GTC 40-305 - Grass trimmer ATIKA - Free user manual and instructions

USER MANUAL GTC 40-305 ATIKA

Original instructions

Notice originale

① Keep the instructions in a safe place for future use.
① Pass the operating instructions on to all persons who work with the machine.

Do not operate machine before having read the operating instructions, understood all the notes and assembly the machine as described here.

This machine must not be operated / used by children, persons with restricted physical, sensory or mental abilities or a lack of experience and/or know-how or by persons who are not familiar with the instructions.

The machine and charging unit must not be operated by children or young people under 16 years of age.

National and local regulations may determine a different age restriction for the user.

Keep children away from the battery since they cannot estimate the hazards of the battery.

Contents

Extent of delivery	14
Operating times	14
EC Declaration of Conformity	15
Symbols original instructions	15
Symbols on the machine	15
Proper use	16
Residual risks	16
Hand-Arm-Vibrations	16
Safety instructions	17
- Personal protective equipment	17
- Safety instructions -before working	17
- Safety instructions -operating	17
- Safety instructions -while working	17
- General safety instructions	18
- Behaviour in an emergency situation	18
Description of device / spare parts	18
Assembly	19
- Attaching the protective hood	19
- Attaching the handle	19
- Connecting upper- and lower part	19
- Choosing cutting diameter	19
Before the first start-up	19

Start-up	19
– Switching On / Off	19
– Energy-saving mode / Normal mode	20
Working instructions	20
– Working with the lawn trimmer	20
Maintenance and care	21
– Maintenance	21
– Replacing the thread spool roll	21
– Sharpening or replacing the thread knife	21
– Cleaning	21
Transport	21
Storage	22
Possible faults	22
Technical data	23
Disposal	23
Guarantee	23

Extent of delivery

After unpacking, check the contents of the box

▶ That it is complete
▶ Check for possible transport damage

Report any damage or missing items to your dealer or the manufacturer immediately. Complaints made at a later date will not be acknowledged.

• 1 Lawn trimmer - upper part
• 1 Lawn trimmer - lower part
• 1 Protective hood
- 1 Front handle
- 1 Screw bag
• 1 Operating manual
• 1 Assembly and operating instruction sheet
• 1 Warranty declaration

The following parts are not included in the scope of delivery. These accessories are available from your dealer or manufacturer:

• Charging unit ALG 40-1800 (Order-no. 365500)
• Battery AP 40-2000 (Order-no. 365501) and / or
• Battery AP 40-4000 (Order-no. 365503)

Operating times

Please consider the individual country specifications.

Information on how to avoid noise:

Some noise exposure from this machine is unavoidable. Schedule noisy work to times during which it is allowed. Respect all rest times and restrict the work duration to the minimum. You as the operator and bystanders should wear a suited hearing protection.

EC Declaration of Conformity

No. (S-No.): 18721

according to EC directive 2006/42/EC

We, ATIKA GmbH

Josef-Drexler-Str. 8, 89331 Burgau - Germany

herewith declare under our sole responsibility that the product

Rasentrimmer (Lawn trimmer) GTC 40-305

Serial number: 000001 - 020000

is conform with the above mentioned EC directives as well as with the provisions of the guidelines below:

2014/30/EU, 2011/65/EU, 2000/14/EC + 2005/88/EC

Conformity assessment procedure:

2000/14/EC - Appendix V + 2005/88/EC.

Measured sound power level L_WA 93.2 dB (A).

Guaranteed sound power level L_WA 96 dB (A).

