PD60LM61SP - Lawn mower Powerworks - Free user manual and instructions

USER MANUAL PD60LM61SP Powerworks

Exterior view of a power lawn mower with visible branding and wheels (no text or symbols on the device itself)

LMC406

CE

Original Instructions / Übersetzung der Originalanweisungen / Traducción de las instrucciones originales / Traduzione delle istruzioni originali / Traduction des instructions d'origine / Vertaling van de originele gebruiksaanwijzing / Alkuperäisten ohjeiden käännös / Översättning av original instruktionerna / Produsentens instruksjoner / Oversættelse af de originale vejledninger / Překlad originálního návodu / Preklad originálneho návodu / Prevod originalnih navodil / Prijevod izvornih uputa / Az eredeti utasítás fordítása / Превод на оригинаналните инструкции / Orijinal Talimatlann Tercümesi / Originaalkasutusjuhendi tõlge

English

EN

1 Description.... 4

1.1 Purpose......4
1.2 Overview.... 4

2 Safety.... 4

3 Installation...... 4

3.1 Unpack the machine......4
3.2 Unfold the lower handle....4
3.3 Install the upper handle ....4
3.4 Install the grass catcher.... 5
3.5 Install the mulch plug....5
3.6 Set the blade height.... 5
3.7 Install the battery pack.... 5
3.8 Remove the battery pack.... 5

4 Operation....5

4.1 Start the machine.... 5
4.2 Stop the machine.... 5

4.3 Automatic boost function....6
4.4 Operate the self-propel system.... 6
4.5 Empty the grass catcher....6
4.6 Operate on slopes....6
4.7 Operation tips....6

5 Maintenance......6

5.1 General maintenance....6
5.2 Lubrication....7
5.3 Replace the blade.... 7
5.4 Store the machine....7
5.5 Stand the machine on end.... 7

6 Troubleshooting......7

7 Technical data.... 8

8 Warranty....8

9 EC Declaration of conformity......8

1 DESCRIPTION

1.1 PURPOSE

This machine is used for domestic lawn mowing. The cutting blade must be approximately parallel to the ground. All four wheels must touch the ground while you mow.

1.2 OVERVIEW

Figure 1 - 12

1	Handle knob
2	Lower handle
3	Bracket
4	Upper handle
5	Bolt
6	Knob
7	Grass catcher
8	Mulch plug
9	Rear discharge door
10	Grass catcher handle
11	Hook
12	Slot
13	Mulch plug handle
14	Discharge chute
15	Height adjustment lever
16	Battery door
17	Battery compartment
18	Safety key
19	Battery release button
20	Start button
21	Handle bar
22	Bail switch
23	Self-propel lever
24	Speed control button
25	Blade
26	Wood
27	Mounting screw
28	Key cover
29	Spacer
30	Post
31	Tab
32	Storage switch

2 SAFETY

WARNING

Make sure that you do/obey all safety instructions.

Refer to Safety Manual.

3 INSTALLATION

WARNING

Do not change or make accessories that are not recommended by the manufacturer.

WARNING

Do not put in the safety key or the battery pack until you assemble all the parts.

3.1 UNPACK THE MACHINE

WARNING

Make sure that you correctly assemble the machine before use.

WARNING

• If the parts have damage, do not use the machine.
• If you do not have all the parts, do not operate the machine.

• If the parts are damaged or missing, speak to the service center.

• Open the package.

• Read the documentation in the box.
• Remove all the unassembled parts from the box.
• Remove the machine from the box.
• Discard the box and package in compliance with local regulations.

3.2 UNFOLD THE LOWER HANDLE

Figure 2.

1. Pull and turn the handle knobs 90°.
2. Unfold the lower handle.
3. Line up the handle knobs in one of the three positions on the brackets.
4. Turn the handle knobs 90° until they engage the holes in the brackets.

i NOTE

Make sure that the two handle knobs are in the same position.

WARNING

Do not make damage to the cables when you fold or unfold the handle.

3.3 INSTALL THE UPPER HANDLE

Figure 3.

1. Align the holes in the upper handle and the lower handle.
2. Put the bolts through the holes.
3. Tighten the knobs onto the bolts.
4. Do the same operation on the other side.

