Speed-XL HQ8170 - Razor PHILIPS - Free user manual and instructions

Product Type	Electric Rotary Shaver
Brand	Philips
Model	Speed-XL HQ8170
Dimensions (Approx.)	6 x 2 x 2 inches (15.2 x 5.1 x 5.1 cm)
Weight (Approx.)	0.5 lbs (0.23 kg)
Power Source	Rechargeable Battery
Battery Type	Lithium-ion
Charging Time	1 hour
Usage Time	45 minutes
Voltage	100-240V, 50-60Hz
Washable	Yes, fully washable under running water
Cleaning	Rinse shaving heads under warm water; use included brush for stubble
Shaving Heads	3 self-sharpening rotary heads
Trimmer	Pop-up trimmer for sideburns and mustache
Display	LED battery indicator (low, charging, full)
Travel Lock	Yes, prevents accidental activation
Protection	Overcharge protection, automatic shut-off after 8 hours
Accessories	Cleaning brush, protective cap, charging cord
Warranty	2 years limited warranty
Repairability	Shaving heads and battery replaceable; other parts serviceable by skilled users

Frequently Asked Questions - Speed-XL HQ8170 PHILIPS

How do I clean the Philips Speed-XL HQ8170 shaver?

After each use, rinse the shaving heads under warm running water while the shaver is on, then turn off and remove the heads to dry. Use the cleaning brush to remove stubborn stubble. For deeper cleaning, soak the heads in warm water with a mild soap, then rinse thoroughly.

How long does the battery last and how do I charge it?

The lithium-ion battery provides approximately 45 minutes of cordless use after a 1-hour charge. Connect the supplied charging cord to the shaver and a 100-240V outlet; an LED indicator shows charging status. A full charge takes 1 hour; an 8-minute quick charge gives enough power for one shave.

Can I use the shaver while it's charging?

No, the shaver is designed for cordless use only. It cannot be operated while connected to the charger. Always disconnect before shaving.

How often should I replace the shaving heads or blades?

For optimal performance, replace the shaving heads every 12 to 18 months. The heads are self-sharpening but eventually wear out. Replacement heads can be purchased online or at Philips service centers. The trimmer does not require replacement.

Is the shaver waterproof?

Yes, the shaver is fully washable and can be rinsed under running water. However, it is not designed for bathing or submersion. The charging contacts must be kept dry.

Why does the shaver seem less efficient?

Causes include dull or clogged heads, low battery, or hair length. Clean the heads thoroughly, ensure full charge, and cut longer hairs with the trimmer first. If problem persists, replace the shaving heads.

Does the shaver have a travel lock?

Yes, the shaver features a travel lock to prevent accidental activation. Press and hold the on/off button for 3 seconds to lock or unlock. The LED will flash to confirm.

What accessories are included with the Philips Speed-XL HQ8170?

The package includes the shaver, a cleaning brush, a protective cap for the shaving heads, and a charging cord. A travel case may be available separately depending on region.

Where can I find replacement parts for the HQ8170?

Replacement shaving heads (model HQ8 or compatible) and batteries are available from Philips authorized dealers, online retailers, and the Philips official website. Check your user manual for part numbers.

How do I replace the shaving heads?

Turn off the shaver and remove the head assembly by pulling it off. Insert the new heads until they click into place. Ensure the retaining ring is properly seated. Dispose of old heads responsibly.

USER MANUAL Speed-XL HQ8170 PHILIPS

Read this user manual carefully before you use the appliance and save it for future reference.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Only use the powerplug supplied.
• The powerplug transforms 100-240 volts to a safe low voltage of less than 24 volts.
• The powerplug contains a transformer. Do not cut off the powerplug to replace it with another plug, as this causes a hazardous situation.
• Do not use a damaged powerplug.
• If the powerplug is damaged, always have it replaced with one of the original type in order to avoid a hazard.
• Make sure the powerplug does not get wet.
• Charge and store the appliance at a temperature between 15° C and 35° C.
• Never immerse the charging stand in water nor rinse it under the tap.
• Do not recharge the shaver in a closed pouch.
• Always unplug the shaver before you clean it under the tap.
• The shaver complies with the internationally approved IEC safety regulations and can be safely cleaned under the tap.

Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt.

• This washable shaver is not suitable for shaving in the shower.
• Do not immerse the shaver in water.

- Water may leak from the socket at the bottom of the appliance, when you rinse it. This is normal and not dangerous because all electronics are enclosed in a sealed shell inside the shaver.

Electromagnetic fields (EMF)

This Philips appliance complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user manual, the appliance is safe to use based on scientific evidence available today.

Charging

Make sure the appliance is switched off before you start to charge it.

Charging takes approx. 1 hour.

You can also shave without charging by connecting the shaver to the mains.

