MS-H-ProA - Magnetic stirrer Vevor - Free user manual and instructions

Product type	Magnetic hotplate stirrer
Brand	Vevor
Model	MS-H-ProA
Product dimensions (L x W x H)	280 x 160 x 510 mm
Package dimensions (L x W x H)	332 x 220 x 200 mm
Net weight	3.28 kg
Gross weight	3.7 kg
Input voltage	120/200~240 VAC
Frequency	50/60 Hz
Power	650 W
Max stirring capacity	20 L
Stirring speed range	100 - 1500 rpm
Max heating temperature	340 °C
Display	LCD screen
Functions	Stirring, heating, external PT1000 probe, RS232 remote control
Safety	Residual heat warning (Hot), dual safety circuit
Maintenance	Disconnect before cleaning; use isopropyl alcohol or surfactant water
Intended use	Mixing and/or heating liquids in laboratory, school, factory
Warranty	Check the electronic support and warranty certificate at vevor.com/support

Frequently Asked Questions - MS-H-ProA Vevor

How to use the external PT1000 temperature probe?

Plug the PT1000 probe into the designated socket. The LCD screen then displays 'Sonde'. Set the desired temperature with the heating knob. The external probe allows more precise control of the medium temperature.

What to do if error code ER9 is displayed?

Error ER9 indicates that the set temperature is insufficient or the probe is not placed correctly. Check that the set temperature exceeds the initial displayed temperature by at least 10 °C and that the initial temperature is below 35 °C. Ensure the temperature rises by at least 2 °C after 7 minutes of heating.

How to clean the MS-H-ProA magnetic stirrer?

Disconnect the device before any cleaning. Use a soft cloth moistened with isopropyl alcohol or water containing a surfactant. Never spray liquid directly onto the device.

What is the stirring speed range?

The stirring speed can be adjusted from 100 to 1500 rpm in increments of 10 rpm using the stirring knob.

Can I control the device remotely?

Yes, the device is equipped with an RS232C interface allowing connection to a PC. Use dedicated software for remote control. The LCD screen displays 'Remote' when the function is active.

How does the residual heat warning work?

After turning off the heating, if the hotplate exceeds 50 °C, the LCD screen displays a flashing 'Hot'. This warning turns off automatically when the temperature drops below 50 °C.

What to do if the device does not turn on?

Check that the power cord is properly plugged in and the outlet is powered. Also check the fuse condition: if it is broken or loose, replace it.

What is the maximum stirring capacity?

The maximum stirring capacity is 20 liters of water. For more viscous liquids, the speed may be reduced.

How to set the heating temperature?

Slowly turn the heating knob to the desired temperature. The set temperature is displayed on the right side of the LCD screen. Press the heating knob to activate the function.

Can I use the device without the heating function?

Yes, the stirring function is independent. You can use only stirring without activating heating.

USER MANUAL MS-H-ProA Vevor

Technical Support and E-Warranty Certificate https://www.vevor.com/support

MAGNETIC STIRRERS

USER MANUAL

MODEL NO.: MS-S, MS-H-ProA

We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are actually saving half in comparison with the top major brands

VEVOR®

TOUGH TOOLS, HALF PRICE

Magnetic Stirrers

MODEL NO.: MS-S, MS-H-ProA

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of o user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you ag there are any technology or software updates on our product.

WARNING:

Please read this manual carefully before using the product. Failure do so may result in serious injury. SAVE THIS MANUAL

	Warning!● Read the operating instructions carefully before use.● Ensure that only trained staff works with the instru
	Risk of burn!● Caution when touch the housing parts and the hotwhich can reach temperature of exceed 300 °C.● Pay attention to the residual heat after switching of
	Protective ground contact!● Make sure that socket must be grounded (protectivecontact) before use.

