JetStream T2600G-52TS - Network switch TP-LINK - Free user manual and instructions

Product type	Managed network switch
Model	JetStream T2600G-52TS
Brand	TP-Link
Number of ports	52 ports (48 RJ45 10/100/1000 Mbps ports + 4 SFP slots)
Power supply	AC 100-240V, 50-60Hz
Dimensions (W x D x H)	440 x 220 x 44 mm (19-inch rack mount, 1U)
Weight	Approximately 3.5 kg
Main functions	L2/L3 switching, VLAN, QoS, IGMP Snooping, ACL, STP, link aggregation, Web and CLI management
Management	Web interface, Console (CLI), SNMP, RMON
Mounting	On desktop or 19-inch rack (brackets included)
Connectivity	RJ45 ports, SFP ports, RS232 console port
Security	ACL, 802.1X, RADIUS, TACACS+, Storm Control, DHCP Snooping
Operating temperature	0°C to 40°C
Operating humidity	10% to 90% RH (non-condensing)
Maintenance and cleaning	Unplug before cleaning. Use a dry, soft cloth. Do not use liquid or abrasive products.
Spare parts and repairability	The switch contains no user-serviceable parts. Contact customer support for any repairs.
Warranty	TP-Link limited warranty (duration varies by country, see packaging)

Frequently Asked Questions - JetStream T2600G-52TS TP-LINK

How to access the switch's management interface?

First set your computer's IP address in the same subnet as the switch (default 192.168.0.x). Open a browser and enter http://192.168.0.1. Use the default username and password admin (lowercase).

How to reset the switch to factory settings?

Press and hold the Reset button on the front of the switch for about 10 seconds until the system LED blinks. Release the button. The factory configuration will be restored.

What is the default IP address of the switch?

The default IP address is 192.168.0.1 with subnet mask 255.255.255.0. The web interface is accessible via this address.

How to connect an SFP module?

Gently insert the SFP module into the dedicated slot until it clicks. To remove it, pull the release lever. Ensure the module is compatible with the switch.

What to do if the switch does not power on?

Check that the power cord is properly connected to the switch and a working power outlet. Try another power cord if possible. If the problem persists, contact TP-Link support.

How to configure a VLAN on the switch?

Log in to the web interface. Go to VLAN then 802.1Q VLAN. Create a new VLAN and assign the desired ports. Remember to set the VLAN ID and configure the ports as tagged or untagged according to your needs.

Does the switch support Quality of Service (QoS)?

Yes, the T2600G-52TS supports QoS based on Class of Service (CoS) and DSCP priorities. You can configure queues and scheduling in the web interface under QoS.

How to rack-mount the switch?

Attach the included mounting brackets to each side of the switch using the included screws. Position the switch in the rack and screw the brackets to the rack with appropriate bolts (not included).
Ensure the rack is stable and grounded.

What types of cables to use with this switch?

Use Category 5e or 6 Ethernet cables for RJ45 ports. For SFP ports, use compatible SFP modules with single-mode or multi-mode fiber depending on distance.

How to update the firmware?

Download the latest firmware from the TP-Link website. Log in to the web interface, go to System > Firmware Upgrade. Select the downloaded file and click Upgrade. Do not power off during the update.

USER MANUAL JetStream T2600G-52TS TP-LINK

Easy Smart&Smart&Managed Rackmount Switch

CONTENTS

Deutsch....01

English....06

Español....11

Ελληνικά....16

Français....21

Italiano....26

Português....31

Suomi....36

Nederlands....41

Svenska....46

Norsk....51

Dansk....56

Türkçe....61

Installation

- Tischmontage

- SFP-Port

- Einschalten

Konfiguration

- Desktop Installation

To install the device on the desktop, please follow the steps below:

1. Set the device on a flat surface strong enough to support the entire weight of the device with all fittings.
2. Remove the adhesive backing papers from the rubber feet.
3. Turnover the device and attach the supplied rubber feet to the recessed areas on the bottom at each corner of the device.

