently or may be misaligned, which would affect audio quality. Once you finish playing, remove the record and replace the adapter in its designated holder.

Question 5

What are the 4 EQ settings of the Majority Bowfell Axis Dolby?

Accepted Answer

The Majority Bowfell Axis Dolby features 4 equalizer presets accessible via the remote control by pressing the EQ button:

EQ1 - Music
EQ2 - Movies
EQ3 - News/Dialogue
EQ4 - Sports

In addition to these presets, you can manually adjust the audio settings by pressing the Audio Settings button on the remote to access the configuration mode. You will then be able to adjust:

Bass: from -5 to +5 (default = 0)
Treble: from -5 to +5 (default = 0)

Use the +/- buttons to increase or decrease these values in configuration mode.

Question 6

What should I do if my Majority Robinson 2IR radio produces no sound despite the adjustments made?

Accepted Answer

If your Majority Robinson 2IR radio produces no sound despite the adjustments made, here are several steps to follow to try to resolve this issue:

1. Check the volume and audio source

Make sure the volume is turned up and that the mute function is not activated.
Change the audio source (for example, switch from FM radio to Bluetooth or another input) to check if the problem comes from a specific source.

2. Check the power supply

Ensure that the radio is properly plugged in or that the batteries are in good condition and inserted correctly.
Try another electrical outlet or replace the batteries if necessary.

3. Inspect the connections and speakers

If you are using headphones or external speakers, check that the connections are secure.
Test without headphones to see if sound comes from the built-in speakers.

4. Reset the radio

Perform a factory reset via the radio menu to eliminate any potential software issues.

5. Test with another source or station

Try to tune into another radio station or use another Bluetooth source to check if the problem persists.

If after all these checks your Majority Robinson 2IR radio still produces no sound, it may be a hardware defect requiring repair or replacement.

Question 7

How to adjust the audio balance on the Majority Robinson 2IR radio?

Accepted Answer

The Majority Robinson 2IR radio features a built-in equalizer system that allows you to customize the sound via bass and treble settings. Here’s how to access these settings:

Method 1 - Quick access via the EQ button:

Press the EQ button on your radio to directly access the Equalizer menu
The menu displays the available presets: NORMAL, CLASSIC, ROCK, POP, JAZZ, MY EQ and MY EQ PROFILE SETUP
Use the navigation buttons to select MY EQ PROFILE SETUP to create a custom profile, then press SELECT to confirm

Method 2 - Access via the Settings menu:

Press the MENU button on your radio
Use the navigation buttons (up/down) to select System Settings, then press SELECT
Select Equaliser and press SELECT
Choose MY EQ PROFILE SETUP for a custom adjustment

Adjusting Bass/Treble:

Once in MY EQ PROFILE SETUP, select [Bass/Treble] using the navigation buttons and press SELECT
Use the navigation buttons to choose the desired level (increase bass for more power, increase treble for more clarity)
Press SELECT to confirm your selection
Press the BACK button to exit, select [YES] to save your custom equalizer profile
The screen will display Equaliser Saved once the changes are saved

You can also use the predefined equalizer presets (CLASSIC, ROCK, POP, JAZZ) for an immediate adjustment suited to your musical style. If you wish to return to the standard configuration, simply select the NORMAL preset in the Equalizer menu.

User manual Majority : user manuals and guides in PDF

Models Majority most viewed

Browse manuals Majority by appliance type

Recent questions about devices Majority