Studio PAR 64 - Lighting Cameo - Free user manual and instructions

USER MANUAL Studio PAR 64 Cameo

ENGLISHDEUTSCHFRANCAIS FRANCAISFRANCAIS FRANCAISFRANCAIS ESPAÑOLPOLSKIITALIANO Thank you for choosing Cameo Lights! We have designed this product to give you reliable operation over many years. Please, take a few moments to read these instructions carefully, as we want you to enjoy your new Cameo Lights products quickly and to the fullest. Further information about Cameo Lights check our website WWW.CAMEOLIGHT.COMSTUDIO PAR 64 LED CAN 12 X 12 W 6-IN-1 LED RGBWA+UV PAR PROJECTOR

1. Please read these instructions carefully.

2. Keep all information and instructions in a safe place.

3. Follow the instructions.

4. Observe all safety warnings. Never remove safety warnings or other information from the equipment.

5. Use the equipment only in the intended manner and for the intended purpose.

6. Use only sufficiently stable and compatible stands and/or mounts (for fixed installations). Make certain that wall

mounts are properly installed and secured. Make certain that the equipment is installed securely and cannot fall down.

7. During installation, observ e the applicable safety regulations for your country.

8. Never install and operate the equipment near radiators, heat registers, ovens or other sources of heat. Make

certain that the equipment is always installed so that is cooled sufficiently and cannot overheat.

9. Never place sources of ignition, e.g., burning candles, on the equipment.

10. Ventilation slits must not be blocked.

11. Do not use this equipment in the immediate vicinity of water (does not apply to special outdoor equipment -

in this case, observe the special instructions noted below. Do not expose this equipment to flammable materials, fluids or gases.

12. Make certain that dripping or splashed water cannot enter the equipment. Do not place containers filled with

liquids, such as vases or drinking vessels, on the equipment.

13. Make certain that objects cannot fall into the device.

14. Use this equipment only with the accessories recommended and intended by the manufacturer.

15. Do not open or modify this equipment.

16. After connecting the equipment, check all cables in order to prevent damage or accidents, e.g., due to

17. During transport, make certain that the equipment cannot fall down and possibly cause property damage and

18. If your equipment is no longer functioning properly, if fluids or objects have gotten inside the equipment or

if it has been damaged in anot her way, switch it off immediately and unplug it from the mains outlet (if it is a powered device). This equipment may only be repaired by authorized, qualified personnel.

19. Clean the equipment using a dry cloth.

20. Comply with all applicable disposal laws in your country. During disposal of packaging, please separate

plastic and paper/cardboard.

21. Plastic bags must be kept out of reach of children.

FOR EQUIPMENT THAT CONNECTS TO THE POWER MAINS:

22. CAUTION: If the power cord of the device is equipped with an earthing contact, then it must be connected to

an outlet with a protective ground. Never deactivate the protective ground of a power cord.

23. If the equipment has been exposed to strong fluctuations in temperature (for example, after transport), do

not switch it on immediately. Moisture and condensation could damage the equipment. Do not switch on the equipment until it has reached room temperature.

24. Before connecting the equipment to the power outlet, first verify that the mains voltage and frequency match

the values specified on the equipment. If the equipment has a voltage selection switch, connect the equipment to the power outlet only if the equipment values and the mains power values match. If the included power cord or power adapter does not fit in your wall outlet, contact your electrician.

25. Do not step on the power cord. Make certain that the power cable does not become kinked, especially at the

mains outlet and/or power adapter and the equipment connector.

26. When connecting the equipment, make certain that the power cord or power adapter is always freely

accessible. Always disconnect the equipment from the power supply if the equipment is not in use or if you want4 5 ITALIANO POLSKI ESPAÑOL FRANCAIS FRANCAIS FRANCAIS FRANCAIS FRANCAIS DEUTSCH ENGLISH SAFETY: to clean the equipment. Always unplug the power cord and power adapter from the power outlet at the plug or adapter and not by pulling on the cord. Never touch the power cord and power adapter with wet hands.

27. Whenever possible, avoid switching the equipment on and off in quick succession because otherwise this

can shorten the useful life of the equipment.

