Q: What to do when button A is flashing during grease filter cleaning?

The flashing of button A indicates that the metal grease filter has reached its saturation limit after approximately 100 hours of actual operation. This is not a problem; it is simply a maintenance reminder. To reset the alert: Clean the metal grease filter (dishwasher safe or by hand with a neutral detergent) Once cleaned and reinstalled, press and hold the button B (for at least 3 seconds) to reset the grease filter saturation counter The flashing will stop after a few seconds Good to know: The grease filter should be cleaned every 2 months under normal use, or more frequently if you cook a lot. This smart alert helps you maintain optimal performance of your hood.

Question 1

What to do when button A is flashing during grease filter cleaning?

Accepted Answer

The flashing of button A indicates that the metal grease filter has reached its saturation limit after approximately 100 hours of actual operation. This is not a problem; it is simply a maintenance reminder.

To reset the alert:

Clean the metal grease filter (dishwasher safe or by hand with a neutral detergent)
Once cleaned and reinstalled, press and hold the button B (for at least 3 seconds) to reset the grease filter saturation counter
The flashing will stop after a few seconds

Good to know: The grease filter should be cleaned every 2 months under normal use, or more frequently if you cook a lot. This smart alert helps you maintain optimal performance of your hood.

Question 2

How to disassemble the motor of the extractor hood for deep cleaning?

Accepted Answer

The manual for the FABER Chloé 70 CG does not provide specific instructions for disassembling the motor. However, here is what you need to know:

Cleaning without disassembling the motor

Grease filters: Clean them every 2 months (or more frequently with heavy use). These metal filters are dishwasher safe.
Exterior cleaning: Use a damp cloth and only a neutral liquid detergent. Turn off the power before any maintenance.

If disassembly of the motor is necessary

For access to the motor (deep cleaning, repair), you must contact an authorized FABER technician. The manual specifies that the hood must be installed by a professional, and the motor contains electrical components that require specialized expertise.

Important: Any internal intervention could void your warranty and pose a risk of electric shock.

Question 3

How to replace the charcoal filter of the FABER TSP 900 hood?

Accepted Answer

The activated charcoal filter of your FABER TSP 900 cannot be washed or regenerated - it must be completely replaced.

Replacement Frequency

According to the product manual, the charcoal filter should be replaced approximately every 4 months of normal operation. If you cook a lot or the appliance is used daily, replace it more often.

Important: Fire Hazard

Failure to adhere to replacement timelines poses a fire hazard. Do not neglect filter maintenance.

Accessing the Filter

The manual does not detail the installation procedure precisely, but it shows a diagram (reference "W") indicating the location of the filter. Generally for this type of hood:

Turn off and unplug the appliance before any intervention
Access the filter compartment (often located above or to the side of the hood)
Remove the old charcoal filter by releasing its fastenings
Insert the new filter and secure it in place

For a precise procedure tailored to your model, refer to the "W" diagram in your manual or contact FABER customer service.

Question 4

How does the touch panel of the FABER VRT 900 hood work, and can it be opened upwards like other models?

Accepted Answer

The FABER VRT 900 hood is equipped with a fixed touch control panel, which means that this panel does not open upwards like some other models of range hoods.

Here are some important points to know about how the touch panel works:

Fixed panel: The touch panel is integrated and cannot be lifted or opened. All controls are accessible directly by touching the visible icons.
Using the controls: To activate the functions of the hood, simply touch the corresponding symbols on the panel. Make sure your fingers are clean and dry to ensure good touch sensitivity.
Maintenance: Regularly clean the panel with a soft, non-abrasive cloth to prevent dirt or grease from affecting the touch responsiveness.

In summary, the touch panel of the FABER VRT 900 is designed to remain fixed and does not open. Its use relies solely on the direct touch of the displayed controls.

User manual FABER Range hood : user manuals and guides in PDF

Models FABER Range hood most viewed

Other categories FABER

Recent questions about Range hood FABER