Following harmonized standards have been applied:

EN 60335-1:2012+A11:2014, EN 50636-2-91:2014,

EN 55014-1:2006+A1:2009+A2:2011,

EN 55014-2:1997+A1:2001+A2:2008

Duly authorised person for the compilation of technical documents:

ATIKA GmbH – Technical department –

Josef-Drexler-Str. 8, 89331 Burgau – Germany

i.A. f A

Burgau, 04.07.2018

i.A. G. Koppenstein

Engineering design management

Symbols original instructions

	Threatened hazard or hazardous situation. Not observing this instruction can lead to injuries or cause damage to property.
	Important information on proper handling. Not observing this instruction can lead to faults.
	User information. This information helps you to use all the functions optimally.
	Assembly, operation and servicing. Explanation of what exactly needs to be done.
	Please refer to the attached assembly and operating instruction sheet for references to figure numbers in the text.

Symbols on the machine

Memorise the meaning to be able to operate the device more safely and to protect yourself and other from possible injuries.

① Refer to the respective "Operating instructions" for the meaning of the "Symbols" of the batteries and the charger.

	Warning!
	Carefully read the operator's manual before handling the machine. Observe instructions and safety rules when operating.
	Danger - objects may be thrown out at high speed when motor is running.Keep people, pets and domestic animals out of the danger area.
	Pull out the battery⇒ before starting any work (cleaning, maintenance, repair, etc.) on the device.⇒ when interrupting work, during transport and storage.
	Wear eye and ear protection.
	Wear protective gloves.
	Wear safety shoes.
	Do not expose to rain. Protect against humidity.
	Do not use metallic cutting tools.
	Direction of rotation and max. speed of thread spool 9000 rpm
	Keep children, bystanders and animals at a distance from your working area. Safety distance at least 15 m.
		Danger by after-running tool!
	Device in normal modeDevice in economy mode
	This product complies with European regulations specifically applicable to it.
	Electrical devices do not go into the domestic rubbish. Give devices, accessories and packaging to an ecofriendly recycling.According to the European Directive 2012/19/EC on electrical and electronic scrap, electrical devices that are no longer serviceable must be separately collected and brought to a facility for an environmentally compatible recycling.

Proper use

• This lawn trimmer is designed for cutting grass and similar soft vegetation and for trimming lawn edges in private and hobby garden areas which are not accessible with a lawnmower.
• The device is not allowed to be used in public gardens, parks, sports centres or at roadsides as well as in agriculture and forestry.
• This lawn trimmer is not allowed to be used for cutting or chopping:

— hedges, shrubs and bushes,
- flowers,
– in terms of composting.

Otherwise, there is a risk of injury.

• Equipment that is not used in public areas, parks, sports facilities as well as in agriculture and forestry is regarded as lawn trimmer for private home gardens and hobby gardens.
• The intended usage also includes compliance with the assembly, operating, servicing and repair conditions prescribed by the manufacturer and following the safety instructions included in the instructions.
• The relevant accident prevention regulations for the operation as well as the other generally acknowledged occupational medicine and safety rules must be complied with.
• Any other use is deemed not to be use as prescribed. The manufacturer is not liable for any type of damage resulting from this: the user bears the sole risk.
• Unauthorised modifications at the lawn trimmer will exempt the manufacturer from any liability for damages of any kind arising from this.
• Only persons who are familiar with the device and informed about possible risks are allowed to prepare, operate and service this device. Repair work may only be carried out by us or a customer service agent authorised by us.
• The machine may not be used in a potentially explosive environment or be exposed to rain.

Residual risks

Even if used properly, residual risks can exist even if the relevant safety regulations are complied with due to the design determined by the intended purpose.

Residual risks can be minimised if the "Safety information" and the "Intended usage" as well as the whole of the operating instructions are observed.

Observing these instructions and taking proper care will reduce the risk of personal injury or damage to the equipment.

- Warning! This device generates an electromagnetic field during operation. Such a field may affect active or passive medical implants under certain circumstances. To reduce the risk of serious injuries we recommend persons who carry medical implants to consult their doctor and the manufacturer of the medical implant before operating this device.

