SS501AC - Saw Vonroc - Free user manual and instructions

USER MANUAL SS501AC Vonroc

1. SAFETY INSTRUCTIONS

Read the enclosed safety warnings, the additional safety warnings and the instructions. Failure to follow the safety warnings and the instructions may result in electric shock, fire and/or serious injury. Save the safety warnings and the instructions for future reference.

The following symbols are used in the user manual or on the product:

Read the enclosed safety warnings, the additional safety warnings and the instructions. Failure to follow the safety warnings and the instructions may result in electric shock, fire and/or serious injury. Save the safety warnings and the instructions for future reference.

Denotes risk of personal injury, loss of life or damage to the tool in case of non-observation of the instructions in this manual.

Denotes risk of electric shock.

Wear ear and eye protection.

Earthing symbol. This appliance is classified as protection class I and must be connected to an earthed mains socket.

The product is in accordance with the applicable safety standards in the European directives.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1) Work area safety

a) Keep the work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your

finger on the switch or energising power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust related hazards.
h) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

5)Service

a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

SPECIFIC SAFETY INSTRUCTIONS

• Wear safety goggles and a dust mask.
  This scroll saw machine is for indoor use only.
• Ensure that the teeth of the saw point downwards prior to using the machine.
• If teeth of the saw blade are missing or are damaged, then the saw blade must be replaced immediately.
• Use the scroll saw machine on a stable and flat surface.
• Never exert pressure on the sides of the saw blade because it may break.
• Check wooden work pieces for possible protruding nails etc. and remove these.
• Do not touch the sawing surface with your hands.
• Never leave the sawing machine unattended while it is running.
• Do not remove any wood debris etc, in the vicinity of the saw with your hands while it is running. Turn the machine off before removing the wood debris.

Immediately switch off the machine when

• Interruption in the mains plug, mains lead or mains lead damage.
  Defect switch.
  Smoke or stench of scorched isolation.

Electrical safety

Always check that the voltage of the power supply corresponds to the voltage on the rating plate.

• Do not use the machine if the mains cable or the mains plug is damaged.
• Only use extension cables that are suitable for the power rating of the machine with a minimum thickness of 1.5mm^2 . If you use an extension cable reel, always fully unroll the cable.

2. MACHINE INFORMATION

Intended use

This scroll saw is great for making toys, puzzles, games, fretwork and jewelry. Because of its cutting capacity it is a handy do-it-yourself tool. It cuts wood up to 50 mm thick as well as plastics and non-ferrous metals.

Model No. SS501AC
Voltage 230 V ~
Frequency 50 Hz
Power input 120 W (S6 30%)
No-load speed 400 - 1600 min	-1
Blade length 125mm
Max. Cutting depth at 90° 50mm
Max. Cutting depth at 45° 23mm
Max. Cutting length/working depth	406mm
Weight 11kg
Sound pressure (LPA) 71 dB(A)	K=3dB
Acoustic power (LWA) 84 dB(A)	K=3dB
Protection type Class I

DESCRIPTION

The numbers in the following text refer to the pictures on page 2 - 4.

1. On/off switch
2. Angle adjustment knob
3. Speed adjustment knob
4. Saw blade holder
5. Protective cover
6. Spanner
7. Dust blow pipe
8. Workpiece holder

9. Table inlay
   10.Foot pedal switch
   11.Connection vacuum cleaner

10. Locking knob

11. Operation switch
12. LED Work light

3. ASSEMBLY

Before assembly, always switch off the machine and remove the mains plug from the mains.

Install of a stationary machine (Fig. B)

This machine is a stationary machine and for safety reasons we recommend the machine to be firmly installed and not used for mobile applications.

The machine can be mounted to a workbench as shown on Fig. B. The machine must be mounted on the same 4 points that the rubber feet are assembled. Each of the 4 points must be secured with a bolt, washer and nut. The necessary tools and small parts for assembling the saw on a workbench are not supplied with the saw.

Installing the protective cover (Fig. C)

Before commissioning the machine, the protective cover (5) must be installed.

