Series 5000 S5444 - Razor PHILIPS - Free user manual and instructions

Product Type	Electric Shaver
Model	Philips Series 5000 S5444
Dimensions (approx.)	15 x 6 x 10 cm
Weight	240 g
Power Source	Rechargeable Li-Ion battery
Charging Time	1 hour
Run Time	50 minutes
Quick Charge	5 minutes for one shave
Shaving System	MultiPrecision blade system
Trimmer	Pop-up trimmer for sideburns and moustache
Wet & Dry Use	Yes, can be used with or without gel/foam
Waterproof	Yes, fully washable under running water
Display	LED battery indicator
Cleaning	Rinse under tap; removable head for thorough cleaning
Head Replacement	Every 2 years; use Philips SH50 replacement heads
Battery Replacement	Replaceable by service center
Voltage	100-240 V auto-adjust
Accessories	Protective cap, charging stand, travel case (depending on variant)
Warranty	2 years

Frequently Asked Questions - Series 5000 S5444 PHILIPS

How do I clean my Philips Series 5000 S5444 shaver?

Rinse the shaver head under warm running water after each use. Remove the shaver head and clean it thoroughly once a week. Use the supplied brush to remove hair clippings. Do not use abrasive cleaners.

How long does the battery last and how do I charge it?

The lithium-ion battery provides 50 minutes of cordless use after a full 1-hour charge. A 5-minute quick charge gives enough power for one shave. Charge using the supplied adapter or charging stand. The LED indicator shows battery status.

Can I use the shaver in the shower?

Yes, the Philips Series 5000 S5444 is fully waterproof. You can use it in the shower or with shaving foam/gel. Rinse under running water after use.

How often should I replace the shaving heads?

For optimal performance, replace the shaving heads every 2 years or when you notice a decline in shaving comfort. Use Philips SH50 replacement heads.

Does the shaver have a pop-up trimmer?

Yes, it features a pop-up trimmer located on the back of the shaver. Slide it up to trim sideburns or moustache. Use it dry for best results.

Can I use the shaver while it is charging?

No, the Philips Series 5000 S5444 is designed for cordless use only. You cannot shave while the shaver is connected to the charger. You can use it cordless after charging.

What should I do if the shaver does not turn on?

First, ensure the battery is charged. If it still doesn't turn on, check if the shaver head is properly attached or if there is a blockage. If the issue persists, contact Philips customer service.

Is the shaver suitable for sensitive skin?

The MultiPrecision blade system cuts hair at the skin level comfortably. However, if you have very sensitive skin, try using the shaver with shaving foam or gel in a wet shave.

Where can I buy replacement parts?

Replacement heads (SH50), trimmer units, and other accessories are available from Philips official website or authorized retailers. Always use genuine Philips parts.

How do I reset the replacement reminder?

After installing new shaving heads, press and hold the on/off button for 7 seconds until the indicator flashes. The reminder is now reset. Refer to the user manual for details.

USER MANUAL Series 5000 S5444 PHILIPS

Philips electric shaver

Model number

S5444/03

User manual

Main unit

Protective cap

Charging adapter

Guidance in English 17~34

● Warranty

Warranty and after-sales service 35

Specifications 36

Free repair regulations 38

Warranty certificate ...... last page

Be sure to observe

Safety precautions

Protective cap

Cheek

Under the chin

From inside the cheek to the neck

Under the nose

How to attach the protective cap

How to store

When disposing of the shaver

English

Important safety information

Read this important information carefully before you use the appliance and its

accessories and save it for future reference.

The accessories supplied may vary for different products.

Danger

-Keep the supply unit dry.

Warning

- To charge the battery, only use the detachable supply unit (HQ8505) provided with the appliance. - The supply unit contains a transformer. Do not cut off the supply unit to replace it with another plug, as this causes a hazardous situation. - This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. - Always unplug the shaver before you clean it under the tap. - Always check the appliance before you use it. Do not use the appliance if it is damaged, as this may cause injury. Always replace a damaged part with one of the original type. - This appliance contains batteries that are non-replaceable. - Do not open the appliance to replace the rechargeable battery.

Caution

- Never use water hotter than 60°C to rinse the shaver. - Only use this appliance for its intended purpose as shown in the user manual. - For hygienic reasons, the appliance should only be used by one person. - Never use compressed air, scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the appliance. - Water may drip from the socket at the bottom of the shaver when you rinse it. This is normal and not dangerous because all electronics are enclosed in a sealed power unit inside the shaver. - Do not use the supply unit in or near wall sockets that contain an electric air freshener to prevent irreparable damage to the supply unit.

Electromagnetic fields (EMF)

This Philips appliance complies with all applicable standards and regulations regarding exposure to electromagnetic fields.

General

- This shaver is waterproof. It is suitable for use in the bath or shower and for cleaning under the tap. For safety reasons, the shaver can therefore only be used without cord. The supply unit is suitable for mains voltages ranging from 100 to 240 volts.

- The supply unit transforms 100-240 volts to a safe low voltage of less than 24 volts.