• Health impairment resulting from exposure to hand arm vibration if the machine is used too long or is not properly guided and maintained.
• Risk of injuries of fingers and hands by contact with the rotating cutting tool.
• Risk of injury at feet by contact with the cutting tool at a no-covered area.
• Risk of injury from stones and earth flung away.
• Impairment of hearing when working on the machine for longer periods of time without ear protection.
• Eye injury when failing to wear safety goggles or visor.
• Electric shock.
• Touching live parts of opened electrical components.
• Fire danger

In addition, in spite of all the precautionary measures taken, non-obvious residual risks can still exist

Vibrations (hand arm vibrations)

Vibration a_h = 3.5 m/s^2

Measuring uncertainty K = 1.5 m/s^2

The indicated vibration emission level has been measured according to a standardised test method and can be used to compare power tools.

It can also be used for an initial estimate of the vibration exposure.

Warning:

The actual vibration emission level during the use of the machine may differ from that indicated in the operating instructions or indicated by the manufacturer. This may be caused by the following factors to be minded before and during the use:

– Proper use of the machine.
– Correct cutting or machining of material.
– Proper condition of the machine for use.
– Use of the correct and sharp cutting tool.
- Handles and optional anti-vibration handles properly mounted on the machine body.

When you feel uncomfortable or notice discoloration of skin on your hands during the use of the machine, stop working immediately. Observe sufficient break times to rest. Failure to have sufficient break times may result in a hand-arm vibration syndrome.

The extent of exposure depending on the type of work or machine use should be estimated and appropriate breaks taken. In this way, the extent of exposure can be considerably reduced over the entire work time. Minimise the risk caused by vibrations. Maintain this machine according to the instructions in the manual.

Avoid the use of this machine at temperatures under 10^ C.

Create a work schedule in order to minimise vibration exposure.

Safety instructions

Observe the following advice in order to protect yourself and other persons against possible injuries.

Before starting this device, read and keep to the following advice. Also observe the preventive regulations of your professional association and the safety provisions applicable in the respective country, in order to protect yourself and others from possible injury.

National regulations can restrict the use of this machine.

i

Pass the safety instructions on to all persons who work with the machine.

i

Keep the instructions in a safe place for future use.

• Familiarise yourself with the unit, the adjustment elements and the proper use of the unit before using it by referring to the original operating instructions.
• Do not use the machine for unsuitable purposes (see "Normal intended use").
• Be attentive. Be careful what you do. Behave sensibly when working. Do not use the device when you are tired or under the influence of drugs, alcohol or medicaments. One moment of carelessness when using the device can result in serious injuries.
• The operator is responsible for accidents or risks which occur to other persons or their properties.

Personal protective equipment

• Always wear suitable work clothing when operating the machine:
• do not wear loose-fitting clothes or jewellery; they can catch in moving parts
• no loose clothing or such with hanging bands or drawstrings
• wear a hair-net if your hair is long
• eye- and ear protection
  – protective jacket with striking colour
  – cut-proof trousers and gloves
• Anti-slipping cut-proof boots (safety shoes) with steel-toes
• First-aid material
  – Mobile telephone if required

Safety instructions —before working

Carry out the following checks before the initiation and regularly during the working process. Observe the relevant sections in the operating instruction manual:

• Is the device assembled completely and properly?
  • Is the device in good and safe condition?
  Never use the device with a damaged cover or protective device or without a cover or protective device.

• Are the handles clean and dry?

• Check the machine for loose fasteners and damaged parts such as cracks in the tool.

• Before starting your work make sure that:
• no other persons, children or animals stay within the working area,
• you can always step back without any barriers,
• your standing area is free from foreign objects, brushwood and branches,
• you always have a secure standing position.

- Is the workplace free of risks to stumble? Keep your workplace in an orderly condition! Untidiness can result in accidents. Risk of stumbling.

- Before trimming, remove all foreign objects (e.g. stones, branches, wires, etc.). While working watch out for further foreign objects.