• When operating, wear personal safety protection to avoid the risk of
• Splashing and evaporation of liquids
• Release of toxic or combustible gases
• Set up the instrument in a spacious area on a stable, clean, non-slip, and fireproof surface. Do not operate the instrument in explosive atmospheres, with hazardous substances, or around water. Gradually increase the speed, and reduce the speed if:
• The stirring bar breaks away due to high speed
• The instrument is not running smoothly, or the container is not centered on the plate
• Temperature must always be set to at least 50°C lower than the flash point of the media used.
• Be aware of hazards due to:
• Flammable materials or media with a low boiling temperature
• Overfilling of media
• Unsafe container

- Process pathogenic materials only in closed vessels.

- If the case of the stirrer bar is PTFE, please note:

- Elemental fluorine, fluorine trifluoride, and alkali metals will corrode PTFE, and halogenated alkanes will cause it to swell at room temperature.

- Molten alkali metals, alkaline earth metals, or their solutions, as well as powders of elements from the second and third groups of the Periodic Table, will react chemically with PTFE when the temperature reaches 300–400°C.

- Check the instrument and accessories prior to each use. Do not use damaged components. Safe operation is only guaranteed with the accessories listed in the “Accessories” section. Accessories must be securely attached to the device and must be removed when not in use. Always disconnect the power before fitting accessories.

- When an external temperature sensor is needed, the tip of the measuring sensor must be at least 5–10 mm from the vessel bottom wall.

- The instrument can only be fully disconnected from the main power supply by turning off the main switch or disconnecting the plug.

- The voltage stated on the label must correspond to the main power supply.

- Ensure that the main power supply cable does not touch the hotplate. Do not cover the device.

● The instrument must only be operated by experts.

Keep away from high magnetic fields.

SAVE THIS MANUAL

Proper use

The instrument is designed for mixing and/or heating liquids in schools, laboratories or factories.

Observe the minimum distances between multiple units, and the distance to the rear wall and above the assembly (min. 100 mm).

Figure 1

This device is not suitable for use in residential areas or other locations mentioned in the Safety Instructions.

TECHNICAL SPECIFICATIONS

Model MS-S	MS-H-ProA
Voltage [VAC] 120/200~240 120/200~240
Frequency [Hz] 50/60 50/60
Power [W] 30	650
Maximum stirring capacity [L]	20L 20L
Maximum heating temperature [°C]	/ 340
Product Dimensions (L*W*H) [mm]	280*160*90	280*160*510
Packing Size (L*W*H) [mm]	332*220*155	390*215*200
Net Weight [kg]	2.35	3.28
Gross Weight [kg]	2.75 3.7

Products such as specifications, appearance, and design are subject to modification without prior notice.

PACKAGE CONTENTS

MS-S

Machine*1

Fuse*1

Stirrer bar*1

Power cord*1 (Plugs vary from export area to export area)

MS-H-ProA

Machine*1

Fuse*1

Stirrer bar*1

Power cord*1 (Plugs vary from export area to export area)

protective cover*1

support*1

Temperature probe*1

PRODUCT FUNCTIONS

Power Switch

Model	Items	Descriptions
MS-S	Stirring knob Stir	Set the rated rotary speed in the safe stirrin range from 0 to 1500 rpm. The function “Stir is switched ON or OFF via the knob.
	LED Stir	When the stirring function is switched ON, the LED Stir is lit.
	Power switch	Switch ON or OFF.
MS-H-ProA	Stirring knob S	Set the rated rotary speed. The function “Stir is switched ON or OFF via push ON/OFF th
	Heating knob He (Hotplate model)	Set the rated temperature. The function “heati is switched ON or OFF via push ON/OFF th Set the heating mode. startup and during the initialization, rotate the Heat knob, select amo the mode A/B/C.
	LCD	LCD displays the real working state and all settings.
	Heating indicator light (Hotplate model)	When the heating function is switched ON, th Heating indicator light is lit.
	stirring indicator light	When the stirring function is switched ON, th stirring indicator light is lit.
	Power Switch	Switch ON or OFF the instrument.