28. IMPORTANT INFORMATION: Replace fuses only with fuses of the same type and rating. If a fuse blows repea-

tedly, please contact an authorised service centre.

29. To disconnect the equipment from the power mains completely, unplug the power cord or power adapter

from the power outlet.

30. If your device is equipped with a Volex power connector, the mating Volex equipment connector must be

unlocked before it can be removed. However, this also means that the equipment can slide and fall down if the power cable is pulled, which can lead to personal injuries and/or other damage. For this reason, always be careful when laying cables.

31. Unplug the power cord and power adapter from the power outlet if there is a risk of a lightning strike or

before extended periods of disuse. CAUTION

RISK OF ELECTRIC SHOCK

CAUTION: Never remove the cover, because otherwise there may be a risk of electric shock. There are no user serviceable parts inside. Have repairs carried out only by qualified service personnel. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electrical shock. The exclamation mark within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions.

CAUTION! IMPORTANT INFORMATION ABOUT LIGHTING PRODUCTS

1. Do not look into the beam from a distance of less than 40 cm.

2. Do not stare into the beam for extended periods at short-to-medium distances.

3. Do not view the beam directly with optical instruments such as magnifiers.

4. Under some circumstances, stroboscopic effects may trigger epileptic seizures in sensitive individuals! For this

reason, persons who suffer from epilepsy should always avoid places where strobe lights are used. The product has been developed for professional use in the field of event technology and is not suitable as household lighting.INTRODUCTION: 12 x 12 W 6-in-1 LED RGBWA+UV STUDIO PAR PROJECTOR

• 2-channel, 3-channel 1, 3-channel 2, 6-channel and 9-channel DMX control

• red, green, blue, white, amber and UV separately controllable FEATURES:

• 12 X 12 W 6-in-1 LEDs

• Power consumption 55 W

• Music control via built-in microphone

• Colour change rate and stroboscope effect controllable via control panel and DMX OPERATION: The Cameo CLPST64RGBWAU12W is a DMX-512 controllable LED lighting system with RGBWAU colour mixing that excels due to highly efficient, extra bright LEDs. The intensity of the six colour groups (red, green, blue, white, amber, UV) can be controlled independently of one another, thus permitting an unlimited number of different colours. The Cameo LED light can can be used both individually and in master/slave mode, with music control, and via DMX-512 protocol. CONTROLS AND INDICATORS:

DMX IN 3-pin XLR socket for connection of a DMX controller (e.g., DMX mixer).

DMX OUT 3-pin XLR socket for looping through the DMX control signal.

POWER OUT Neutrik powerCON power output socket. Used to supply power to additional CAMEO projectors. Make sure that the total current consumption in amperes (A) of all connected devices does not exceed the specified value on the device.

FUSE HOLDER IMPORTANT INFORMATION: Replace the fuse only with a fuse of the same type and rating. If the fuse blows repeatedly, please contact an authorised service centre.

MODE Selection of the standalone functions, DMX modes, and DMX address.

ENTER Makes it possible to change a value and confirm changes.

Press the UP and DOWN buttons, for example, to change the microphone sensitivity, stroboscope speed or DMX address.

Displays the operating mode and values of individual functions. The illumination of the LC display switches off automatically after approx. 70 seconds of inactivity. Pressing any one of the 4 control buttons will turn the illumination of the LC display on again.

Overhead installation may only be carried out by trained personnel. The spotlight must be secured with an appropriate safety cable to prevent falling.

9 10OPERATION: NOTE: When the projector is properly connected to the mains, the following information appears successively in the display during the startup process: "Software Update, Please Wait..." (for service purposes only), the software version "Software V1.xx" and "WELCOME TO cameo". After this operation, the projector is ready for use and changes to the mode that was previously selected. STATIC COLOUR This mode offers the ability to separately adjust the intensity for each of the 6 LED groups and to generate an unlimited number of different colours (colour mixing). Press the MODE button until "STATIC" appears in the upper line of the display. By repeatedly pressing the ENTER button, select the LED group for which you want to change the brightness level (please note the cursor in the display, Rxx = red, Gxx = green, Bxx = blue, Wxx = white, Axx = amber, UVxx = UV / black light). Now you can set the intensity of the selected light from 00 to 99 using the UP and DOWN buttons (example: R00 = red at 0%, i.e. out. R99 = red at 100%, i.e. maximum brightness). Adjust the flash frequency of the strobe effect by pressing ENTER repeatedly until the cursor shows "Fxx". Now you can activate the strobe effect using the UP and DOWN buttons and set the flash frequency from 00 to 99 (F00 = strobe effect deactivated, F01 = approx. 1 Hz, F99 = approx. 20 Hz). Confirm with ENTER. RED Intensity R00 - R99 GREEN Intensity G00 - G99 BLUE Intensity B00 - B99 WHITE Intensity W00 - W99 AMBER Intensity A00 - A99