• Take into consideration environmental influences:

- Do not work under inadequate lighting conditions (e.g. during fog or dusk) but only in daylight or good artificial lighting. Otherwise, you will no longer be able to see details within the falling area – risk of accident!

- Do not work in bad weather conditions (e.g. rain, risk of lightning, snow flurry)

- Do not use the device near inflammable liquids or gases - Risk of fire.

Safety instructions - operation

• Never work with only one hand. Hold the device always firmly with both hands.
• Never work
  – with stretched arms
  — on hardly accessible places
• above shoulder height
  standing on a ladder, a staging or a tree.
  • Always work on non-skid and flat ground.
• Avoid abnormal posture. Provide a safe standing position and keep at any time the balance.
• When working on slopes always make sure to have a safe standing position.
• Only move the machine at walking speed, never run with it.
• Change your working posture from time to time.
• To have a break stop the machine and place it so that nobody is at risk. Secure the device against unauthorized access.

Safety instruction – while working

• Never work alone. Keep acoustic and visual contact to other persons at all times to allow immediate first aid in emergency cases.
• Wear eye protection and solid shoes the whole time you are using the machine.
• Immediately stop the engine at imminent danger or in emergency cases
• Never leave the device running unattended.
• Immediately stop working when you feel unwell (e.g. headache, dizziness, nausea, etc.). Otherwise there is an increased risk of accidents.
• Make sure that the cutting tool is free before starting the engine.

GB

• Risk of injury! Before starting the engine, make sure that your hands and feet are kept at a safe distance to the cutting tool.
• Risk of injury! The cutting tool may after-run. Do not try to slow it down by hand.
• Start cutting only when the cutting tool has reached the full rotational speed.
• Do not overload the machine! You work better and safer in the given performance range.
• Take breaks when working so that the motor/battery can cool down.
• Take breaks when working so that the motor/battery can cool down.
• Do not place a hot machine in dry grass or onto inflammable objects.
• Never bring the cutting tool in contact with rigid objects (stones, trunks).

General safety instructions

- Stop the machine and remove the battery when:

• the cutting tool comes in contact with stones, nails or other foreign objects, to check the device for damages
• carrying out repair works
• maintenance and cleaning
  – removing malfunctions and blockages
  – check if the unit starts to vibrate excessively
• transport and storage

• replacing the cutting tool
  – Leaving the machine (also during temporary interruption)

• Do not touch dangerous moving parts before the battery has been pulled out of the device and such moving parts have come to a standstill.

• Maintain the machine carefully:

- Follow the maintenance instructions and the instructions for tool exchange.

- Keep the handholds dry and free from resin, oil and grease.

• Always keep the machine including tool in a good condition.
- Make sure to check the machine before any use and after dropping or other impacts to ensure that it is in a proper condition.
- Check the machine for possible damage:

- Before further use of the machine the safety devices must be checked carefully for their proper and intended function. Only operate the device with complete and correctly attached safety equipment and do not alter anything on the device that could impair its safety. Only operate the machine with complete and correctly attached safety equipment and do not alter anything on the machine that could impair the safety.

• Check whether the movable parts function perfectly and do not stick or whether the parts are damaged. All parts must be correctly installed and fulfil all conditions to ensure perfect operation.
• Damaged guards and parts must be properly repaired or exchanged by a recognized, specialist workshop; insofar as nothing else is stated in the instructions for use.

• Damaged or illegible security labels have to be replaced.

• Do not allow any tool key to be plugged in! Before switching on, check always that all tools are removed.

• Store unused equipment in a dry, locked place out of the reach of children.
• Note that a failure to maintain the unit properly, any use of non-conform spare parts or a removal / modification of safety devices can result in damages to the machine and to serious injuries of the person who works with it.

Do not carry out repair operations on the machine other than those described in section "Maintenance and care" but contact the manufacturer or authorized customer service centre.
⚠️ Use only original spare parts and accessories. Accidents can arise for the user through the use of other spare parts. The manufacturer is not liable for any damage or injury resulting from such action.

