AD 1044 - Safe ADLER - Free user manual and instructions

USER MANUAL AD 1044 ADLER

GENERAL SAFETY CONDITIONS IMPORTANT SAFETY

INSTRUCTIONS FOR USE

READ CAREFULLY AND KEEP FOR FUTURE REFERENCE 1.Before using the device, read the instruction manual and follow the instructions contained therein. The manufacturer is not responsible for damages caused by using the device contrary to its intended use or improper operation. 2.Be especially careful when using the device when children are around. Do not allow children to play with the device do not allow children or persons not familiar with the device to use it. 3.Before using it for the first time, mount the safe in a fixed location (e.g. to the wall or floor). 4.Safes must be installed on a stable surface to avoid tipping and damage. 5.Do not install the safe in areas exposed to direct sunlight or near heat sources. 6.Safes should be installed in dry areas. 7.Do not store flammable or explosive materials or heat-generating items in the safe. 8.Change the emergency code immediately after installation. 9.Do not store the emergency key inside the safe. 10.Do not use the key regularly - it is only for emergency opening. 11.Regularly check the condition of the locking mechanism and keys. 12.Make sure the safe is locked properly after each use to avoid unauthorized access. 13.Keep the keys and access codes to the safe in a place that is safe and out of reach of unauthorized persons. 14.Avoid storing keys near the safe. 15.Do not make modifications to the safe's construction, as this may affect its strength and functionality. 16.In case of damage, use the manufacturer's authorized service. PRODUCT DESCRIPTION AD 1044 Safe with pull-out drawer and touch panel 1.safe body

10.2 x emergency key

11. 2 x mounting screw

12.external power supply 13.external power supply socket INITIAL START-UP (a) The safe's door is open by default. b) Remove the battery compartment cover located on the inside of the door. c) Insert 4 x 1.5V AA-type batteries (not included) into the battery compartment. (See "Replacing the batteries"). d) The safe is ready for operation. OPENING MODES 1.Fingerprint 2.Digital password (2-10 digits) 3.Fingerprint + password OPENING THE DOOR WITH A PASSWORD OR FINGERPRINT Touch the touch panel, the backlight will turn on. Enter a password of 2-10 digits and confirm with the "#" button. "OPEN" will appear on the screen, the drawer will slide out automatically. Place your registered finger directly on the fingerprint sensor, the blue light will turn on, wait for the fingerprint light to turn green, the drawer will automatically eject.

OPENING THE DOOR WITH PASSWORD + FINGERPRINT

Enter a password of 2-10 digits, confirm with the "#" button and then enter your fingerprint. You can also enter your fingerprint first and then enter the digital password.

CHANGING YOUR PERSONAL CODE

(initial password is 1234, no stored fingerprint) Press the "*" button for 2 seconds. "SET" will be displayed on the screen. Enter the initial password 1234 or the password you set, press the "#" button to confirm. (If the electronic lock is in password + fingerprint mode, then a valid fingerprint must be entered in addition). Press the "0" button to switch the menu, the screen will display "SET- PD", press "#" to confirm. The screen displays "BEGIN", enter a new password, press the "#" button to confirm (the password can be 2 to 10 digits), the screen displays "AGAIN", enter the new password again. Press the "#" button to confirm, "DONE" appears on the screen, indicating successful operation. (The passwords entered the first and second time must be the same. Otherwise, an error message will appear). CHANGE FINGERPRINT After opening the door with your fingerprint, press the red button, you will hear a beep, the fingerprint backlight will light up blue put your finger on it, after the beep, take your finger away. Repeat the input 3 times. The green light will illuminate, indicating successful data entry. If the fingerprint registration fails, the red light will light up, the buzzer will ring three times, indicating that the registration must be done again. A maximum of 100 fingerprints can be registered.

CHANGING THE DOOR OPENING MODE

When the door is open, hold down the "*" button for 2 seconds to enter the menu. Enter the correct password and confirm it with the "#" button and/or enter the registered fingerprint. Press the "0" button until "SET-OP" is displayed on the screen. Confirm with the "#" button. The message F-OR-P will appear on the screen - this means that the door opening mode is selected by password or fingerprint. Press the "0" button again to switch the mode. The screen will display the message F-AD-P - this means selecting the mode of opening the door by password and fingerprint. When one of the two methods is selected, press the "#" button to confirm it.

