Q: How to remove the "No PTY" message on the Pioneer DEH-1700UB car radio?

The No PTY message on your Pioneer DEH-1700UB car radio means that the device is not receiving program type (PTY) information from the currently listened radio station. This message does not indicate a malfunction, but rather an absence of specific data transmitted by the station. How to make the "No PTY" message disappear? Change the radio station: Some stations do not broadcast PTY information. Try selecting another station that transmits this data. Check PTY settings: Make sure that the PTY function is enabled in your car radio settings. If you do not want to see this message, you can disable the PTY search. Reset the car radio: A reset can sometimes correct display errors. To do this, turn off the device, then turn it back on or use the reset function if available. In summary, the "No PTY" message is normal when the station does not transmit this type of information. To avoid its display, prefer stations that broadcast PTY data or disable the PTY function in your car radio settings.

Q: What is the remote wire for on the PIONEER DEH-X7800DAB car radio and how to use it?

The remote wire (or remote control wire) on the PIONEER DEH-X7800DAB car radio is a control cable that sends an electrical signal when the device is powered on. This signal automatically activates connected external equipment, such as a power amplifier or the vehicle's automatic antenna relay. Characteristics of the remote wire: Color: Blue cable with a white stripe Voltage and current: Delivers a voltage of 12 V DC with a maximum current of 300 mA Main function: Sends a control signal when the car radio is turned on, and cuts this signal when it is turned off Usage and connection: The remote wire of the DEH-X7800DAB should be connected to the remote turn-on terminal of an external power amplifier, or to the automatic antenna relay terminal of your vehicle. This allows the amplifier or antenna to be activated automatically at the same time as the car radio, without manual intervention. The main advantage is automatic synchronization: when you turn on the car radio, the amplifier starts at the same time, and turns off when you switch off the device. This avoids having to manage the power supply of multiple devices separately and extends the lifespan of the equipment by properly deactivating them. Important points: Ensure that the connection of the remote wire complies with the specifications of your external equipment (check the maximum supported voltage and required current). The wire should not be used to directly power equipment, but only to control its activation. Properly insulate the connections to avoid any short circuit, and feel free to consult your amplifier's manual for the exact color code of its remote control terminal.

Question 1

How to remove the "No PTY" message on the Pioneer DEH-1700UB car radio?

Accepted Answer

The No PTY message on your Pioneer DEH-1700UB car radio means that the device is not receiving program type (PTY) information from the currently listened radio station. This message does not indicate a malfunction, but rather an absence of specific data transmitted by the station.

How to make the "No PTY" message disappear?

Change the radio station: Some stations do not broadcast PTY information. Try selecting another station that transmits this data.
Check PTY settings: Make sure that the PTY function is enabled in your car radio settings. If you do not want to see this message, you can disable the PTY search.
Reset the car radio: A reset can sometimes correct display errors. To do this, turn off the device, then turn it back on or use the reset function if available.

In summary, the "No PTY" message is normal when the station does not transmit this type of information. To avoid its display, prefer stations that broadcast PTY data or disable the PTY function in your car radio settings.

Question 2

How to install a Pioneer DEH-1600UB car radio in a vehicle?

Accepted Answer

The installation of the Pioneer DEH-1600UB car radio in your vehicle can be done by following these essential steps:

1. Preparation before installation

Disconnect the battery of your vehicle to avoid any risk of short circuit or electric shock.
Remove the existing car radio if necessary, using the appropriate tools to avoid damaging the dashboard.

2. Connecting the wiring harness

Use the wiring harness provided with the car radio.
Connect each wire of the car radio to the corresponding wires of your vehicle, respecting the color codes: power, ground, speakers, antenna, etc.
Ensure that the connections are well insulated and secure to avoid any loose contact.

3. Physical installation of the car radio

Insert the car radio into the designated slot in the dashboard.
If necessary, use the brackets or adapters provided to ensure a secure fit.
Secure the device using the screws or clips provided to prevent any movement while driving.

4. Finalization

Reconnect the battery of your vehicle.
Start the vehicle and test the operation of the car radio: check the power on, radio reception, USB playback, sound on each speaker, etc.
If everything works correctly, replace the panels and covers of the dashboard.

By following these steps, you will be able to install your Pioneer DEH-1600UB car radio safely and fully enjoy its features.

Question 3

How to set the clock on the Pioneer DEH-1700UB car radio?