Charge indications

Charging

When you start charging the empty shaver, the bottom light flashes red. When the battery contains enough power for one shave, all lights start flashing green sequentially.

Battery fully charged

When the battery has been fully charged, all green lights are on.

A few hours after charging, all lights go out.

Remaining battery capacity

The amount of power left in the battery is indicated by the number of lights that are on. The battery capacity is only shown when you switch the shaver on or off.
- When all lights burn green, the battery is 100% charged.
- When the bottom light burns green, 20% of the battery capacity is left.

Battery running low

When the battery is running low, the bottom light turns red.

When you switch off the shaver, this light flashesblinks a few times.

Cordless shaving time

A fully charged shaver has a cordless shaving time of up to 55 minutes.

Charging the appliance

Charge the shaver when the bottom light burns or flashes red.

Do not recharge the shaver in a closed pouch.

1 Put the appliance plug in the shaver.
2 Put the powerplug in the wall socket.
3 Remove the powerplug from the wall socket and pull the appliance plug out of the shaver when the battery has been fully charged.

Charging stand

You can also charge the appliance by placing it in the charging stand, if provided.

Place the shaver properly in the plugged-in charging stand.
Lift the shaver from the stand without tilting it.

Using the appliance

Shaving

1 Switch the shaver on by pressing the on/off button once.

The blue light ring around the on/off button goes on to indicate that the motor is running.

Note: When you switch the shaver on, all lights go on and then the remaining battery capacity is shown for a few seconds.
2 Move the shaving heads quickly over your skin, making both straight and circular movements.

• Shaving on a dry face gives the best results.
• Your skin may need 2 or 3 weeks to get accustomed to the Philips shaving system.

3 Switch the shaver off by pressing the on/off button once.

The blue light ring around the on/off button goes out.

ENGLISH8

4 Clean the shaver (see chapter ‘Cleaning and maintenance’).
5 Put the protection cap on the shaver every time you have used it, to prevent damage.

Trimming

For grooming sideburns and moustache.

1 Open the trimmer by pushing the slide downwards.

The trimmer can be activated while the motor is running.

2 Close the trimmer ('click').

Cleaning and maintenance

The light above the tap symbol starts flashing after every shave to remind you that the shaver needs to be cleaned (except when the bottom light burns red).

Regular cleaning guarantees better shaving performance.

The normal way to clean the appliance is to rinse the shaving unit and the hair chamber with hot water every time you have used the shaver.

Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt.

Note: Water may leak from the socket at the bottom of the appliance when you rinse it. This is normal and not dangerous.

Every day: shaving unit and hair chamber

1 Switch off the shaver, remove the powerplug from the wall socket and pull the appliance plug out of the shaver.
2 Press the release button to open the shaving unit.
3 Clean the shaving unit and the hair chamber by rinsing them under a hot tap for some time.

Make sure you clean the inside as well as the outside of the shaving unit.

4 Close the shaving unit and shake off excess water.

Never dry the shaving unit with a towel or tissue, as this may damage the shaving heads.

5 Open the shaving unit again and leave it open to let the appliance dry completely.

You can also clean the hair chamber without water by using the brush supplied.

Every six months: shaving heads

1 Open the shaving unit, turn the lock anticlockwise (1) and remove the retaining frame (2).

2 Clean the cutters and guards with the brush supplied.

Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally mix up the cutters and guards, it may take several weeks before optimal shaving performance is restored.

3 Put the shaving heads back into the shaving unit. Put the retaining frame back into the shaving unit and turn the lock clockwise.

4 Close the shaving unit.

Trimmer

Clean the trimmer every time you have used it.

1 Switch off the shaver, remove the powerplug from the wall socket and pull the appliance plug out of the shaver.
2 Clean the trimmer with the brush supplied.
3 Lubricate the trimmer teeth with a drop of sewing machine oil every six months.

Charging stand

You can clean the charging stand with a moist cloth.

Storage

Put the protection cap on the shaver to prevent damage.

The appliance can be stored in the pouch supplied.

The shaver can be stored in the charging stand, if provided.

Replacement

Replace the shaving heads as soon as the light above the shaving unit symbol starts flashing.

Replace damaged or worn shaving heads with HQ9 Philips shaving heads only.

Note: Do not mix up the cutters and the guards to guarantee optimal shaving performance.

1 Switch the shaver off, remove the powerplug from the wall socket and pull the appliance plug out of the shaver.

2 Press the release button to open the shaving unit.

ENGLISH12

3 Turn the lock anticlockwise (1) and remove the retaining frame (2).

4 Remove the shaving heads and place new ones in the shaving unit. Put the retaining frame back into the shaving unit and turn the lock clockwise.

Make sure that the projections of the shaving heads fit exactly into the recesses.