Refer to the respective "Operating instructions" for notes on the "Safety" of the battery and the charger.

Behaviour in an emergency situation

• Initiate all required first aid measures suited for the injury and seek qualified medical advice as quickly as possible.
• Protect the injured person against further injuries and immobilise the injured person.

3

Description of device / Spare parts

Please refer to the attached assembly and operating instruction sheet.

Pos.	Denomination	Order-No.
1	Cutting head	✕
2	Protective hood	380707
3	Protection bow	380708
4	Adjusting knob (Angle adjustment)	✕
5	Lawn trimmer – lower part	✕
6	Front handle	✕
7	Locking nut	✕
8	Lawn trimmer – upper part	✕
9	ECO button	✕
10	Charging unit 1.8 A (ALG 40-1800)	365500
11	Battery 2.0 Ah (AP 40-2000)	365501
12	Battery 4.0 Ah (AP 40-4000)	365503
13	Locking knob	✕
14	ON-OFF switch	✕
15	Cutting thread	✕
16	Thread knife	✕
17	Spool cover	380706
18	Thread spool roll	✕
19	Spool lower part	✕
20	Safety label 1	380704
21	Safety label 2	380703
22	Operating handle	✕
23	Replacement spool	380705

Assembling

Always start the machine when it is completely assembled.

Attaching the protective hood

→ 4 Side the protective hood (2) over the cutting head (1).
→ 4 Fasten the protective hood (2) on the cutting head (1) using the screws (M4x15).

Attaching the handle

→ 5 Slide the rubber holder on the lawn trimmer upper part (8) to the desired position where the handle (6) shall be fastened.
→ 5 Slide the handle (6) over the rubber holder and fasten it with the screws provided (M5x35).

Connecting upper- and lower part

6 Plug the lawn trimmer lower part (5) and upper part (8) together.
i Note the marks (▶◀).
6 Screw the lawn trimmer lower (5) and upper part (8) together with the locking nut (7).

Choosing cutting diameter

Danger of Cutting!

Wear protective gloves in order to avoid injury to the hands.

Select position "A" for the thread blade (16) to set a cutting diameter of ∅ 254 mm.
7 Select position "B" for the thread blade (16) to set a cutting diameter of ∅ 305 mm.

Before the first start-up

You only need to charge the battery before starting the device and insert it into the device.

8 Charging the battery:

See operating instructions for the battery and/or the charger.

→ Inserting the battery:

Slide the battery into the guide of the battery holder until the contacts of the battery are firmly seated on the contact plugs of the device (audible click).

2

The lithium ion batteries AP 40-2000 (Article No. 365501) or AP 40-4000 (Article No. 365503) as well as the charger ALG 40-1800 (Article No. 365500) are not included in the scope of delivery and must be purchased separately.

only an original battery.

not use any other charger to charge the batteries. The charger is optimally matched to the batteries. Using an unsuitable charger may present a risk of shock, overheating or escape of caustic battery fluid.

Refer to the respective "Operating instructions" for further information on the batteries and the charger.

Start-up

Caution! Prior to starting the machine learn how to put it out of action in emergency cases.
You may not start to operate the machine until you have read these operating instructions, observed all the instructions given and installed the machine as described!

Check the device before each use for

• possible damages,
  – loose fastening elements,
• correctly assembled and intact covers and protective devices.

⚠ Make sure before each startup that the switch lock and the ON / OFF switch on the operating handle work properly.

Do not use the device if it can be switched on only with the ON / OFF switch. The unit must be checked and repaired immediately by the customer service.

Switching On / Off

⚠️ Firmly hold the machine and make sure that neither the cutting tool comes into contact with fixed objects.
Always keep your hands and feet at a safe distance to the cutting tool.
⚠️ Make sure that the cutting tool has no contact with the ground.

Switch on

The lawn trimmer has a protective shut-down which prevents an unintended switching on.