Accepted Answer

To set the clock on your Pioneer DEH-1700UB car radio, follow these simple steps:

Turn on the car radio by pressing the power button.
Access the clock setting mode: Press the "Menu" or "Function" button until the clock setting option appears on the screen. This option is usually represented by a clock icon.
Set the hour: Use the "+" and "-" buttons or the scrolling keys to adjust the hours, then confirm. Repeat the same operation to set the minutes.
Confirm the setting: Press the "Menu" or "Function" button to save the time and exit the setting mode.
Check the display: The correct time should now be displayed on your car radio screen.

This setting allows you to always have the exact time visible on your Pioneer DEH-1700UB car radio, even after turning off the vehicle.

Question 4

Why does my Pioneer MVH-S410BT car radio keep disconnecting from Bluetooth and how can I fix this issue?

Accepted Answer

If your Pioneer MVH-S410BT car radio frequently disconnects from Bluetooth, several causes may be responsible. Here are the solutions to try in order to resolve this issue.

First, check the number of connected Bluetooth devices: If you have registered more than ten Bluetooth devices on the unit (phone, audio player, etc.), they may not function properly. If this is the case, go to the main menu, select SYSTEM, then BTMEM CLEAR and choose [YES] to clear the list of stored devices. This removes the stored Bluetooth data, including paired devices, PIN codes, and call history. Once cleared, re-pair your phone.

Re-pair the phone correctly: Remove the device from your phone by going to Bluetooth settings, then forget the device named “Pioneer MVH-S410BT”. Restart your phone and the car radio, then restart the pairing process. Ensure that the Bluetooth connection is properly established: a Bluetooth icon should appear on the car radio screen.

Reconnect after each shutdown: According to the technical manual, you must reconnect the Bluetooth connection every time you change the source or turn off the unit. If you turn off and on the car, restart the Bluetooth connection from your phone or press BAND/2> on the car radio to establish a new connection.

Check the range and eliminate interference: Keep your phone at a reasonable distance from the car radio (ideally less than 10 meters) without major obstacles. Nearby electronic devices, such as other Bluetooth or Wi-Fi devices, may generate interference. Move these devices away or turn them off temporarily to test the stability of the connection.

Disable AUTO APP CONN if there are incoming call issues: If your device displays a message related to automatic app connection, go to the SYSTEM menu and select [OFF] for [AUTO APP CONN]. This option can sometimes interfere with the stability of the Bluetooth connection.

Reset the car radio as a last resort: If the problem persists, perform a complete reset. Go to the SYSTEM RESET menu and select [YES] to reset all device settings to their factory values. The car radio will automatically restart. You will then need to re-pair your phone from scratch. Alternatively, you can physically press the RESET button located under the front panel (first remove this panel) using a sharp instrument longer than 8 mm.

Question 5

How to use the steering wheel controls with the Pioneer MVH-X360BT car radio?

Accepted Answer

To use the steering wheel controls with your Pioneer MVH-X360BT car radio, follow these steps:

1. Check compatibility

Make sure your vehicle is equipped with compatible steering wheel controls and that the Pioneer MVH-X360BT can work with these controls.

2. Install a steering wheel control adapter

If your vehicle and the car radio are not directly compatible, you will need to install a specific adapter for the steering wheel controls. This adapter acts as an interface between the steering wheel buttons and the car radio.

3. Connect the adapter

Connect the adapter between the car radio harness and your car's electrical system by following the instructions provided with the adapter. This may require some wiring.

4. Configure the car radio

Once the adapter is installed, turn on the car radio and access the settings menu to enable and configure the steering wheel controls. You will be able to assign the desired functions to the buttons (volume, track change, etc.).

5. Test the controls

After configuration, test each steering wheel button to ensure it correctly controls the car radio.

By following these steps, you will be able to fully enjoy the steering wheel controls with your Pioneer MVH-X360BT, enhancing safety and comfort while driving.

Question 6

How to resolve a Bluetooth connection issue with the Pioneer DEH-1500UB car radio?

Accepted Answer

If you are unable to connect your Bluetooth device to the Pioneer DEH-1500UB car radio, here are several steps to follow to resolve this issue:

1. Check Bluetooth activation on the car radio

Make sure that the Bluetooth function of your car radio is activated. You can usually access this setting through the main menu or the device settings.

2. Put your device in discovery mode

Activate Bluetooth on your phone or other device and set it to visible or discovery mode so that the car radio can detect it.

3. Start searching for Bluetooth devices on the car radio

In the Bluetooth menu of the car radio, initiate a search for available devices. Your device should appear in the list of detected devices.

4. Pair the devices

When you select your device on the car radio, a pairing code may be requested. Enter it correctly. Default codes are often 0000 or 1234.

