Q: How to increase the brightness of the MVH-X380BT screen when the radio is off?

Unfortunately, the screen of the MVH-X380BT car radio completely turns off when you put the device in OFF mode . The lighting and brightness can only be adjusted when the device is powered on. To adjust the brightness, you must first turn the device on , then access the lighting menu: Press the M.C. knob to display the main menu Select [ILLUMINATION] Choose the [DIM SETTING] mode: either [SYNC CLOCK] (automatic adjustment based on the time) or [MANUAL] (manual adjustment) Set [BRIGHTNESS] from 1 to 10 according to your preference These lighting settings allow you to adjust the screen contrast according to the lighting conditions in your vehicle. However, when you turn off the device with the OFF button, the screen stops and no lighting is possible - there is no standby mode with active illumination on this model.

Q: How to turn off the Pioneer MVH-X380BT car radio and adjust the lighting?

To turn off the Pioneer MVH-X380BT car radio , press and hold the SRC/OFF button (for at least a few seconds) to power off the device. To control the lighting , access the ILLUMINATION Settings menu: DIM SETTING : Choose between two modes - [SYNC CLOCK] (the lighting automatically adjusts according to the time) or [MANUAL] (manual adjustment) BRIGHTNESS : Adjust the display intensity on a scale of 1 to 10 , depending on the chosen DIM SETTING mode To access these settings, press the M.C. knob to display the main menu, then navigate to ILLUMINATION .

Q: How to turn off the PIONEER MVH330DAB?

To turn off your PIONEER MVH330DAB, press and hold the SRC/OFF button for a few seconds until the device completely powers down. The SRC/OFF button is located on the control panel and is used to both turn the unit on and off. Note that when turning off, the device remembers your last selected source and audio settings (volume, equalizer, etc.), so they will be restored the next time you start it up.

Q: Where is the fuse of the PIONEER DEH-1300MP and what is its rating?

Yes, the PIONEER DEH-1300MP has a 10A fuse. This fuse is a critical component for the electrical protection of your car radio. In case of a power issue or if your device does not turn on, checking the fuse is one of the first troubleshooting steps: Check that the 10A fuse is not blown Replace it with a new fuse of the same rating (10A) if necessary Also, ensure that all power connections (yellow wire on permanent 12V, red wire on ignition) are tight Check that the battery voltage reaches at least 10.8V If the replacement fuse blows again immediately, this may indicate a more serious electrical problem in the installation or the device itself. In this case, contact a dealer or the authorized PIONEER service center.

Q: My PIONEER DEH-1300MP car radio won't turn on - what should I do?

First, check the power supply: Make sure the red wire (accessory) is properly connected to the ignition switch of your vehicle Check that the yellow wire (backup power) is connected to the permanent 12 V power supply Ensure that the black wire (ground) is securely attached to a bare metal part of the vehicle chassis, and not to a painted surface Next, try to turn the device on: Press the SRC/OFF button for a few seconds - the button should light up if the device is receiving power If the device still does not turn on: Check the 10 A fuse of the car radio - if it is blown, replace it with a fuse of the same amperage Check that your vehicle's battery is not discharged (the device requires at least 10.8 V for continuous operation) If none of these checks resolve the issue, contact an authorized Pioneer service center for professional diagnosis - there may be an internal problem requiring repair

Question 1

How to print the manual for the VREC-Z820DC?

Accepted Answer

If you did not receive the paper manual with your Pioneer VREC-Z820DC dashcam, you can download and print the PDF directly from this page.

Steps to print the manual:

Click on the PDF download link at the top of this page (available in French, English, or Spanish).
Once the file is downloaded, open it with your PDF reader (Adobe Reader, web browser, etc.).
Click on the Print icon (keyboard shortcut: Ctrl+P or Cmd+P on Mac) and confirm your print settings.
Select your printer and click on Print.