ENGLISHDEUTSCHFRANCAIS FRANCAISFRANCAIS FRANCAISFRANCAIS ESPAÑOLPOLSKIITALIANOOPERATION: COLOUR MACROS In this mode, one of the 6 basic colours of the projector or one of the 9 different mixed colours can be selected as a preset. Press the MODE button until "MACRO" appears in the upper line of the display. Now press ENTER and then select one of the 15 colour presets using the UP and DOWN buttons. Confirm with ENTER. MACRO 01 = red MACRO 09 = lavender MACRO 02 = green MACRO 10 = light green MACRO 03 = blue MACRO 11 = magenta MACRO 04 = white MACRO 12 = turquoise MACRO 05 = amber MACRO 13 = orange MACRO 06 = UV / black light MACRO 14 = cool white MACRO 07 = yellow MACRO 15 = warm white MACRO 08 = cyan COLOUR CHANGE In the colour change mode (Jumping Mode), 12 different colours alternate in rapid succession (red, green, blue, white, amber, yellow, cyan, lavender, pink, light green, magenta, turquoise, orange). The speed of the program is adjustable separately and a stroboscope effect can also be activated. Press the MODE button until "JUMPING" appears in the upper line of the display. Now, press ENTER until the cursor appears in the lower line of the display, and then select the rate (SPEED) using the UP and DOWN buttons, with the colours alternating from 00 to 99. Confirm with ENTER. The indicator in the bottom line of the display changes to "FLASH:xx". At the same time, the cursor will appear in the bottom line and you can activate the stroboscope effect using the UP and DOWN buttons and adjust the flash frequency from 00 to 99 (FLASH:00 = strobe deactivated, FLASH: 01 = approx. 1 Hz, FLASH: 99 = approx. 20 Hz). Confirm with ENTER. COLOUR CHANGE Rate SPEED:00 - SPEED:99 STROBOSCOPE Flash frequency FLASH:00 - FLASH:99

ITALIANO POLSKI ESPAÑOL FRANCAIS FRANCAIS FRANCAIS FRANCAIS FRANCAIS DEUTSCH ENGLISHOPERATION: COLOUR BLENDING In the colour fade mode (fading mode) different colours are blended into one another in succession. The speed of the program is adjustable separately and a stroboscope effect can also be activated. Press the MODE button until "FADING" appears in the upper line of the display. Now, press ENTER until the cursor appears in the lower line of the display, and then select the rate (SPEED) using the UP and DOWN buttons, with the colours alternating from 00 to 99. Confirm with ENTER. The indicator in the bottom line of the display changes to "FLASH:xx". At the same time, the cursor will appear in the bottom line and you can activate the stroboscope effect using the UP and DOWN buttons and adjust the flash frequency from 00 to 99 (FLASH:00 = strobe deactivated, FLASH: 01 = approx. 1 Hz, FLASH: 99 = approx. 20 Hz). Confirm with ENTER. COLOUR BLENDING Rate SPEED:00 - SPEED:99 STROBOSCOPE Flash frequency FLASH:00 - FLASH:99 AUTO MODE Press the MODE button repeatedly until "AUTO MODE" appears on the display. In this operating mode, the light switches automatically between colour change and colour blending mode. The colour change and/or colour blending rate is determined by the settings of the respective mode. A stroboscopic effect cannot be activated. SLAVE MODE Press the MODE button repeatedly until "SLAVE MODE" appears on the display. Connect the slave and the master unit (same model) with a DMX cable. Now the slave unit follows the master unit.