English

General description (Fig. 1)

1 Protection cap 2 Click-on shaving unit 3 Shaving unit release button 4 On/off button 5 Travel lock symbol 6 'Unplug for use' symbol 7 Battery charge indicator 8 Supply unit 9 Small plug

Introduction

Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.

philips.com/welcome.

The display

Battery charge indicator

Quick charge: When the shaver does not contain enough energy for one shave, the battery charge indicator flashes orange quickly. When the shaver is plugged in and the battery charge indicator starts flashing white slowly, the shaver contains enough energy for one shave. While the shaver continues to charge, the battery charge indicator flashes white slowly until the product is fully charged.

Battery fully charged

When the battery is full, the battery charge indicator lights up white continuously. Note: When the battery is full, the display turns off automatically after 30 minutes.

Battery low

When the battery is almost empty, the battery charge indicator flashes orange.

'Unplug for use' reminder

The 'unplug for use' symbol flashes to remind you that you have to disconnect the product from the power outlet before you can switch it on.

Travel lock

When you are going to travel, you can lock the shaver to prevent it from accidentally turning on.

Activating the travel lock

1 Press the on/off button for 3 seconds to use the travel lock mode.

While you activate the travel lock, the travel lock symbol lights up continuously. When the travel lock is activated, the travel lock symbol flashes.

Deactivating the travel lock

1 Press the on/off button for 3 seconds.

-While you deactivate the travel lock, the travel lock symbol lights up briefly and the shaver produces a short sound. The shaver turns on and is now ready for use again.

Charging

Before first use, charge the shaver for at least 2.5 hours without interruption and until the battery charge indicator shows that the battery is full. This is needed to make maximum use of the battery capacity.

Subsequent charges take approx. 1 hour.

Note: You cannot use the appliance while it is charging.

Charging with the power cord

1 Make sure the product is turned off. 2 Put the small plug in the shaver and connect the power plug to any 100V to 240V AC outlet. Use only the power cord provided. The display of the shaver indicates that the shaver is charging. 3 After charging, remove the power plug from the wall outlet and pull the small plug out of the product.

Using the product

Always check the product and all accessories before using. Do not use the product or any accessory if it is damaged, as this may cause injury. Always replace a damaged part with one of the original type.

Turning the shaver on and off

Shaving

-To turn on the shaver, press the on/off button once. -To turn off the shaver, press the on/off button once.

After turning the shaver off, the display lights up for a few seconds and shows the remaining battery charge.

This product can only be used without a cord.

This shaver is suitable for use in the bath or shower. For safety reasons, it is therefore not possible to use the shaver while it is connected to the power outlet for charging.

-For the best results on skin comfort, pre-trim your beard if you have not shaved for 3 days or longer.

Dry shaving

1 Turn on the shaver. 2 Move the shaving heads over your skin in circular movements to catch all hairs growing in different directions. Make sure each shaving head is fully in contact with the skin. Exert gentle pressure for a close, comfortable shave.

Note: Do not press too hard, as this can cause skin irritation.

3 Turn off and clean the product after each use.

Wet shaving

For a more refreshing shave, you can also use this shaver on a wet face with shaving foam or gel.

1 Apply some water to your skin.

2 Apply shaving foam or gel to your skin.

3 Rinse the shaving unit with warm water to ensure that the shaving unit glides smoothly over your skin.

4 Turn on the shaver.

5 Move the shaving heads over your skin in circular movements to catch all hairs growing in different directions. Make sure each shaving head is fully in contact with the skin. Exert gentle pressure for a close, comfortable shave.

Note: Rinse the shaving unit regularly to ensure that it continues to glide smoothly over your skin.

6 Dry your face.

7 Turn off the shaver and clean it after each use.

Note: Make sure that you rinse all shaving foam or gel off the shaver.

Cleaning and maintenance

Cleaning the shaver

Clean the shaver after every use for optimal performance (see 'Cleaning and maintenance').

Note: While rinsing shaving heads, water may drip out of the base of shaver. This is a normal occurrence. Internal electric parts are in a waterproof compartment so the shaver will be protected against water damage.

Caution: Always check if the water is too hot, to prevent burning your hands.

1 Turn on the shaver.

2 Rinse the shaving unit with warm water.

3 Turn off the shaver. Press the release button to open the shaving unit.

4 Rinse the hair chamber and shaving head holder with warm water.

5 Carefully shake off excess water and let the shaving head holder air-dry completely.

Note: Never dry the shaving unit with a towel or tissue, as this may damage the shaving heads.

6 Close the shaving head holder ('click').

Thorough cleaning method

Note: We advise you to clean the shaving heads thoroughly once a month or when the shaver does not shave as well as it used to. 1 Turn off the shaver. 2 Press the release button to open the shaving unit. 3 Pull the shaving head holder off the bottom part of the shaving unit. 4 Turn the retaining rings counterclockwise and remove them. 5 Remove the shaving heads from the shaving head holder. Each shaving head consists of a cutter and guard. Note: Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally put a cutter in the wrong shaving guard, it may take several weeks before optimal shaving performance is restored. 6 Clean the cutter and guard with warm water.