Note: if the document shows "temporarily unavailable" during your visit, it means that the PDF is being updated on our servers. Please try again a few minutes later, or contact our support for a direct copy of the VREC-Z820DC manual.

Question 2

How to increase the brightness of the MVH-X380BT screen when the radio is off?

Accepted Answer

Unfortunately, the screen of the MVH-X380BT car radio completely turns off when you put the device in OFF mode. The lighting and brightness can only be adjusted when the device is powered on.

To adjust the brightness, you must first turn the device on, then access the lighting menu:

Press the M.C. knob to display the main menu
Select [ILLUMINATION]
Choose the [DIM SETTING] mode: either [SYNC CLOCK] (automatic adjustment based on the time) or [MANUAL] (manual adjustment)
Set [BRIGHTNESS] from 1 to 10 according to your preference

These lighting settings allow you to adjust the screen contrast according to the lighting conditions in your vehicle. However, when you turn off the device with the OFF button, the screen stops and no lighting is possible - there is no standby mode with active illumination on this model.

Question 3

How to turn off the Pioneer MVH-X380BT car radio and adjust the lighting?

Accepted Answer

To turn off the Pioneer MVH-X380BT car radio, press and hold the SRC/OFF button (for at least a few seconds) to power off the device.

To control the lighting, access the ILLUMINATION Settings menu:

DIM SETTING: Choose between two modes - [SYNC CLOCK] (the lighting automatically adjusts according to the time) or [MANUAL] (manual adjustment)
BRIGHTNESS: Adjust the display intensity on a scale of 1 to 10, depending on the chosen DIM SETTING mode

To access these settings, press the M.C. knob to display the main menu, then navigate to ILLUMINATION.

Question 4

How to change the listening mode on the PIONEER VSX-528-S?

Accepted Answer

The PIONEER VSX-528-S has several dedicated buttons to change the listening mode directly on the front panel:

Using the front panel buttons

AUTO SURROUND/STREAM DIRECT - Press this button to toggle between automatic surround mode (which detects the source and applies the appropriate processing) and direct playback without processing (Stream Direct).
ALC/STANDARD SURR - Press this button to switch between Pro Logic II, NEO:6 modes and automatic level control (ALC) in stereo.
ADVANCED SURROUND - Use this button to cycle through the various advanced surround modes available depending on your audio source.

With each press, the listening mode changes and is displayed on the receiver's screen. The selected mode depends on your audio source (movie, music, radio, etc.).

Access via the remote control

You can also access advanced audio settings by pressing the RECEIVER button followed by AUDIO PARAMETER on the remote control to fine-tune your listening settings.

For more details on each listening mode, refer to pages 37-39 of the manual provided above.

Question 5

The indicator light on my Pioneer PDP-506 television does not change color and remains stuck - how do I start the device?

Accepted Answer

If the indicator light on your Pioneer PDP-506 PE or PDP-506FDE television remains stuck and does not alternate between red (standby) and blue (on), this indicates a malfunction of the device. Normally:

The red light turns on when the device is in standby mode
The blue light turns on when you press POWER to fully power on the device

If the light refuses to change state, here are the troubleshooting steps:

Check that the power cord is properly plugged into a functioning wall outlet
Completely unplug the device for 30 seconds, then plug it back in - this may reset the system
Try pressing the POWER button located on the front of the plasma screen several times
Also try using the remote control, pressing the button (①) or the numbers 0-9
Check that no button is stuck or blocked on the media receiver (STANDBY/ON button)

If after these steps the light remains stuck and the device still does not start, there is likely an internal electronic problem requiring professional repair. In this case, contact an authorized Pioneer service center.

Question 6

How to turn off the PIONEER MVH330DAB?

Accepted Answer

To turn off your PIONEER MVH330DAB, press and hold the SRC/OFF button for a few seconds until the device completely powers down. The SRC/OFF button is located on the control panel and is used to both turn the unit on and off.

Note that when turning off, the device remembers your last selected source and audio settings (volume, equalizer, etc.), so they will be restored the next time you start it up.