5 Close the shaving unit.

Accessories

The following accessories are available:

• HQ8500/HQ8000 powerplug.
• HQ9 Philips Shaving Heads.
• HQ110 Philips Shaving Head Cleaning Spray (not available in China).
• HQ8010 car cord.

Environment

• Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this, you help to preserve the environment.
• The built-in rechargeable battery contains substances that may pollute the environment. Always remove the battery before you discard and hand in the appliance at an official collection point. Dispose of the battery at an official

collection point for batteries. If you have trouble removing the battery, you can also take the appliance to a Philips service centre. The staff of this centre will remove the battery for you and will dispose of it in an environmentally safe way.

Disposal of the battery

Only remove the battery if it is completely empty.

1 Remove the powerplug from the wall socket and pull the appliance plug out of the shaver.
2 Let the shaver run until it stops and undo the two screws at the back of the shaver.
3 Undo the two screws in the hair chamber.

4 Undo the three screws in the power unit.

5 Bend the 4 hooks aside (1) to take out the power unit (2).

Be careful, the hooks are very sharp.

6 Remove the power unit cover by means of a screwdriver.
7 Remove the battery.

Be careful, the battery strips are very sharp.

Do not connect the shaver to the mains again after the battery has been removed.

Guarantee & service

If you need information or if you have a problem, please visit the Philips website at www.philips.com or contact the Philips Customer Care Centre in your country (you find its phone number in the worldwide guarantee leaflet). If there is no Customer Care Centre in your country, go to your local Philips dealer or contact the Service Department of Philips Domestic Appliances and Personal Care BV.

Guarantee restrictions

The shaving heads (cutters and guards) are not covered by the terms of the international guarantee because they are subject to wear.

Troubleshooting

1 Reduced shaving performance.

- Cause 1: the shaving heads are dirty. The shaver has not been rinsed long enough or the water used was not hot enough.

Clean the shaver thoroughly before you continue shaving. See chapter 'Cleaning and maintenance'.

- Cause 2: long hairs are obstructing the shaving heads.

Clean the cutters and guards with the brush supplied. See chapter ‘Cleaning and maintenance’, section ‘Every six months: shaving heads’.

- Cause 3: the shaving heads are damaged or worn. Replace the shaving heads. See chapter 'Replacement'.

2 The shaver does not work when the on/off button is pressed.

- Cause 1: the battery is empty.

Recharge the battery. See chapter 'Charging'.

- Cause 2: the appliance is not connected to the mains.

Put the powerplug in the wall socket.

3 The shaving unit has come off the shaver.

- The shaving unit has not been placed correctly. - If the shaving unit becomes detached from the shaver, you can easily put it back by inserting the hinge into the slot in the rim of the hair chamber and pushing it home until it locks into place ('click').

Penting

Pengisian daya

Jangan mengisi ulang pencukur di dalam kantong tertutup.

1 Buka unit pencukur, putar kunci berlawanan arah jarum jam (1) lalu lepaskan bingkainya (2).

충전

- Perkakas mematuhi peraturan keselamatan antarabangsa IEC yang diluluskan dan boleh dibersihkan dengan air paip.

Mengecas

Apabila anda mula mengecas pencukur yang kosong, lampu bawahnya berkelip merah. Apabila bateri mengandungi kuasa yang mencukupi bagi satu cukuran, semua lampu mula berkelip hijau secara berurutan.

Jangan mengecas semula pencukur di dalam pau tertutup.

4 Longgarkan ketiga-tiga skru di dalam unit pencukur.

การชาร์แบตเตอรี่

การเปลี่ยนอะไรหล่

TIÊNG VIÊT66

Sạc điện

充電

從充電座中直直地拔起電鬍刀。

使用此電器

除毛

適合刮除鬢角及髭髴。

1 向下推開關按鈕打開鬢角刀。

馬達轉動時即可以使用鬢角刀。

2 關閉鬢角刀 (喀噠一聲)。

清潔與維護

請確實清洗電鬍刀組的外殼與內部。

4 蓋上電鬍刀組，並將多餘的水甩乾。

2 請使用隨附的毛刷清潔刀具及刀網。

每次使用鬚角刀後，請進行清潔。

電池棄置

必須將電池電力完全耗盡後才能拆卸電池。

4 轉開電源單元上的三個螺絲。

6 利用螺絲起子取下電源裝置的蓋子。

充电

将剃须刀从充电座上提起，不要倾斜。

使用本产品

剃毛

1 按开/关按钮启动剃须刀。

1 向下推动滑块，打开修发器。

当马达运转时，修发器便可以启动。

2 关闭修发器（可听到咔嗒声）。

清洁和维护

每次使用后都要清洁修发器。

3 拧开胡茬储藏室中的两个螺丝。

4 拧开电源部件中的三个螺丝。

6 用螺丝刀将电源部件盖取下。

7 取出电池。 注意，电池带非常锋利。