User manual PHILIPS Shaver : 553 free PDF user manuals

Q: Can the PowerTouch PT717 razor be cleaned under running water?

Yes, you can clean the PowerTouch PT717 razor under running water , but you must follow important precautions. Recommended cleaning method Unplug the device before cleaning and remove the detachable cord Rinse the shaving head for 30 seconds under warm water Clean the hair compartment and the inside of the head, then the outside Essential precautions Never exceed 80°C - Make sure the water is not too hot to avoid burns Do not fully immerse the razor in water or use it in the shower The power adapter must remain dry - never clean it under water It is normal for water to flow from the lower socket during rinsing, as the internal electronic components are protected

Q: What color blinks on the Philips Series 9000 shaver when it is charging?

The charging indicator of the Philips Series 9000 behaves differently depending on the battery status: Flashing orange : the shaver is in normal charging mode. The lower indicator flashes progressively, followed by other indicators until fully charged. This same orange flashing also indicates that there are 5 minutes or less of shaving time remaining when you are using the device. Flashing orange and white alternately : fast charging. After 3 minutes of charging, the shaver has enough power for a full shaving session, and the indicator flashes alternately orange and white until fully charged. All charging indicators lit continuously : the battery is fully charged. The indicators remain steadily lit (without flashing) for about 30 minutes, then the display automatically turns off. Note: When you turn off the shaver and the battery is low, the lower indicator continues to flash orange for a few seconds after shutdown. This quickly disappears.

Q: What are the symbols and indicators of the PHILIPS 7000 shaver?

The PHILIPS 7000 shaver has several LED indicators and symbols that inform you about its charging status, operation, and maintenance tasks. Charging Indicators Flashing orange and white charging indicator : Indicates that the shaver is charging with sufficient fast charge. Lower charging indicator : Gradually lights up during charging to show progress. Flashing orange indicator : Signals a low battery (less than 5 minutes of remaining autonomy). Display Symbols Plug symbol : Indicates that the shaver is connected to power. Battery symbol : Displays the available charge level. Lock symbol : Signals that travel lock is activated, preventing any accidental start. Shaver symbol : Reminds you when it's time to replace the shaving heads. Jet Clean System (CC models) If your shaver is equipped with the Jet Clean system, you will also see: “Empty tank” symbol : Indicates that the cleaning reservoir needs to be filled. Flashing cleaning symbol : Appears during the automatic cleaning program. Flashing drying symbol : Appears during the automatic drying phase.

Q: Why does the charging base light always stay on?

This is a completely normal behavior. The base light remains active as long as the base is plugged into the mains, as it indicates that the base is powered and ready to charge your shaver. Interpretation of the base indicator Solid green light : the shaver is on the base and its battery is fully charged (charging complete, maintenance charging). Flashing orange and white light : the shaver is in fast charge and will soon be ready for use. Flashing orange light : normal charging in progress or low battery of the shaver. To turn off the base light If you do not want the indicator to stay on, simply unplug the base from the electrical outlet . The light will turn off immediately. This is the only way to completely stop the power to the base. In summary: light on = base powered and operational. This is intended to signal to you that the base is ready to charge your Philips Series 9000 shaver at any time.

Q: How to disable the safety lock on the PHILIPS SERIES 5000 electric shaver?

The PHILIPS SERIES 5000 electric shaver is equipped with a safety lock system to prevent accidental activation during transport or storage. To disable this lock, follow the steps below: Procedure to disable the lock Press and hold the power button for about 3 seconds. The lock indicator should turn off, indicating that the shaver is unlocked. If this does not work, try pressing the power button and another button (for example, the cleaning button) simultaneously for a few seconds, depending on the exact model. If in doubt, check that the battery is sufficiently charged, as a low level may prevent the lock from being disabled. Once the lock is disabled, you can use your shaver normally. To reactivate the lock, repeat the same operation. This function is designed to protect your device and prevent any unintentional activation.

Q: What should I do if my Philips AquaTouch S7320 razor does not turn off?

If your Philips AquaTouch S7320 razor does not turn off, here are several steps to follow to try to resolve this issue: 1. Check the power button Make sure to press the power button correctly. On some models, you need to hold the button down for a few seconds to turn off the device. 2. Unplug the razor If the razor is connected to the charger, it may remain on. Unplug it and try to turn it off again. 3. Clean the button and the area around it Sometimes, dirt or debris can block the button. Gently clean around the button with a dry cloth or a small brush. 4. Reset the device Although this model does not always have a reset function, turn it off, remove the battery if possible (or let it discharge completely), then recharge it and try to turn it on and off again. 5. Check for signs of malfunction If the razor makes unusual noises, lights are flashing, or if the button seems stuck, this may indicate a technical problem requiring repair. If none of these solutions work, it is advisable to contact Philips customer service or an authorized repair center for professional assistance.

Q: What do the alert indicators on the Philips Series 9000 electric shaver mean?

The alert indicators on the Philips Series 9000 electric shaver indicate different operating states or potential issues. Here are the main indicators and their meanings: Charging indicator: This indicator lights up when the shaver is charging. It turns off or changes color once the battery is fully charged. Cleaning indicator: Some models have an indicator that lights up to signal that it is time to clean the shaver, which is important for maintaining optimal performance. Shaving head replacement indicator: This indicator lights up when the shaving head is worn and needs to be replaced to ensure maximum efficiency. Error indicator: In case of a problem, such as a motor blockage or another anomaly, an error indicator may light up. It is advisable to turn off the shaver and check for obstructions or other issues. These indicators help you better understand the condition of your shaver and ensure proper maintenance to extend its lifespan and performance.

Q: How to remove the shaving head from the Philips Aquatouch Series 5000 and how to clean the device without a cleaning brush?

Removing the shaving head: Make sure the device is turned off. Detach the shaving head from the shaver by pulling straight up. Important: do not twist the shaving head while removing it, as this could damage it. Once removed, you can proceed with cleaning or replacing it. Cleaning without a specific brush: If you do not have the cleaning brush provided with your Philips Aquatouch Series 5000, you can clean your device using only hot water. Open the three shaving heads one by one and rinse them under hot water for 30 seconds, as well as the three hair compartments. Ensure that the water is not too hot to avoid burns. After rinsing, shake off the excess water from the shaving heads and let them dry completely in the air. It is important not to dry the shaving head with a towel or cloth, as this could damage the shaving elements. Once completely dry, you can reattach the shaving head by inserting the tab into the slot located on the top of the shaver, then sliding it down until it clicks. Deep cleaning: If you wish to perform a more thorough cleaning without the Jet Clean system, here is the complete procedure. With the shaving head detached and the three heads open, press the release tab of the attachment until it opens. You can then remove the blade from the grid and clean it with hot water. Also clean the inside of the grid with hot water. Then replace the blade by orienting the trimmer block downwards, press on the attachment, close the shaving heads, and reattach the shaving head to the body of the device. For optimal maintenance, clean your Philips Aquatouch Series 5000 razor after each use by simply rinsing the shaving head under hot water. This ensures optimal shaving performance and prolongs the lifespan of your device.

Models PHILIPS Shaver most viewed

User manual PHILIPS Shaver : user manuals and guides in PDF

Models PHILIPS Shaver most viewed

Other categories PHILIPS

Recent questions about Shaver PHILIPS