- Rack Installation

To install the device in a rack, follow the instructions described below:

1. Check the grounding and stability of the rack.
2. Secure the supplied rack-mounting brackets to each side of the device with supplied screws.

1. After the brackets are attached to the device, use suitable screws (not provided) to secure the brackets to the rack.

Connection

- Ethernet Port

Connect an Ethernet port of the switch to the computer by RJ45 cable as the following figure shown.

- SFP Port

For switches with SFP ports, you can connect a SFP port to a SFP module. If an SFP transceiver is installed in a slot and has a valid link on the port, the associated RJ45 port will be disabled and cannot be used.

- Console Port

For switches with the console port, you can connect the console port with your computer by the console cable. Then you can load the CLI to manage the switch.

- Power On

Plug the female connector of the provided power cord into the power socket of the device, and the male connector into a power outlet.

Configuration

- Configure the Switch Using the GUI

1. Set the IP address of your PC in the same subnet of the switch. The IP address is 192.168.0.x("x" is any number from 2 to 254); the Subnet Mask is 255.255.255.0.
2. Open a web browser and type the default management address http://192.168.0.1 in the address field of the browser, then press the Enter key.
3. Enter admin for the default User Name and Password, both in lower case letters. Then click the Login button or press the Enter key.
4. After a successful login, you can configure the switch on the management page.

- Configure the Switch Using the CLI (Only for Smart Switches and Managed Switches)

You can log on to the switch and access the CLI to manage the switch. For the detailed instructions as to how to do this, please refer to the CLI Guide.

- Configure the Switch Using the Utility (Only for Easy Smart Switches)

You can use the Easy Smart Configuration Utility to centrally manage entire networks of the Easy Smart Switches. For the detailed instructions as to how to do this, please refer to the Utility User Guide.

Instalación

- Puerto SFP

- Encender

Configuración

- Θύρα SFP

- Θúpa Console

- Ενεργοποιήστε

Ρύθμιση

Configuration

- Configurer le switch via son interface graphique

- Accensione

Configurazione

- Ligar

Configuração

- Configurar o Switch via Interface gráfica

- Virta päällä

Konfigurointi

- Konfiguroi kytkin GUI:lla

- Inschakelen

Configuratie

- Desktop-installation

Anslutning

- Ethernet-port

- Ström på

Konfiguration

- For å slå på

Konfigurasjon

- Tændt

Konfiguration

- Cihazı Çalıştırma

Yapılandırma

• When a product has a power on/off button, the power on/off button is one way to turn-off the product. For products without the on/off button, the only way to completely turn-off the product is to disconnect the product or the power adapter from the power source. The disconnected device shall remain readily operable.
• Do not open this product or attempt to service it; it may expose you to dangerous high voltage or other risks. Opening a sealed component or sealed product/s will void the warranty. For product servicing, please contact us.
• Do not operate this product near water.

TP-LINK Limited Product Warranty

For TP-LINK Branded Products Only.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE (OR BY COUNTRY OR PROVINCE).

TO THE EXTENT ALLOWED BY LOCAL LAW, THIS WARRANTY AND THE REMEDIES SET FORTH ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS.

TP-LINK warrants the TP-LINK branded hardware product contained in the original packaging against defects in materials and workmanship when used normally in according with TP-LINK's guidelines for some period which depends on the local service from the date of original retail purchase by the end-user purchaser.

Español

South Building(floors 1,3,4,5) and 28(floors 1-4), Central Science & Technology Park, Shennan Rd, Nanshan, Shenzhen, China

Robert-Bosch-Straße 9, 65719 Hofheim am Taunus, Germany

Unit 2 & 3 Riverview (142-144), Cardiff Road, Reading, RG1 8EW

Marathonodromou 77, Marousi 151 24, Greece

Specifications are subject to change without notice. TP-LINK is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2016 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.