→ 10 Hold the device firmly with both hands; the left hand always encloses the front handle (6) and the right hand always encloses the operating handle (22). This applies also to left-handed persons!
→ 11 Press the locking knob (13) and then the ON/OFF switch (14). While working, you can release the locking knob (13).
To protect the battery the machine automatically switches off at a low battery.

Never continue operating the ON / OFF switch; this may damage the battery.

Charge the lithium ion battery (→ "Battery" operating instructions).

Switching off

→ 11 Release the ON/OFF switch button (14).

The cutting thread is after-running once the lawn trimmer has been powered off. Therefore wait until the thread is stationary before you restart the product.

Speed control of the cutting tool

The speed of the cutting tool can be adjusted infinitely variable with the ON / OFF switch (H).

11 When pressing the ON / OFF switch only slightly, the cutting tool turns at low speed. The further the ON / OFF switch is pressed, the faster the cutting tool will turn.

Energy-saving mode / Normal mode

The device may be operated in economy mode or in normal mode.

The device always starts in normal mode.

You can only change the mode when the device is switched on.

Changing the mode

Press the green button:

The device runs in economy mode.

→ The battery charge will last longer.

The middle indicator lights up green when the device is operated in economy mode.

Press the yellow button:

The device runs in normal mode.

→ The battery life becomes shorter.

Working instructions

⚠️ You may not start to operate the machine until you have read these original instructions, observed all the instructions given and completely and properly assembled the machine!

⚠️ Always keep your hands and feet at a safe distance to the cutting tool.

Working with the lawn trimmer

Correct working position

10

Assume a secure stand, hold the device firmly with both hands; the left hand always encloses the guide handle and the right hand the operating handle. This applies also to left-handed persons!

Position the front handle (6) to allow you guiding the device securely and conveniently.
Hold the device during cutting so that - it is at an adequate distance from the body. - the guide tool is always guided below the waist.
→ Make sure the cutting tool does not lie on the ground when switching the device on.

Adjusting the cutting head angle

→ 12 The angle of the cutting head (1) can be adjusted to 3 different positions. For this, press the adjusting knob (4) and turn the cutting head (1) to your desired position.

Trimming

Switch on the lawn trimmer on a level, already mowed area.
While trimming keep the lawn trimmer away from your body at a sufficient distance. Tilt the machine slightly forward and move it smoothly and evenly from left to right.
- You will get the best trimming results when you cut dry grass.

① Wet grass is harder to cut and causes blockages more quickly.

14 Cut higher grass and denser growth above 15 cm in several passes to avoid blockages.
→ Guide the product around trees and shrubs so that the plants are not damaged. Use the protective bow (3) for better control.

i Damaged plants may die off.

Start along walls, trees, fences, lawn edges or other obstacles at a certain distance from the obstacle and work forward step by step. Do not guide the cutting thread (15) directly at walls and paving stones. Otherwise it will prematurely wear off.

① Adjust the engine speed and cutting height to the prevailing conditions. If the engine speed is too low, scrub can entangle in the cutting tool or get stuck.

⚠️ If grass, scrub or other objects entangle in the cutting tool or if the device vibrates abnormally, immediately stop the engine and check the machine.

The cutting thread is after-running once the lawn trimmer has been cut off. Therefore wait until the thread is stationary before you restart the product.

When the thread spool is empty replace it by a genuine thread spool.

Thread follow-up

During trimming, the cutting thread (15) wears (becomes shorter) or it may tear off so that it can no longer cut grass.

11 Switch off the device, release the ON/OFF switch button (14).

The cutting thread is after-running once the lawn trimmer has been powered off, before you press the thread follow-up.

Danger of Cutting!

Wear protective gloves in order to avoid injury to the hands.

→ 16 Remove the battery (11/12).