Display(MS-H-ProA)

Characters	Descriptions
Temp &	Display temperature when the heating function is switched (
Stir	Display stirring state when the stirring function is switched
Hot	Displays HOT warning if the plate temperature is above 50 switching OFF the heating function.
Probe	Display when using external probe.
Remote	Display in case of remote control.
Err	Display in case of error happening.
Rated value /Real value	Display value in case of heating or stirring function switchin
A	rapid heating mode, under which the heating speed is the but there may be some overshoot
B	standard heating mode, under which the heating speed is and the overshoot is smaller
C	steady heating mode, under which the heating speed is sl but the overshoot is small or no overshootNote:If both heating and stirring functions have been started at the san heat display always has higher priority. If in this case speed is c via the stirring knob, it displays stirring speed and reverts to temp after 5 seconds.Heating mode Setting method: startup and during the initialization, the Heat knob, select among the mode A/B/C. The mode will be automatically locked after 3 seconds. If you need to adjust again, repeat the same setting operation after restarting the machine

Trial run ● Make sure the required operating voltage and power supply voltage match. - Ensure the socket must be properly grounded. - Plug in the power cable, ensure the power is on and begin initializing. - Add the medium into the vessel with an appropriate stirring bar. - Place vessel on the work plate. - Set the target stirring speed and begin. - Observe the stirring bar and LCD display (digital model). - Set the target temperature and start heating. - Observe the real temperature on LCD display (digital model). - Stop the heating and stirring functions.

● Make sure the required operating voltage and power supply voltage match. - Ensure the socket must be properly grounded. - Plug in the power cable, ensure the power is on and begin initializing. - Add the medium into the vessel with an appropriate stirring bar. - Place vessel on the work plate. - Set the target stirring speed and begin. - Observe the stirring bar and LCD display (digital model). - Set the target temperature and start heating. - Observe the real temperature on LCD display (digital model). - Stop the heating and stirring functions.

If the operations above are normal, the device is ready to open. If they are not normal, the device may have been damaged during transportation. In that case, please contact the manufacturer or supplier for technical support.

Forbid to transfer the vessel when the instrument working.

Forbid to transfer the vessel when the instrument is working.

The device is controlled by digital temperature control technology which has two separate safe circuits. The hotplate is kept at a constant temperature by a digital control circuit. The hotplate temperature can also be monitored from a separate, adjustable safety circuit. The two temperature sensors (PT 1000) internal for temperature control are built into the hotplate. The single external PT 1000 can monitor the temperature of sample.

The device is controlled by digital temperature control technology, which features two separate safety circuits. The hotplate is maintained at a constant temperature by a digital control circuit. Additionally, the hotplate temperature can be monitored via a separate, adjustable safety circuit. The two internal temperature sensors (PT 1000) for temperature control are built into the hotplate. A single external PT 1000 can monitor the temperature of the sample.

• Plug in the external PT1000.
• Set the temperature by rotating the temperature control knob

slowly to the target value.

• When the heating function is switched on, the LED “Heat” will light up and the LCD will display the real temperature.
• The rated temperature will be displayed on the right-hand side of the LCD, along with characters.
• The heating function is switched on or off by pushing the heating knob.

The instrument is turned on for the setting zone temperature setting with the last shutdown temperature. In the common case, setting the heating temperature displays the actual temperature may have the following differences:

• Hotplate center and outer edge.
• The sample container and the container.

In order to ensure the accuracy of the temperature inside the container, please use the external temperature sensor PT1000.

Working with external temperature sensor

The external temperature sensor PT1000 is the manufacturer's standard accessory. If the sensor is plugged in, “Probe” will be shown on the digital display to indicate the sensor is operating. The setting value of the external temperature sensor and the actual temperature are displayed. A safe circuit controls the hotplate temperature.

Compared with the temperature control of the hotplate, the external temperature sensor can control the medium's temperature more

precisely.