• Mount the protective cover on the metal part as shown on Fig. C
• Insert the screw as shown on Fig. C.
• Screw the nut tightly.

4. OPERATION

Always observe the safety instructions and obey the relevant regulations.

Switching on/off (Fig. A)

Place the machine onto a flat and solid surface. Place the Foot pedal switch (10) on the ground. The machine can be switched on/off when the pedal is actuated. A foot pedal switch for switching on/off is practical, especially for internal cuttings, since your hands are kept free and you can fully concentrate on the work piece under the scroll saw. The foot pedal switch cannot influence the speed (see below Speed Adjustment).

Beware of unintentional actuation of the foot pedal switch.

Caution! Always choose the preferred operation mode with the Operation switch (13) before using the machine. The machine will not start in '0' mode.

Continuous operating mode

• Use the Operation switch (13) to choose for 'I' continuous operation.
• Connect the scroll saw to the mains.
• Start the machine by pushing the green ON-switch (1).

Push the red OFF-switch (1) to turn the machine off.

Foot pedal operating mode

• Use the Operation switch (13) to choose for 'll' foot pedal operation.
• Connect the scroll saw to the mains.
• Push the green ON-switch (1).
• Start the machine by pushing the Foot pedal switch (10) with your foot.

To stop the machine, release the Foot pedal switch (10). Push the red OFF-switch (1) to turn the machine off.

Tilting the table (Fig. A, D)

The scroll saw table can be tilted from 0 to 45^ . To do so:

• Untighten the Angle adjustment knob (2) by turning it anti-clockwise.
• Manually tilt the table until the desired angle has been reached (see the graduated scale on the machine).
• Retighten the Angle adjustment knob (2) by turning it clockwise.

Removing the saw blade (Fig. E)

Always disconnect the machine from the main power supply before carrying out any maintenance work.

• Untighten the Spanner (6) by turning it clockwise until the spring is slack.
  Pull the Table inlay (9) upwards out of the saw table to achieve a clear view of the blade, as shown on fig. E1.

• Carefully push down the upper saw-blade holder and slightly lift the blade in order to facilitate its removal, as shown on fig. E2.

• Allow the blade to drop down slightly and push it forward, in order to loosen it from the lower holder.

Installing the saw blade (Fig. E)

Always disconnect the machine from the main power supply before carrying out any maintenance work.

• Select the correct blade for the kind of wood to be cut.
• Untighten the Spanner (6) by turning it clockwise until the spring is slack.
  Pull the Table inlay (9) upwards out of the saw table to achieve a clear view of the blade, as shown on fig. E1.
• Push the saw blade through the slot, with the teeth pointing downwards. Make sure that the bolt of the saw blade (or saw-blade adapter) slides into the lower saw blade holder.
  Pull the saw blade up, so that the upper bolt (or saw-blade adapter) slides into the upper holder.
• Push the Table inlay (9) downwards into the saw table.
• Retighten the Spanner (6) by turning it anticlockwise until the saw blade has the required tension.
• Remove all tools and other objects from the saw table. Activate the current and allow the saw blade to run before starting to saw. The saw blade should run quietly.

Adjusting the saw blade position (Fig. F)

The saw blade can be mounted in two different positions: regular frontal position as shown on Fig. F1 and in sideways position as shown on Fig. F2. When using the sideways position, even longer workpieces can be sawed with ease.

Adapters for universal saw blades (Fig. G)

The enclosed adapters should only be used with universal (= without pins on the end) saw blades.

• Unscrew the Allen screws on the adapter anticlockwise as shown on fig. G1.
• Slide the universal saw into the gap between her Allen screws.
• Tighten the Allen screws clockwise so the saw is clamped.
• Install the saw blade (see INSTALLING THE SAW BLADE) on the saw blade holders as shown on fig. G2.

Workpiece holder (Fig. A, H)

The workpiece holder (8) is used to hold the workpiece to the saw table, preventing the workpiece from moving up and down due to the movement of the blade. The workpiece holder must be adjusted in height depending on the thickness of the workpiece.