7 Put the cutter back into the guard.

8 Place the shaving heads in the shaving head holder.

Note: Make sure that the projections of the shaving heads fit exactly into the recesses of the shaving head holder.

9 Place the retaining rings back onto the shaving head holder and turn them clockwise ('click').

-Each retaining ring has two recesses and two projections that fit exactly in the projections and recesses of the shaving head holder.

-Turn the ring clockwise until you hear a click and the ring is fixed.

Note: Hold the shaving head holder in your hand when you reinsert the shaving heads and reattach the retaining rings. Do not place the shaving head holder on a surface, as this may cause damage to the shaving heads.

10 Reinsert the hinge of the shaving head holder into the slot of the shaving unit. Close the shaving head holder.

Storage

We advise you to let the appliance and its attachments dry before you put the protection caps on the attachments or store the shaver in the pouch.

Note: The accessories supplied may vary for different products. The box shows the accessories that have been supplied with your product.

Put the protection cap on the shaver to protect it from any dirt accumulation.

Replacement

Replacing the shaving heads

For maximum shaving performance, we advise you to replace the shaving heads every two years. Replace damaged shaving heads immediately. Always replace the shaving heads with original Philips shaving heads (see 'Ordering accessories').

1 Switch off the appliance.

2 Press the release button to open the shaving unit.

3 Pull the shaving head holder off the bottom part of the shaving unit.

4 Turn the retaining rings counterclockwise and remove them. Place them aside in a safe place.

5 Remove the shaving heads from the shaving head holder. Discard the used shaving heads immediately to avoid mixing them with the new shaving heads.

6 Place the new shaving heads in the shaving head holder.

Note: Make sure that the projections of the shaving heads fit exactly into the recesses of the shaving head holder.

7 Place the retaining rings back onto the shaving heads and turn them clockwise to reattach the retaining ring. Each retaining ring has two recesses and two projections that fit exactly in the projections and recesses of the shaving head holder.

-Turn the ring clockwise until you hear a click to indicate that the ring is fixed.

Note: Hold the shaving head holder in your hand when you reinsert the shaving heads and reattach the retaining rings. Do not place the shaving head holder on a surface, as this may cause damage to the shaving heads.

8 Reinsert the hinge of the shaving head holder into the slot of the shaving unit. Close the shaving head holder ('click').

Ordering accessories

To buy accessories or spare parts, visit www.philips.com/parts-and-accessories or go to your Philips dealer. You can also contact the Philips Consumer Care Center in your country (see the international warranty leaflet for contact details).

The following accessories and spare parts are available:

-SH50 Philips shaving heads

Note: The availability of the accessories may differ by country.

Recycling

-This symbol means that this product shall not be disposed of with normal household waste (2012/19/EU).

-This symbol means that this product contains a built-in rechargeable battery which shall not be disposed of with normal household waste (2006/66/EC). Please take your product to an official collection point or a Philips service center to have a professional remove the rechargeable battery.

-Follow your country's rules for the separate collection of electrical and electronic products and rechargeable batteries. Correct disposal helps prevent negative consequences for the environment and human health.

Removing the rechargeable shaver battery

Only remove the rechargeable battery when you discard the appliance. Before you remove the battery, make sure that the appliance is disconnected from the wall socket and that the battery is completely empty.

English

Take any necessary safety precautions when you handle tools to open the appliance.

Be careful, the battery strips are sharp.

1 Remove the screw in the back of the shaver. 2 Remove the back panel.

3 Take out the power unit.

4 Bend the snap hooks aside and remove the transparent cover of the power unit.

5 Lift out the battery holder and cut the wires with a pair of cutting pliers or scissors.

6 Bend the battery tags aside with a pair of cutting pliers or a screwdriver.

7 Remove the rechargeable batteries.

Warranty and support

If you need information or support, please visit www.philips.com/support or read the international warranty leaflet.

Warranty restrictions

The shaving heads (cutters and guards) are not covered by the terms of the international warranty because they are subject to wear.

Troubleshooting

This chapter summarizes the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, visit www.

philips.com/support for a list of frequently asked questions or contact the Consumer Care Center in your country.

Shaver

Problem Possible cause Solution

The appliance does not work when I press the on/off button.	The appliance is still attached to the wall socket. For safety reasons, the appliance can only be used without cord.	Unplug the appliance and press the on/off button to switch on the appliance.
	The rechargeable battery is empty.	Recharge the battery.
	The travel lock is activated.	Press the on/off button for 3 seconds to deactivate the travel lock.
	The shaving unit is soiled or damaged to such an extent that the motor cannot run.	Clean the shaving heads thoroughly or replace them.

Problem Possible cause Solution

The appliance does not shave as well as it used to.	The shaving heads are damaged or worn.	Replace the shaving heads.
	Hairs or dirt obstruct the shaving heads.	Clean the shaving heads in the regular way or clean them thoroughly.
Water is leaking from the bottom of the appliance.	During cleaning, water may collect between the inner body and the outer shell of the appliance.	This is normal and not dangerous because all electronics are enclosed in a sealed power unit inside the appliance.

Warranty and After-Sales Service

MyPhilips Registration Information