Question 7

Where is the fuse of the PIONEER DEH-1300MP and what is its rating?

Accepted Answer

Yes, the PIONEER DEH-1300MP has a 10A fuse. This fuse is a critical component for the electrical protection of your car radio.

In case of a power issue or if your device does not turn on, checking the fuse is one of the first troubleshooting steps:

Check that the 10A fuse is not blown
Replace it with a new fuse of the same rating (10A) if necessary
Also, ensure that all power connections (yellow wire on permanent 12V, red wire on ignition) are tight
Check that the battery voltage reaches at least 10.8V

If the replacement fuse blows again immediately, this may indicate a more serious electrical problem in the installation or the device itself. In this case, contact a dealer or the authorized PIONEER service center.

Question 8

My PIONEER DEH-1300MP car radio won't turn on - what should I do?

Accepted Answer

First, check the power supply:

Make sure the red wire (accessory) is properly connected to the ignition switch of your vehicle
Check that the yellow wire (backup power) is connected to the permanent 12 V power supply
Ensure that the black wire (ground) is securely attached to a bare metal part of the vehicle chassis, and not to a painted surface

Next, try to turn the device on:

Press the SRC/OFF button for a few seconds - the button should light up if the device is receiving power

If the device still does not turn on:

Check the 10 A fuse of the car radio - if it is blown, replace it with a fuse of the same amperage
Check that your vehicle's battery is not discharged (the device requires at least 10.8 V for continuous operation)
If none of these checks resolve the issue, contact an authorized Pioneer service center for professional diagnosis - there may be an internal problem requiring repair

Question 9

How do I disable the message 'This function is not available while driving'?

Accepted Answer

This message is an intentional safety system and cannot be disabled.

Your DMH-130BT has a parking brake interlock device that automatically disables certain functions (such as video display and some operations of the touch keyboard) while the vehicle is in motion. This is a legally mandated safety measure to prevent driver distraction.

The manual explicitly states: 'Do not do anything to tamper with or disable the parking brake interlock device.'

To access restricted functions

Engage the parking brake
Release the parking brake
Re-engage the parking brake

Once this sequence is performed while stopped, the restricted functions will be temporarily available again.

Question 10

How do I connect my phone via Bluetooth and listen to music on the PIONEER MVH330DAB?

Accepted Answer

Step 1: Pair your phone

For the first use, you need to pair your phone with the PIONEER MVH330DAB car radio. Turn on Bluetooth on your phone, then press the phone button on the radio to display the menu. Turn the M.C. knob to select [REGLA.BT] and press to confirm. Then select [AJOUTAPP] to start searching for available devices. The car radio will display a list of nearby Bluetooth devices.

In this list, turn the M.C. knob to select your phone, then press to confirm. A 6-digit PIN code will appear on the car radio screen. If your phone asks for a PIN code during pairing, enter 0000. Complete the pairing operation on both devices to finalize the connection.

Step 2: Access the Bluetooth audio source

Once paired, press the SRC/OFF button (source button) several times to select [BT AUDIO] from the available sources. Music playback will start automatically. Use the M.C. knob to adjust the volume to your liking.

Available playback controls

Press the 4 button to pause or resume playback
Press the arrows to navigate between tracks (depending on your device's compatibility)
Press the 5 button to activate random playback
Press the 6 button to activate repeat playback

Important points to remember

Only one device can be paired at a time. If you want to add a new device, you must first disconnect the old one in the [JUMEL.BT] menu
The PIONEER MVH330DAB supports A2DP Bluetooth profiles (for music) and AVRCP (for playback controls)
The sound from Bluetooth audio is automatically interrupted when a phone call comes in
Do not leave the device in standby for Bluetooth connection when the engine is off, as this may drain the vehicle's battery

User manual PIONEER : user manuals and guides in PDF

Models PIONEER most viewed

Browse manuals PIONEER by appliance type

Recent questions about devices PIONEER