3.4 INSTALL THE GRASS CATCHER

Figure 4.

1. Remove the mulch plug.
2. Open the rear discharge door and hold it.
3. Hold the the grass catcher by its handle and put the hooks over the slots.
4. Close the rear discharge door.

3.5 INSTALL THE MULCH PLUG

Figure 5.

1. Remove the grass catcher.
2. Open the rear discharge door and hold it.
3. Push the latches on each side of the mulch plug handle and fit it in the discharge chute.
4. Attach the mulch plug in the discharge chute until the tabs engage the holes behind the mower deck.
5. Close the rear discharge door.

3.6 SET THE BLADE HEIGHT

The machine can be set to different blade heights.

Figure 6.

1. Pull the height adjustment lever rearward to increase the blade height.
2. Pull the height adjustment lever forward to decrease the blade height.

3.7 INSTALL THE BATTERY PACK

Figure 7.

WARNING

• If the battery pack or charger is damaged, replace the battery pack or the charger.
• Stop the machine and wait until the engine stops before you install or remove the battery pack.

• Read, know, and follow the instructions in the battery and charger manual.

• Open the battery door.

• Align the lift ribs on the battery pack with the grooves in the battery compartment.
• Push the battery pack into the battery compartment until the battery pack locks into place.
• When you hear a click, the battery pack is installed.
• Close the battery door.

NOTE

The engine starts only when you put in the safety key.

3.8 REMOVE THE BATTERY PACK

Figure 7.

1. Remove the safety key.
2. Open the battery door.
3. Push and hold the battery release button.
4. Remove the battery pack from the machine.

4 OPERATION

WARNING

Wear eye protection during operation.

4.1 START THE MACHINE

Figure 7 - 8.

1. Open the key cover.
2. Put in the safety key.
3. Push and hold the start button.
4. While you hold the start button, pull the bail switch in the direction of the handle bar.
5. Release the start button to start the machine.

Soft-Start

This Li-ion machine has a "soft-start" feature.

When you start the machine, it goes to full speed after approximately 3 seconds.

NOTE

If the machine does not start, remove the battery pack and examine the mower deck to make sure that:
- no grass catches on the blade.
• the blade can turn freely by hand.

4.2 STOP THE MACHINE

Figure 8.

1. Release the bail switch to stop the machine.

WARNING

Wait until the blades fully stop before you start the machine again. Do not quickly turn the machine off and on.

WARNING

Always remove the safety key and battery pack after you complete the work.

4.3 AUTOMATIC BOOST FUNCTION

When the machine cuts high grass the rpm is automatically increased in order to keep a good cutting and collecting results.

When the machine goes back to usual cutting conditions the rpm automatically goes back to the standard rpm to keep work time.

4.4 OPERATE THE SELF-PROPEL SYSTEM

Figure 8.

1. Start the machine.
2. While you hold the bail switch, push the self-propel lever in the direction of the handle bar.
3. Hold the bail switch and the self-propel lever at the same time with your right hand.
4. Adjust the speed control button with your left hand.
5. Push the speed control button in the direction of the Rabbit Symbol to increase the speed.

6. Pull the speed control button in the direction of the Turtle Symbol to decrease the speed.

7. Release the self-propel lever to close the self-propel system.

4.5 EMPTY THE GRASS CATCHER

Figure 9.

1. Stop the machine.
2. Remove the safety key.
3. Remove the battery pack.
4. Open the rear discharge door and hold it.
5. Hold the grass catcher by its handle and unhook it from the slots.
6. Close the rear discharge door.
7. Empty the grass catcher.

4.6 OPERATE ON SLOPES

WARNING

Do not mow on the slopes with decline more than 15^ . If you are not comfortable, do not mow on a slope.

WARNING

Please keep a low self-propelled speed when you mow on a slope.

- Do not go up and down on a slope when you mow across the face of the slope. Be careful when you change the direction on a slope.

• Monitor the holes, ruts, rocks, and other hidden objects that can cause you to fall. Remove all obstacles such as rocks and tree limbs.
• Make sure that your footing is stable. If you are out of balance, release the bail switch immediately.
• Do not mow near drop-offs, ditches, or embankments.