ENGLISHDEUTSCHFRANCAIS FRANCAISFRANCAIS FRANCAISFRANCAIS ESPAÑOLPOLSKIITALIANOOPERATION: MUSIC CONTROL Press the MODE button until "SOUND" appears in the upper line of the display. Now the projector is controlled by the built-in microphone and follows the beat of the music. To adjust the microphone sensitivity, press ENTER, and the cursor appears in the lower line of the display (SENS:xx) and use the UP and DOWN buttons to set the desired value from 00 to 31 (SENS:00 = minimum sensitivity, SENS:31 = maximum sensitivity). Confirm with ENTER.

Press the MODE button repeatedly until "DMX MODE" appears in the upper line of the display. Press ENTER, and the cursor appears in the lower line of the display and then use the UP and DOWN buttons to select one of the five DMX modes (02CH, 03CH1, 03CH2, 06CH, 09CH). Confirm with ENTER. You will find tables with the channels of the different DMX modes on the following pages of this manual.

Press the MODE button repeatedly until "DMX ADDR" appears in the upper line of the display. Press ENTER, and the cursor appears in the lower line of the display and then use the UP and DOWN buttons to select the desired DMX start address between 001 and 512. Confirm with ENTER. NOTE: The illumination of the LC display switches off automatically after approx. 70 seconds of inactivity. Pressing any one of the 4 control buttons will turn the illumination of the LC display on again.

151 - 220 Colour Blending (rate)

151 - 220 Colour Blending (rate)

ITALIANO POLSKI ESPAÑOL FRANCAIS FRANCAIS FRANCAIS FRANCAIS FRANCAIS DEUTSCH ENGLISH16 17 ENGLISHDEUTSCHFRANCAIS FRANCAISFRANCAIS FRANCAISFRANCAIS ESPAÑOLPOLSKIITALIANO DMX CONNECTION: DMX-512 DMX (Digital Multiplex) is the name of a universal transmission protocol for communication between corresponding devices and controllers. A DMX controller sends DMX data to the connected DMX device(s). The DMX data is always transmitted as a serial data stream that is forwarded from one connected device to the next via the "DMX IN" and "DMX OUT" connectors (XLR plug-type connectors) that are found on every DMX-capable device. (Most controllers only have a DMX output.) DMX CONNECTION: DMX is the common "language" via which a very wide range of types and models of equipment from various manufacturers can be connected with one another and controlled via a central controller, provided that all of the devices and the controller are DMX-compatible. For optimum data transmission, it is necessary to keep the connecting cables between the individual devices as short as possible. The order in which the devices are integrated in the DMX network has no influence on addressing. Thus the device with the DMX address 1 can be located at any position in the (serial) DMX chain: at the beginning, at the end or somewhere in the middle. If the DMX address 1 is assigned to a device, the controller "knows" that it should send all data allocated to address 1 to this device regardless of its position in the DMX network. The Adam Hall 3 STAR, 4 STAR, and 5 STAR product ranges include an extensive selection of suitable cables.

SERIAL CONNECTION OF MULTIPLE LIGHTS

1.) Connect the male 3-pole XLR connector of the DMX cable to the DMX output (female 3-pole socket) of the first light or other DMX device. 2.) Connect the female 3-pole connector of the DMX cable connected to the first light to the DMX input (male 3-pole socket) of the next DMX device. In like manner, connect the DMX output of this device to the DMX input of the next device and repeat until all devices have been connected. Please note that as a rule, DMX devices are connected in series and connections cannot be shared without active splitters.16 17 ITALIANO POLSKI ESPAÑOL FRANCAIS FRANCAIS FRANCAIS FRANCAIS FRANCAIS DEUTSCH ENGLISH DMX CABLE: NOTE:

• When fabricating your own cables, always observe the illustrations on this page. Never connect the shielding of the cable to the ground contact of the plug, and always make certain that the shielding does not come into contact with the housing of the XLR plug. If the shielding is connected to ground, this can lead to short-circuiting and system malfunctions. PLEASE NOTE: TERMINATION:

• With extended cable runs, the last device in the chain may require a terminating resistor in order to prevent system malfunctions. This is achieved by using a cable terminator module (Product No. K3DMXT3).