SETTING THE VIBRATION ALARM

When the door is open, hold down the "*" button for 2 seconds to enter the menu. Enter the correct password and confirm it with the "#" button and/or enter the registered fingerprint. Press the "0" button until "SET-AL" is displayed on the screen. Confirm with the "#" button. Switch modes with the "0" button to set:5 - AL-1: Vibration level is level 1 - the lowest sensitivity - AL-2: Vibration level is level 2 - AL-3: Vibration level is level 3 - AL-4: Vibration level is level 4 - AL-5: Vibration level is level 5 - the highest sensitivity - AL-ON - alarm on - AL-OFF - alarm off DATA CLEANING Fingerprint deletion Open the door of the safe. Press the red button located on the inside of the door for 4 seconds, the buzzer will ring twice. At this moment you can let go of the red button. The fingerprint has been successfully removed.

HOW TO REMOVE, REPLACE BATTERIES

Open the container, take out the used batteries. To properly insert new batteries, pay special attention to the polarity (+) plus and (-) . There is a graphic symbol inside or around the battery container, which illustrates how to correctly place the batteries in the container, then close the battery container. Important safety information Improper use of batteries can cause electrolyte leakage, overheating or explosion. Released electrolyte is a source of corrosion and can be toxic. It can cause skin and eye burns; it is also harmful if swallowed. To reduce the risk of injury: -Keep batteries out of the reach of children. -Batteries should not be heated, opened, punctured, destroyed, or thrown into a fire, and should not be inserted in reverse into the device. Pay special attention to the [+] and [-] markings. -Do not use old and new batteries at the same time, or batteries of different types ( for example, carbon-zinc and alkaline). -Do not touch the battery terminals in the device with metal objects. These components can get hot and cause burns. -Remove the batteries from the device if the batteries are worn out or if the device is to be stored for a long time. -Old depleted or used batteries should be removed from the device and sent for disposal or recycling in accordance with national waste disposal regulations. -In case of battery leakage, remove all batteries, avoiding contact of the leaking electrolyte with skin or clothing. If battery electrolyte comes into contact with skin or clothing, immediately flush the area with water. Before inserting new batteries, clean the battery compartment thoroughly with a damp paper towel. Note -Replacing the battery with the wrong type may cause an explosion. Use only batteries of the same size and type. -Do not recharge ordinary batteries ! TECHNICAL SPECIFICATIONS:

EXTERNAL DIMENSIONS: 200 x 450 x 405mm INTERNAL DIMENSIONS: 190 x 400 x 365mm POWER: 4 x AA 1.5V batteries (not included)

For the sake of the environment. Information about waste electrical and electronic equipment In accordance with Article 13(1) and (2) of the Law of September 11, 2015 on waste electrical and electronic equipment, we inform you about the proper handling of waste electrical and electronic equipment: 1. It is forbidden to place waste electrical and electronic equipment together with other waste - this is confirmed by marking in the form of a "crossed out basket", ordering selective collection of this type of waste. 2. Electrical and electronic equipment may contain hazardous substances, mixtures and components that, when released into the environment, can cause serious danger to the health and life of humans and living organisms. They can lead to numerous health ailments, such as vision, hearing and speech disorders, and can also damage the kidneys, liver and heart, and cause skin diseases. Harmful substances, can also have adverse effects on the respiratory and reproductive systems and lead to cancerous changes. Consumption of plants growing on contaminated soils, and products made from them, can risk the aforementioned health effects. 3. Waste electrical and electronic equipment should be handed over only to authorized collection points, a list of which should be included on each Municipality's website. 4. The household plays an important role, in contributing to the reuse and recovery, including recycling, of waste equipment. It also plays a6 key role in the waste electrical and electronic equipment management system due to the possibility of direct delivery to authorized collection points and the elimination of undesirable social habits resulting in leaving waste equipment in places not intended for it. In addition, Donate waste electrical and electronic equipment at the point of delivery. A distributor, when supplying equipment intended for households to a purchaser, is obliged to take back used household equipment free of charge at the place of delivery of such equipment, provided the used equipment is of the same type and performed the same functions as the supplied equipment. Cardboard packaging and polyethylene (PE) bags should be placed in the appropriate containers for separate collection of municipal waste according to their description. If there are batteries in the equipment, remove them and separately dispose of them at a collection and storage facility. Do not dispose of the device in the municipal waste container!!! Service If you wish to purchase spare parts or report any complaints, please contact directly with the seller who issued the receipt. Bedienungsanleitung (DE)