• Untighten the Locking knob (12) by turning it anti-clockwise.
• Adjust the height of the Workpiece holder (8) to the desired height.
• Retighten the Locking knob (12) by turning it clockwise.

Speed Adjustment (Fig. A)

The required speed can be adjusted by using the Speed adjustment knob (3). Also during running the rotational speed can be adjusted.

To increase the speed, turn the Speed adjustment knob (3) clockwise.
- To decrease the speed, turn the Speed adjustment knob (3) anti-clockwise.

The required speeds depend on the material and can be determined by practical testing.

Sawdust blower (Fig. A)

The sawdust blower keeps the workpiece clean for more accurate scroll cuts. For best results, always direct air flow from the dust blow pipe at the blade and workpiece. To adjust, simply bend to desired position.

5. MAINTENANCE

Always disconnect the machine from the main power supply before carrying out any maintenance work.

The machine is designed to function faultlessly for a long period and with a minimum of maintenance.

Extend its lifespan by regularly cleaning the machine and treating it correctly.

Cleaning

Regularly clean the machine with a soft cloth, preferably after each use. Keep the ventilator slot free of dust and other deposits. Remove any tenacious deposits with a soft cloth moistened with soap. Do not use solvents (petrol, alcohol, ammonia, etc.) as they will damage the plastic parts.

Replacing the supply cord

If the replacement of the supply cord is necessary, this has to be done by the manufacturer or his agent in order to avoid a safety hazard.

Replacing cables or plugs

Dispose of old cables or plugs immediately after replacing them. It is dangerous to connect the plug of a loose cable to a wall socket.

ENVIRONMENT

and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations.

Only for EC countries

Do not dispose of power tools into domestic waste. According to the European Guideline 2012/19/EU for Waste Electrical and Electronic Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly way.

WARRANTY

VONROC products are developed to the highest quality standards and are guaranteed free of defects in both materials and workmanship for the period lawfully stipulated starting from the date of original purchase. Should the product develop any failure during this period due to defective material and/or workmanship then contact VONROC directly.

The following circumstances are excluded from this guarantee:

• Repairs and or alterations have been made or attempted to the machine by unauthorized service centers;
  Normal wear and tear;
  The tool has been abused, misused or improperly maintained;
• Non-original spare parts have been used.

This constitutes the sole warranty made by company either expressed or implied. There are no other warranties expressed or implied which extend beyond the face thereof, herein, including the implied warranties of merchantability and fitness for a particular purpose. In no event shall VONROC be liable for any incidental or consequential damages.

The dealers remedies shall be limited to repair or replacement of nonconforming units or parts.

The product and the user manual are subject to change. Specifications can be changed without further notice.