Residual heat warning (HOT)

In order to prevent the risk of burns from a hotplate, the digital hotplate has a residual heat warning function. When the heating function is switched off and the heating plate temperature is still above 50°C, "Hot" will flash to warn that there is a hazard of burns from the hotplate. When the hotplate temperature drops to below 50°C, the unit will automatically switch off. If users want to turn off the unit immediately, just pull out the plug directly. When the plug is pulled out, the residual heat warning function cannot be run.

Stirring (MS-H-ProA)

The function "stirring" is switched on or off by rotating the stirring knob. The speed is set on the knob (100 to 1500 rpm in steps of 10 rpm). When both the heating and stirring functions are switched on and the above operations are done, the LCD will shift to the speed value and come back to the temperature value in about 5 seconds.

Remote Control (MS-H-ProA)

The unit can be controlled from an external PC (using the dedicated software) via the RS232C serial interface fitted to the unit. Data communication from laboratory instrument to computer is only possible on demand of the computer.

• The functions of the interface lines between laboratory instrument and automation system are selected from the specified signals of the EIA-standard RS232C, corresponding with DIN66020 Part 1. The allotment of the bushing can be seen in Figure 7. ● Transmission method: Asynchronous signal transmission in start-stop operation.
• Mode of transmission: Full Duplex. 1 start bit; 7 character bits; 1 parity bit (even); 1 stop bit. ● Transmission speed: 9600 bit/s.
• Start remote control knob, LCD display "Remote".

Note:

Forbid to insert or remove the RS232C communication line when switch on!

Faults

- Instruments can't be powered ON

• Check whether the power line is unplugged
• Check whether the fuse is broken or loose

● Fault in power ON self-test

- Switch OFF the unit, then switch ON and reset the instruments to factory default setting.

- Stir speed cannot reach set point

- Excessive medium viscosity may cause abnormal speed reduction of the motor

- Unit cannot be powered off when switched off.

- Check if the residual heat warning function is still ON and hotplate temperature is above 50°C (the LED screen still works and “Hot” flashes).

- Fault error

(Applicable to machine models: MS-H-ProA)

Describe& conditions	code	conditions
The temperature sensor is incorrectly placed or not put into the container during heating.The temperature rises less than 2 °C after 7 minutes of heating.	ER9	1. The setting temperature shall be more than the initial temperature displayed on the screen +10°C2. The initial temperature displayed on the screen shall be less than 35°C . 3. The temperature shall rise within 2°C after heating for 7min.
When the temperature senso is taken out of the containe during heating, the temperature measured value drops by more than 1°C eve 3 seconds	ER3	The time of PT1000 sensor in liquid is than 1min
During the heating process, PT1000 detection temperature exceeds the target temperature by 40°C.	ER4	Set the target temperature to be higher the initial temperature

If these faults are not resolved, please contact dealer/supplier.

Maintenance and Cleaning

● Proper maintenance can keep instruments working properly and lengthen their lifetime. - Do not spray cleanser into the instrument when cleaning. ● Unplug the power line when cleaning. ● Only use recommended cleansers:

● Dyes	● Isopropyl alcohol
● Construction materials	● Water containing tenside /Isopropyl alcohol
● Cosmetics	● Water containing tenside /Isopropyl alcohol
● Foodstuffs	● Water containing tenside
● Fuels	● Water containing tenside

• Before using other method for cleaning or decontamination, the user must ascertain with the manufacturer that this method will not harm the instrument. Wear the proper protective gloves during cleaning of the instrument.

Note:

● Electronic devices cannot be cleaned with cleanser. - If you require maintenance service, must be cleaned the instrument in advance to avoid pollution of hazardous substances, and sent back into its original packing. - If the instrument will not be used for a long time, please switch it off and place it in a dry, clean, no temperature, and stable location.

This product is subject to the provision of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste, but must be taken to a collection point for recycling electrical and electronic devices.

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, Baoshan District, Shanghai 200000, CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREET, EASTWOOD NSW 2122, Australia.