4.7 OPERATION TIPS

• Do not try to override the operation of the start button or bail switch.
• Do not tilt the machine when you start it.
• Do not put hands or feet near or below the turning parts.
• Keep the discharge chute clean.
• Do not cut wet grass.
• Higher blade height is necessary for new or thick grass.
• Clean the bottom of the mower deck after each use. Remove grass clippings, leaves, dirt, and other debris.

5 MAINTENANCE

WARNING

Remove the safety key and battery pack from the machine before maintenance.

WARNING

Keep the engine and battery pack free from grass, leaves or too much grease.

CAUTION

Use only approved replacement parts.

CAUTION

Do not let brake fluids, gasoline, petroleum-based materials touch the plastic parts. Chemicals can cause damage to the plastic, and make the plastic unserviceable.

CAUTION

Do not use strong solvents or detergents on the plastic housing or components.

5.1 GENERAL MAINTENANCE

• Before each use, examine the machine for damaged, missing, or loose parts such as screws, nuts, bolts and caps.
• Tighten correctly all the fasteners and caps.
• Clean the machine with a dry cloth. Do not use water.

5.2 LUBRICATION

Apply sufficient quantity of high grade lubricant to all bearings. No more bearing lubrication is necessary in usual operation conditions.

WARNING

Do not lubricate the wheel components. Lubrication can cause damage to the wheel components during operation.

5.3 REPLACE THE BLADE

Figure 10 - 11.

WARNING

Use only approved replacement blades.

WARNING

Wear heavy gloves or wind cloth around the blade when you touch the blade.

1. Stop the machine.
2. Make sure that the blades fully stop.
3. Remove the safety key and battery pack.
4. Turn the machine to its side.
5. Use a piece of wood to prevent the movement of the blade.
6. Remove the mounting screw and spacer with a wrench or socket.
7. Remove the blade.
8. Install the new blade. Make sure that the two posts engage the holes in the blade.
9. Put in the spacer and tighten the mounting screw that you removed.
10. Do the same operation on the other blade.

5.4 STORE THE MACHINE

• Clean the machine before storage.
• Make sure the engine is not hot when you store the machine.
• Make sure that the machine does not have loose or damaged parts. If it is necessary, do these steps/instructions:
• Replace the damaged parts.
• Tighten the bolts.
• Speak to a person of an approved service center.
• Store the machine in a dry area.
• Make sure that children cannot come near the machine.

5.5 STAND THE MACHINE ON END

Figure 12.

1. Remove the grass catcher.
2. Pull and turn the handle knobs 90°.
3. Fold down the handle.
4. Turn the handle knobs 90^ to lock the handle into position.
5. Stand the machine on end and make sure that the brackets touch the floor.

Storage Switch

The machine has a storage switch that prevents its startup in the storage position.

It is necessary to remove the safety key and the battery pack to prevent accidental startup or unapproved use.

The storage switch does not replace this function.

6 TROUBLESHOOTING

* If you cannot find the solution to these problems, go to the service center.

Problem Possible	cause Solution
The handle is not in position.	The bolts are not engaged correctly.	Adjust the height of the handle and make sure that the knobs and bolts are aligned correctly.
The machine does not start.	The battery capacity is low.	Charge the battery pack.
	The bail switch is defective.	Replace the bail switch.
	The battery key is not put in.	Put in the battery key.
The machine cuts grass unevenly.	The lawn is rough.	Examine the mowing area.
	The blade height is not set correctly.	Move the wheels to a higher position.
The machine does not mulch correctly.	Wet grass clippings attach to the deck.	Wait until the grass dries before mowing.
	The mulch plug is missing.	Install the mulch plug.
The machine is hard to push.	The grass is too tall, or the blade height is too low.	Increase the blade height.
	The grass catcher and the blade drags in thick grass.	Empty the grass clippings from the grass catcher.
Problem Possible	caused Solution	Solution
There is a high vibration in the machine.	The blade is un-balanced and worn.	Replace the blade.
	The engine shaft is bent.	1. Stop the engine.2. Remove the safety key and battery pack.3. Disconnect the power source.4. Inspect for damage.5. Repair the machine before you start it again.
The machine stops during mowing.	The blade height is too low.	Increase the blade height.
	The battery pack is out of power.	Charge the battery pack.
	The grass clippings attach to the deck or the blade.	Remove the battery pack and check the deck.
	Operation temperature of the machine is too high.	Cool the machine.