→ 17 Press the red button on the lower part of the spool (19) several times. This turns the thread spool roll further by a few notches. The cutting thread unwinds automatically when switching on the device. If the cutting thread (15) exceeds the maximum cutting diameter it will be shortened by the integrated knife (16) within the protective hood (2).

Maintenance and care

Before each maintenance and cleaning work

• switch off device
• wait until the cutting device does not longer move
• remove the battery.

Wear protective gloves during maintenance and cleaning work in the area of the cutting tool to avoid possible injuries.

Maintenance and repair work other than those described in this chapter is only allowed to be carried out by service staff.

For maintaining and cleaning, removed security devices must unconditionally be mounted properly and proved again.

Use only original parts. Other parts can result in unexpected damages and injuries.

Maintenance

The cutting tool will not come to a standstill immediately after cut-off. Before starting any service work wait until all parts are stationary.

To guarantee a long and reliable usage of the device carry out the following maintenance works regularly.

Check the machine for obvious defects such as

– loose fastening elements
- worn or damaged components
– damaged cutting tool

Necessary repair works or maintenance works have to be carried out before the usage of the machine.

Replacing the thread spool roll

→ 16 Remove the battery (11/12).
→ 20 Remove dirt and grass residues.
→ 18 Press together both locking devices (>>> ) on the spool cover (17) and pull it off.

→ 18 Remove the thread spool roll (18).
19 Thread the end of the cutting thread "C" of the new thread spool roll (18) in the opening "D" in the spool lower part (19) provided for this.
→ 19 Firmly place the thread spool roll (18) in the spool lower part (19). Make sure that the cutting thread is not caught and pull it approx. 12 cm out of the spool opening „D“.
19 Press the spool cover (17) on the spool lower part (19) until it engages with a click.

Sharpening or replacing the thread knife

→ 7 Unscrew the thread knife (16).

Clamp the thread knife into a vice and sharpen it with a flat file.

Make sure not to change the angle of the knife and file only in one direction.

File carefully.

7 Screw down the thread knife again as shown.

Do not overtighten the screws.

Do not use unsharpened or damaged thread knives. A damaged thread knife must be replaced by a new one.

Cleaning

20

i Clean the device thoroughly after each application so that the faultless function is kept.

• After work, remove grass, dirt, plant residues and moisture (plant sap) with a brush or a damp cloth from the area of the cutting tool and the guard.
• Clean the case with a soft brush or a dry cloth.
• Clean the contact plug in the battery well with a soft brush.
• Do not clean the machine under running water or using a high-pressure cleaner.
• Do not use solvents (gasoline, alcohol, etc.) for plastic parts, otherwise such parts may be damaged.
• Keep handles dry and free of oil and grease.

Water, solvents and polishing agents shall not be applied.

- Make sure the ventilation slots are free from foreign objects (risk of overheating).

For information on "Maintenance and cleaning" of the battery and the charger, please refer to the respective "Operating Instructions".

Transport

Before each transport:

• switch off device
• wait until the cutting device does not longer move
• remove battery

- Carry the device balanced on the shaft. Hold the cutting tool toward the back at this.

GB

■ When transporting the product in a car put it only in the boot or on a separate loading area.
■ You may pull the device apart to save space.
■ Do not throw the device when loading it. Secure the device against tipping over and damages.
Check the device for damages if it was subjected to hard jolts during transport.

For information on “Transport” of the battery and the charger, please refer to the respective “Operating Instructions”.

Storage

Before each storage:

• switch off device
• wait until the cutting device does not longer move

• remove battery

• Store machines that are not in use in a dry locked place protected against frost and outside the reach of children and unauthorized persons.

• Do not rest the device on the guard when storing it to avoid deformation of the guard.

• Best store the device suspended. An opening for hanging it up is provided in the housing.

• You can also store the device in a space-saving manner by loosening the locking nut (7) and pulling the upper and lower part apart.