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho

Cucamonga, CA 91730

REPE

E-CrossStu GmbH

Mainzer Landstr.69, 60329

Frankfurt am Main.

REPU

YH CONSULTING LIMITED.

K/O YH Consulting Limited Office 147, Centurion

House, London Road, Staines-upon-Thames,

Surrey, TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

Technical Support and E-Warranty Certificate

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

We continue to be committed to providing you tools with competitive prices. "Save Half", "Half Price" or any other similar expressions used by us only represent the savings you might benefit from buying certain tools with us compared to top brands and do not necessarily mean that all categories of tools offered are covered. We kindly remind you to verify carefully when placing an order with us to ensure you are actually saving half in comparison with the top major brands.

VEVOR®

TOUGH TOOLS, HALF PRICE

Magnetic Stirrers

MODEL NUMBER: MS-S, MS-H-ProA

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of the user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you of any technology or software updates on our product.

WARNING:

Figure 1

Machine*1

Fuse*1

Stirrer bar*1

Power cord*1 (Plugs vary from export area to export area)

MS-H-ProA

Machine*1

Fuse*1

Stirrer bar*1

Power cord*1 (Plugs vary from export area to export area)

protective cover*1

support*1

Temperature probe*1

PRODUCT FUNCTIONS

MS-H-ProA

Power Switch

C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

We continue to be committed to providing you with tools at competitive prices. "Save Half", "Half Price" or any other similar expressions used by us only represent the savings you might benefit from buying certain tools with us compared to top brands and do not necessarily mean to cover all categories of tools offered. We kindly remind you to verify carefully when placing an order with us to ensure you are actually saving half in comparison with the top major brands.

VEVOR®

TOUGH TOOLS, HALF PRICE

Magnetic Stirrers

MODEL NUMBER: MS-S, MS-H-ProA

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of the user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you if there are any technology or software updates on our product.

WARNING:

Figure 1

Machine*1

Fuse*1

Stirrer bar*1

Power cord*1 (Plugs vary from export area to export area) MS-H-ProA

Machine*1

Fuse*1

Stirrer bar*1

Power cord*1 (Plugs vary from export area to export area)

protective cover*1

support*1

Temperature probe*1

MS-H-ProA

Power Switch

Imported in AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Imported in USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

EC

REP

E-CrossStu GmbH

Mainzer Landstr.69, 60329 Frankfurt am Main

UK

REP

YH CONSULTING LIMITED.

C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represent of savings you might benefit from buying certain tools with us compared top brands and does not necessarily mean to cover all categories of tools offered are kindly reminded to verify carefully when you are placing an order with us actually saving half in comparison with the top major brands.

VEVOR®

TOUGH TOOLS, HALF PRICE

Magnetic Stirrers

MODELL NR.: MS-S, MS-H-ProA

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of user manual. The appearance of the product shall be subject to product you received. Please forgive us that we won't inform your use, there are any technology or software updates on our product.

WARNING:

Figure 1

Machine*1

Fuse*1

Stirrer bar*1

Power cord*1 (Plugs vary from export area to export area)

MS-H-ProA

Machine*1

Fuse*1

Stirrer bar*1

Power cord*1 (Plugs vary from export area to export area)

PRODUCT FUNCTIONS

MS-H-ProA

Power Switch

C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

We continue to be committed to providing you with tools at competitive prices. "Save Half", "Half Price", or any other similar expressions used by us only represent the savings you might benefit from buying certain tools with us compared to top brands and do not necessarily mean that all categories of tools offered are covered. We kindly remind you to verify carefully when placing an order with us to ensure you are actually saving half in comparison with the top major brands.

VEVOR®

TOUGH TOOLS, HALF PRICE

Magnetic Stirrers

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of the user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you of any technology or software updates on our product.