7 TECHNICAL DATA

Voltage 60 V
No load speed 4000 / min
Cut width 610 mm
Cut height 25 - 80 mm
Self-propelled speed 0.5 - 1.5 m/s
Grass catcher capacity 60 L
Weight (without battery pack)	32.5 kg
Measured sound pressure level	L_pA = 71.48 dB(A)
Measured sound power level	L_wA = 91.48 dB(A)

Guaranteed sound power level	L_wA.d = 93.18 dB(A)
Vibration < 2.5 m/s	^2, K = 1.5
Battery model P60B2/P60B4/P60B6
Charger model P60UC

8 WARRANTY TY

(The full warranty terms and conditions can be found on Powerworks webpage)

The Powerworks warranty is 3 years on the product, and 2 years on batteries (consumer/private usage) from the date of purchase. This warranty covers manufacturing faults. A faulty product under warranty might be either repaired or replaced. A unit that has been misused or used in other ways then described in the owner's manual might be rejected for warranty. Normal wear, and wear parts are not considered as warranty. The original manufacturer warranty is not affected by any additional warranty offered by a dealer or retailer.

A faulty product must be returned to the point of purchase in order to claim for warranty, together with the proof of purchase (receipt).

9 EC DECLARATION OF CONFORMITY

Name and address of the manufacturer:

Name: Changzhou Globe Co., Ltd.

Address: No. 65 (3-4) Xinggang Rd., Zhonglou Zone, Changzhou 213101 China.

Name and address of the person authorised to compile the technical file:

Name: Peter Söderström

Address: Propellergatan 1, 211 15 Malmö, Sweden

Herewith we declare that the product

Category: Lawn mower

Model: LMC406

Serial number: See product rating label

Year of Construction: See product rating label

- is in conformity with the relevant provisions of the Machinery Directive 2006/42/EC.

- is in conformity with the provisions of the following other EC-Directives:

• 2014/30/EU (EMC-Directive)

• 2000/14/EC (Noise Directive) incl. modifications(2005/88/EC)

Furthermore, we declare that the following (parts/clauses of) European harmonised standards have been used:

• EN 60335-1, EN60335-2-77; EN 62233, EN ISO 3744; EN 55014-1; EN 55014-2, ISO 11094

Measured sound power level: 91.48 dB(A)

Guaranteed sound power level: 93.18 dB(A)

Conformity assessment method to Annex VI Directive 2000/14/EC.

EC type approval to 2000/14/EC: SGS United Kingdom Limited (0890).

Place, date: Changzhou, 20171207

Signature: Ted Qu, Quality Director

Ted Au

Deutsch

DE

3.3 OBEREN GRIFF MONTIEREN

Abbildung 3.

Adresse: No. 65 (3-4) Xinggang Rd., Zhonglou Zone, Changzhou 213101 China.

Adresse : No. 65 (3-4) Xinggang Rd., Zhonglou Zone, Changzhou 213101 Chine.

• 2000/14/CE (Directive Bruit) modifications includes (2005/88/CE)

Adres: No. 65 (3-4) Xinggang Rd., Zhonglou Zone, Changzhou 213101 China.

4.5 TÖMMA GRÄSUPPSAMLAREN

Figur 9.

Adress: No. 65 (3-4) Xinggang Rd., Zhonglou Zone, Changzhou 213101, Kina.

5.1 GENERELT VEDLIKEHOLD

Adresse: No. 65 (3-4) Xinggang Rd., Zhonglou Zone, Changzhou 213101, Kina.

5.3 CSERÉLJE KI A KÉST

1. • 1. ábra

FIGYELMEZTETÉS

Adres: No. 65 (3-4) Xinggang Rd., Zhonglou Zone, Changzhou 213101 Çin.

7 TEHNEHSED ANDMEDIED

Aadress: No. 65 (3-4) Xinggang Rd., Zhonglou Zone, Changzhou 213101, Hiina.