Twee Go - Breast pump Lionelo - Free user manual and instructions

USER MANUAL Twee Go Lionelo

8‑ 4 ‑EN IMPORTANT Keep this manual for future reference.

Do not repair or modify the device. Only an authorized service technician is allowed to perform these operaons.

This device is not a toy. Do not let children play with it. Keep the device out of reach of children. Cleaning and maintenance must not be performed by children if unaended.

3. The device may be used by children aged at least

8 and persons with limited physical, sensory or mental capabilies, as well as persons who lack relevant knowledge and experience in using the device as long as their acons are supervised or they have been instructed on safe use of the device and related risks beforehand.

Do not start the device if you have noticed any damage. This applies to the device and its accessories, e.g. USB cable.

Do not use the device when it starts acng up, has been dropped or immersed in water, overheats extensively, is discolored or deformed, and when other atypical circumstances occur. Contact the manufacturer’s authorized service center.

6. Never leave the plugged device unaended.

Use the device away from sources of heat, high temperatures, hot surfaces, direct sunlight, sources of ignion, naked ame, oils and sharp edges. EN‑ 5 ‑ EN

8. Do not use chemicals to clean the device. Do not

wash the main body and motor with water.

Do not immerse the enre device in water or other liquids. Do not use near water.

11. Do not disinfect the device with a steam sterilizer.

Do not use the device at variance with intended use.

Do not use the device and do not touch the power cable if your hands are wet.

14. Before cleaning or moving the device, switch it o

15. Before and aer use, wash and disinfect all pieces

which will adhere to the body and come into direct contact with milk.

16. Carefully dry every piece before use.

Do not use a tube which links the main motor with breast pump T-connecon unless you have applied the silicone membrane beforehand. The tube does not need to be disinfected.

For hygiene-related reasons, the device must be used by one person.

If use of the breast pump causes discomfort or pain, stop using the device immediately.

20. Do not use the device throughout pregnancy.

21. Do not use the device if you are red or if you are

22. If milk does not come out of the breast for more

than 5 minutes while you are using the product, stop using the breast pump and contact your doctor.‑ 6 ‑EN The product complies with requirements of EU direcves. Pursuant to the Direcve 2012/19/EU, this product is subject to selecve collecon. The product must not be disposed of along with domesc waste since it may pose a threat to the environment and human health. Worn-out product must be handed over to the electrics and electronics recycling point. Device outline (g. 1) Touch screen outline (g. 2) Breast pump modes (g. A)

1. Milk smulaon mode – 5 levels. Massage smulates inial child sucon

phase while breaseeding.

2. Milk drawing mode – 9 levels. This mode smulates deeper child sucon

phase while breaseeding. How to install

1. Posion the silicone funnel (2) on the breast pump T-connecon (3). Make

sure the funnel ange is properly aached (g. 3).

2. Place the silicone membrane (5) on the breast pump T-connecon (3). Make

sure the membrane ange is properly aached (g. 4), and then put the membrane cover (4) on.

3. Insert the sucon valve (6) into the lower hole of the breast pump T-connecon

(3). Make sure the valve is pushed as fast as possible. Note: insert the sucon valve gently to avoid damage. Do not use the valve (g. 5) if it is damaged.

6. Milk drawing mode

4. Screw the milk bole (7) to the breast pump T-connecon (3). Insert the

tube (9) into the hole in the membrane cover. Connect the membrane cover to the main motor (8) with the use of the tube (g. 6). Make sure the tube is ght to prevent air from escaping.

5. If you want to keep milk for future use, screw the adapter (12) to the milk bag

(13), and then screw everything to the breast pump T-connecon and connect T-connecon to the main motor (8) with the use of the tube (9) (g. 7).

6. To connect the double breast pump, retake the aforesaid installaon acvies

with the second set and connect tubes to the main device with the use of the connector (g. 8). How to use NOTE Before use, make sure the breast pump has been properly installed and all its pieces which come into contact with milk are disinfected. Wash hands. While using, press the breast pump against the breast ghtly to avoid air sucon.

1. Switch the device on, short press the on/o switch. The device will acvate

milk smulaon mode (massage) automacally.

2. The mode ends automacally aer 3 minutes. You can also change the mode

manually before 3 minutes expires. To do so, press the mode switching key (g. 2).

3. The milk smulaon mode: 5 levels are available. You can change massage

level by pressing level up or down keys (g. 2).

4. Milk drawing mode: 9 levels are available. You can change the sucon level

by pressing level up or down keys (g. 2). Selecon of a suitable and comfortable level is very individual and depends on the sucon power. It is advisable to use the breast pump in the milk drawing mode directly aer the milk smulaon mode. The device deacvates automacally aer a default working me: 30 minutes. How to store and heat up milk How to store

1. Aer collecng milk, ghtly close the container and put inside the fridge.

2. Milk can be stored for up to 4 hours in the room temperature (16-29°C).

3. Milk can be stored for up to 48 hours in the fridge (4°C).

4. Milk can be stored for up to 3 months in the freezer (< -4°C ).

How to heat up Aer defrosng or taking out of the fridge, use the heater to heat the milk and serve for feeding. Do not use a microwave or boiling water to heat it up because‑ 8 ‑EN milk may lose its nutrional properes. NOTE

1. To freeze milk, make sure ¾ of the container is lled because frozen milk expands.

2. To maintain nutrional values of the milk while defrosng, at rst place

the milk in the fridge, and then heat up with warm water at the maximum temperature of 37°C.

3. Do not use microwave or boiling water to defrost milk to avoid loss of

4. Never try to freeze milk again if it has already been defrosted.

5. Never add fresh milk to frozen milk.

6. Before you start breaseeding, gently shake the milk container to mix it properly.

1. The breast pump has a built-in baery.

2. When the baery is low, baery symbol will show one bar. In such case it

is advisable to charge the device.

3. Connect USB cable to breast pump USB power supply and the other p to

the USB power adapter (not supplied).

4. When the baery is full, baery symbol glows and shows three bars.

5. You can use the breast pump while charging the baery, but please remain

very careful. Troubleshoong Problem Soluon Device does not work • Check baery status

• Start charging the device

• Make sure the device has been correctly connected to charging source Insucient sucon power

• Make sure the sucon valve is correctly installed

• Place the valve in boiling water, leave for 3 minutes and then x again

• Make sure baery level is sucient

• Make sure the breast pump adheres to the breast ghtly

• When temperature in the room is lower than 15°C, leave the working device for about 30 seconds before you start using it. Pain or discomfort • Adjust massage/sucon level

• Change posion or locaon of the breast

• In case the pain or discomfort does not subside, contact your doctor How to clean and disinfect

1. Aer use, disassemble the breast pump and clean the main device with a dry

and so cloth.‑ 9 ‑ EN | PL

2. Before rst use, disinfect all pieces which will come into contact with milk

(milk bole, T-connecon, valve, membrane and silicone funnel).

3. To disinfect, put all pieces into boiling water for 10 minutes. Make sure all

pieces are immersed in water and none of them touches a dry part of the vessel, because these pieces may melt.

4. Before another use, wash all pieces under running water in order to remove

5. The tube must be completely dry before use – moisture may be sucked into

the main device and cause damage.

6. Leave all pieces on a clean cloth or dish drainer unl they go dry completely.

2. Imbuto in silicone