WARNING:

Figure 1

Machine*1

Fuse*1

Stirrer bar*1

Power cord*1 (Plugs vary from export area to export area) MS-H-ProA

Machine*1

Fuse*1

Stirrer bar*1

Power cord*1 (Plugs vary from export area to export area)

protective cover*1

support*1

Temperature probe*1

PRODUCT FUNCTIONS

MS-H-ProA

Power Switch

Anaheim Place, Rancho Cucamonga, CA 91730

EC

REP

E-CrossStu GmbH

Mainzer Landstr.69, 60329 Frankfurt am Main

UK

REP

YH CONSULTING LIMITED.

C/O YH Consulting Limited Office 147, Centurion

House, London Road, Staines-upon-Thames, Surrey

TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

Technical Support and E-warranty Certificate https://www.vevor.com/support

We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represent estimate of savings you might benefit from buying certain tools with us compared to top brands and does not necessarily mean to cover all categories of tools offered. We kindly remind you to verify carefully when you are placing an order with us that you are actually saving half in comparison with the top major brands.

VEVOR®

TOUGH TOOLS, HALF PRICE

Magnetic Stirrers

MODEL NUMBER: MS-S, MS-H-ProA

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction, please read all manual instruction carefully before operating. VEVOR reserves a clear interpretation user manual. The appearance of the product shall be subject to product you received. Please forgive us that we won't inform you there are any technology or software updates on our product.

WARNING:

Figure 1

Machine*1

Fuse*1

Stirrer bar*1

Power cord*1 (Plugs vary from export area to export area)

MS-H-ProA

Machine*1

Fuse*1

Stirrer bar*1

Power cord*1 (Plugs vary from export area to export area)

PRODUCT FEATURES

MS-H-ProA

Power Switch

C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

Technical Support and E-warranty Certificate www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

We continue to be committed to providing you with tools at competitive prices. "Save Half", "Half Price", or any other similar expressions used by us only represent the savings you might benefit from buying certain tools with us compared to top brands and do not necessarily mean that all categories of tools offered are covered. We kindly remind you to verify carefully when placing an order with us to ensure you are actually saving half in comparison with the top major brands.

VEVOR®

TOUGH TOOLS, HALF PRICE

Magnetic Stirrers

MODEL NO: MS-S, MS-H-ProA

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of the user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you of any technology or software updates on our product.

WARNING:

Image 1

Machine*1

Fuse*1

Stirrer bar*1

Power cord*1 (Plugs vary from export area to export area)

MS-H-ProA

Machine*1

Fuse*1

Stirrer bar*1

Power cord*1 (Plugs vary from export area to export area)

Protective cover*1

Support*1

Temperature probe*1

PRODUCT FEATURES

Stirring (MS-H-ProA)

C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represent of savings you might benefit from buying certain tools with us compared top brands and does not necessarily mean to cover all categories of tools offered are kindly reminded to verify carefully when you are placing an order with us actually saving half in comparison with the top major brands.

VEVOR®

TOUGH TOOLS, HALF PRICE

Magnetic Stirrers

MODEL NO.: MS-S, MS-H-ProA

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of the user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you if there are any technology or software updates on our product.

WARNING:

Figure 1

Machine*1

Fuse*1

Stirrer bar*1

Power cord*1 (Plugs vary from export area to export area)

MS-H-ProA

Machine*1

Fuse*1

Stirrer bar*1

Power cord*1 (Plugs vary from export area to export area)

protective cover*1

support*1

Temperature probe*1

PRODUCT FUNCTIONS

MS-H-ProA

Power Switch

STREET EASTWOOD NSW 2122 Australia

Imported into the USA: Sanven Technology Ltd. Suite 250, 9166 Anar Place, Rancho Cucamonga, CA 91730

EC

REP

E-CrossStu GmbH

Mainzer Landstr.69, 60329 Frankfurt am Main

UK

REP

YH CONSULTING LIMITED.

C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey TW18 4AX

VEVOR®

TOUGH TOOLS, HALF PRICE