2.INFORMATIONSRELATIVES A LA MACHINE

Introduction

CHARACTERISTIQUES DU PRODUIT

DECLARATION OF CONFORMITY SS501AC - SCROLL SAW MACHINE

(EN) We declare under our sole responsibility that this product is in conformity with directive 2011/65/EU of the European parliament and of the council of 8 June on the restriction of the use of certain hazardous substances in electrical and electronic equipment is in conformity and accordance with the following standards and regulations:
(DE) Der Hersteller erklärt eigenervertantwortlich, dass这点 Produkt der Direktive 2011/65/EU des Europäischen Parlaments und des Rats vom 8. Juni 2011 über die Einschränkung der Anwendung von bestimmten gefährlichen Stoffen in elektrischen und elektronischen Geräten entspricht. den folgenden Standards und Vorschriften entspricht:
(NL) Wij verklaren onder once volledige verantwoordelijkheid dat dit product voldoet aan de conform Richtlijn 2011/65/EU van het Europees Parlement en de Raad van 8 Juni 2011 betreffende beperking van het gebruik van bepalde gevaarlijke stoffen in elektrische en elektronische apparatus en in overeenstemming is met de volgende standaarden en reguleringen:
(FR) Nous déclarons sous notre seule responsabilité que ce produit est conforme aux standards et directives suivants: est conforme à la Directive 2011/65/EU du Parlement Européen et du Conseil du 8 juin 2011 concernant la limitation d'usage de certaines substances dangereuses dans l'équipement électrique etlectronique.
(ES) Declaramos bajo nuestra exclusiva responsabilidad que este producto cumple con las siguientes normas y estandares de configuracion: se encuentra conforme con la Directiva 2011/65/UE del Parlamento Europeo y del Consejo de 8 de junio de 2011 sobre la restricción del uso de determinadas sustancias peligrosas en los equipos electricos y electrónicos.
(IT) Dichiariamo, sotto la nostra responsabilità, che questo prodotto è conforme alle normative e ai regolamenti seguenti: è conforme alla Direttiva 2011/65/UE del Parlamento Europeo e del Consiglio dell'8 giugno 2011 sulla limitazione dell'uso di determinate sostanze pericolose nelle apparecchiature elettriche ed elettroniche.
(SV) Vi garanterar pá eget ansvar att denna produit upp fyller och följer böjlande standarder och bestämmelser: uppfyller direktiv 2011/65/EU frän Europeiska parliamentet och EG-rädet frän den 8 Juni 2011 om begränsningen av använding av farlga substanser i elektrisk och elektronisk utrustning.

(DA) Vi erklærer under eget ansvar, at dette produit er i overensstemmelse med falgende standarder og bestemmelser: er i overensstemmelse med direktiv 2011/65/EU fra Europa-Parlamentet og Rådet af 8. Juni 2011 om begrænsning af anvendelsen af visse farlige stoffer i elektrisk og elektronisk udstyr.
(PL) Deklarujemy na wlasna odpowiedzialnosc, ze ten produkt spehnia wymogi zawarte w nastepujacych normach i przyepsach: jest zgodny z Dyrektywa 2011/65/UE Parliamentu Europejskiego i Rady zdnia 8 czerwca 2011 r. w sprawie agraniczenia stosowania niedtorych niebepezecnych substantcjiw sprzecie elektrycznym i elektronicznym.
(RO) Declarãm prin aceasta cu raspunderea deplină că produsul acesta este in conformitate cu urmâtoarele standarde sau directive: este in conformitate cu Directa 2011/65/UE a Parliamentului Europeano si a Consiliului din 8 iunie 2011 cu privire la interzicerea'utilizarii anumitor substante periculoase la echipamentele electrice si electronice.
(PT) Declaramos, sob)nossa exclusiva responsabilitadede,que este produits estem conformidade com a directiva 2011/65/UE do Parliamento Europeu e com a direcva do consulho de 8 de Junho sobre a restricao dautilização de determinadas substancias perigosas em equipamento eletrico e electrónico está em conformidade e de acordo com as segunte normas e regulamentacoes:
(HU) Kizárólagos felelosségunk tudataban kijelentjuk, hogy a termek megfelel az Europai Parlamentnek és a Tanácsnak az egyes vesélyes anyagok elektromos és elektronikus berendezesekben való alkalmazásának korlátozásárol szólo 2011/65/EU irányelvenek (június 8.), valamint a következő szabványoknek és jogszabályoknek:
(CS) Prohlasujeme na svou vyhradni odpovednost, ze tento vyrobek splnju pozadavky smernice 2011/65/EU Evropske rady a parlementu ze dne 8. cervna, ktera se tyká omezeni použivani urcitych nebezpechnych latek v elektrickych a elektronickych zaizenich, a splnju take vsechny pozadavky nasledujicich norem a prdepisu:

EN ISO 12100, EN 62841-1, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3, 2006/42/EC, 2014/30/EU, 2011/65/EU, 2012/19/EU

Zwolle, 01-12-2022 H.G.FRosberg CEO

VONROC - Lingenstraat 6 - 8028 PM Zwolle - The Netherlands

VONROC

BUILD YOUR FUTURE

©2022 VONROC

WWW.VONROC.COM

2212-19