Before storage, please observe the following to increase the service life of the device and to ensure smooth operation: - Carry out a thorough cleaning and maintenance.

i Remove the thread spool to make cleaning it and the guard easier.
→ Check the protective hood for damages during cleaning.
⇒ To keep the cutting thread flexible, it should absorb moisture before use.
Put cutting threads that were stored for a longer period or purchased new in water for 1 - 2 days before use so that they can absorb moisture.

- Check the device for perfect condition to ensure reliable use.

For information on "Storage" of the battery and the charger, please refer to the respective "Operating Instructions".

Possible faults

Before each fault elimination:

• switch off device
• wait until the cutting thread is stationary
• wear gloves
• remove the battery

After each fault clearance, put into operation and recheck all security installations.

Fault code	Possible Cause	Removal
Machine does not start after switching on	Battery run down	Charge the battery
	Battery not correct inserted	Insert the lithium-ion battery correctly
	Battery, motor or ON/OFF-switch defective	Have the battery, motor or switch checked / repaired by a licensed electrician or customer service or replaced by original spare parts.
Machine does not work with full performance	Battery run down	Charge the battery
	Battery defective	Contact the customer service
Machine cuts with interruptions	ON/OFF switch defective	Contact the customer service
	Internal fault	Contact the customer service
Device does not cut. (Poor cutting results)	Cutting thread to short/broken.	Follow up the cutting thread.
	Device overloaded as grass too high.	Trim the grass in several passes.
Cutting thread is not followed up.	No more thread on the spool.	Replace the thread spool.
	Cutting thread entangled.	Recoil the cutting thread.
Cutting time with fully charged battery too short	Rechargeable battery is low	Charging the battery
	Battery service life exhausted	Replace the battery
Device shuts off on its own	Lithium ion batteries too hot (45 °C)	Allow lithium-ion battery to cool down
	Battery charge too low	Charge the lithium ion battery
Unusual vibrations	Grass debris between thread spool and protective hood	Remove grass debris
Operating mode cannot be selected	Economy / normal mode toggle buttons defective	Contact the customer service

① In case of further faults or inquiries please contact your local dealer.

Technical data

Type	GTC 40-305
Year of construction	see last page
compatible battery voltage	36 V max. 40 V)
No-load speed no	9000 min ^-1
Cutting diameter	∅ 254 mm / ∅ 305 mm
Cutting thread diameter	∅ 1.65 mm
Thread total length	4.5 m
Sound power level Lwa (according to regulation 2000/14/EG)	measured sound power level 93.2 dB (A)guaranteed sound power level 96 dB (A)
Measuring uncertainty K	2.5 dB (A)
Sound pressure level LPA (according to regulation 2000/14/EG)	82 dB (A)
Measuring uncertainty K	2.5 dB (A)
Hand-arm vibration	ah = 3.5 m/s ^2
Measuring uncertainty K	1.5 m/s ^2
Weight (without rechargeable battery)	approx. 2.8 kg

Refer to the respective "Operating instructions" for "Technical specifications" of the batteries and the charger.

Disposal

Dispose of lawn trimmer, battery, charger, accessories and packaging in an environmentally friendly manner according to regulations.

For EU countries only.

Electrical devices do not go into the domestic rubbish.

According to the European Directive 2012/19/EC on electrical and electronic scrap, electrical devices that are no longer serviceable must be separately collected and brought to a facility for an environmentally compatible recycling.

For information on "Disposal" of the battery and charger, please refer to the respective "Operating Instructions".

Guarantee

Please observe the enclosed terms of guarantee.

Technical modifications reserved!

Inden hver transport

89331 Burgau –Germany

i.A. f i.A. G. Koppenstein.

Burgau, 04.07.2018

89331 Burgau – Germany

Burgau, 04.07.2018

i.A.. G. Koppenstein

Modul economic / normal

Vibrationer (Hand-arm-vibration)

Hand-arm-vibration a_h = 3.5 m/s^2

Osäkerhet K_hd = 1,5 m/s^2