5. Check existing connections

Ensure that no other device is already connected to the car radio, as this may prevent a new Bluetooth connection.

6. Restart the devices

If the connection still fails, restart both the car radio and your Bluetooth device to reset the connections.

7. Update the car radio firmware

Finally, check if a firmware update is available for your Pioneer DEH-1500UB. An outdated version may cause Bluetooth connection issues.

By following these steps, you should be able to resolve most Bluetooth connection issues with your Pioneer DEH-1500UB car radio.

Question 7

What is the remote wire for on the PIONEER DEH-X7800DAB car radio and how to use it?

Accepted Answer

The remote wire (or remote control wire) on the PIONEER DEH-X7800DAB car radio is a control cable that sends an electrical signal when the device is powered on. This signal automatically activates connected external equipment, such as a power amplifier or the vehicle's automatic antenna relay.

Characteristics of the remote wire:

Color: Blue cable with a white stripe
Voltage and current: Delivers a voltage of 12 V DC with a maximum current of 300 mA
Main function: Sends a control signal when the car radio is turned on, and cuts this signal when it is turned off

Usage and connection: The remote wire of the DEH-X7800DAB should be connected to the remote turn-on terminal of an external power amplifier, or to the automatic antenna relay terminal of your vehicle. This allows the amplifier or antenna to be activated automatically at the same time as the car radio, without manual intervention.

The main advantage is automatic synchronization: when you turn on the car radio, the amplifier starts at the same time, and turns off when you switch off the device. This avoids having to manage the power supply of multiple devices separately and extends the lifespan of the equipment by properly deactivating them.

Important points: Ensure that the connection of the remote wire complies with the specifications of your external equipment (check the maximum supported voltage and required current). The wire should not be used to directly power equipment, but only to control its activation. Properly insulate the connections to avoid any short circuit, and feel free to consult your amplifier's manual for the exact color code of its remote control terminal.

Question 8

How to pair a Bluetooth device with the Pioneer MVH-X360BT car radio?

Accepted Answer

To pair a Bluetooth device with your Pioneer MVH-X360BT car radio, you need to access the connection menu and add the device via the ADD DEVICE function. Here are the detailed steps:

Before you start: Make sure Bluetooth is enabled on your smartphone or portable device and that it is visible and ready to be paired. Note that the car radio can accept up to 3 paired devices maximum.

Pairing procedure:

Access the connection menu: press and hold the car radio's menu button to display the Bluetooth connection menu.
Select ADD DEVICE: turn the M.C. knob to navigate to the ADD DEVICE option and press it.
Start the search: press M.C. to start searching for available Bluetooth devices. If you do not find your device, select RE-SEARCH to restart the search.
Select your device: turn M.C. to select your smartphone or device from the detected list, then press M.C.
Confirm pairing on your device: when prompted, check that the device name is Pioneer BT Unit and enter the default PIN code: 0000 (unless you have changed this code).
Validate the verification codes: a 6-digit number may appear on the car radio and your device. Ensure that both numbers match and confirm the pairing on your device. This number will disappear once the connection is established.

Important tips: If you cannot complete the connection from the car radio, use your device's Bluetooth menu to initiate the connection to the car radio. Do not attempt to pair during an ongoing call. If you already have 3 paired devices and need to add a new one, you will first need to delete an old device via the DEL DEVICE function in the connection menu. The default PIN code can be changed in the car radio settings if you wish to enhance security (access PIN CODE in the connection menu).

Once pairing is successful, a * symbol will appear next to your device name in the list of connected devices, confirming that the connection is established and active.

Question 9

How to set the time and date on the PIONEER AVIC-F320BT GPS car radio?

Accepted Answer

To set the time and date on your PIONEER AVIC-F320BT GPS car radio, access the regional settings that contain the time synchronization options.

Press [Home] from the map screen to open the main menu
Select [Settings] from the menu
Touch [Region] to open the regional settings
Touch [Time] to access the time settings

In the time settings screen, you can adjust the time zone by touching the [+] or [–] buttons. These buttons change the time in half-hour increments, with an adjustment range from -4 to +9 hours relative to the system's reference Central European Time. You also have additional options: Daylight Saving Time (to be activated if you are in the daylight saving time period) and Time Format (choice between 24-hour format, active by default, or 12-hour format with AM/PM).

Once you have made your adjustments, the car radio applies the changes. The system may restart to validate the new time settings. The settings will be retained even after the device is turned off and restarted.

User manual PIONEER Car stereo : user manuals and guides in PDF

Models PIONEER Car stereo most viewed

Other categories PIONEER

Recent questions about Car stereo PIONEER