• Some manufacturers use 5-pole versions for data transmission instead of 3-pole XLR plugs. However, devices with 5-pole XLR connectors can also be integrated in a DMX network with 3-pole XLR connectors. In this case, a suitable cable adapter is required. The following illustration shows the correct pin-out of the corresponding plugs. Use of a terminating resistor (termination) reduces interference and other problems during signal transmission. It is always advisable to connect a DMX termination module (resistance 120 ohms, 1/4 W) between pole 2 (DMX-) and pole 3 (DMX+) of the last device in the chain. Usual connection DMX-512 output 3-pole XLR DMX-512 input 3-pole XLR 5-pole XLR(socket)Pole 1: Ground (shielding)Pole 2: Signal (-)Pole 3: Signal (+)Pole 4: unusedPole 5: unused5-pole XLR(socket)Pole 1: Ground (shielding)Pole 2: Signal (-)Pole 3: Signal (+)Pole 4: unusedPole 5: unused3-pole XLR(socket)Pole 1: Ground (shielding)Pole 2: Signal (-)Pole 3: Signal (+)3-pole XLR(socket)Pole 1: Ground (shielding)Pole 2: Signal (-)Pole 3: Signal (+)SPECIFICATIONS: Model Name: CLPST64RGBWAU12W Product Type: LED PAR can Type: PAR 64 Can Colour Spectrum: RGBWA+UV Number of LEDs: 12 LED Type: 12 W 6-in-1 Refresh Rate: 3000 Hz Dispersion Angle: 25° DMX Input: 3-pin XLR male DMX Output: 3-pin XLR female DMX Mode: 2-channel, 3-channel 1, 3-channel 2, 6-channel, 9-channel DMX Functions: colour change, colour blending, music control, stroboscope, RGBWAU Standalone Functions: colour change, colour blending, music control, stroboscope, static colours, colour macros, master/ slave operation Controls: Mode, Enter, Up, Down Indicators: lit LC Display Operating Voltage: 100 - 240 V AC / 50 - 60 Hz Power Consumption: 55 W Power Connector: Neutrik powerCON input and output Fuse: F2AL / 250 V Housing Material: cast metal Housing Colour: black Housing Cooling: fan Dimensions (W x H x D, excluding bracket): 230 x 220 x 255 mm Weight: 4.5 kg Other Features: 1m power cable with Neutrik PowerCon and Schuko plug included, double bracket included

MANUFACTURER‘S WARRANTY

This warranty extends to the CAMEO branded product you purchased from Adam Hall. The statutory warranty rights against the vendor shall not be affected by this warranty. Rather, this warranty gives you additional independent claims against Adam Hall. With this warranty, Adam Hall ensures that products you have purchased from Adam Hall or Adam Hall partners, under normal use, are free of defects in material or workmanship for a period of 2 years from the date of purchase. The warranty period begins on the date of purchase. In order to assert a claim for warranty service, the proof of date of purchase is provided by the receipt bearing the date of purchase or the date of purchase on the delivery note. You are entitled to warranty service under the conditions and provisions set out in this document, if a repair within the warranty period is required. This warranty applies only to the original purchaser of the products supplied by Adam Hall and is not transferable to any person to whom the property is transferred by the original purchaser. Within the warranty period, the defective parts or the product from Adam Hall will be repaired or replaced. Under the terms of this warranty, all the replaced or removed components become the property of Adam Hall. In the unlikely event that a product acquired from Adam Hall, repeatedly exhibits a defect, Adam Hall may decide, at its discretion, to replace this product with a comparable product of at least the same performance. Adam Hall does not guarantee that the operation of this product will be uninterrupted or error-free. Adam Hall accepts no responsibility for any damage due to incorrect compliance with the instructions received in the delivery. This warranty does not extend to: - wearing parts (eg battery, tubes). - devices that have had their serial number removed or damaged, or failed as a result of an accident - inappropriate or abusive use or other external causes - devices that were not used in accordance with the operating parameters defined in the user documentation shipped with the product - devices that have been repaired using parts not made or distributed by Adam Hall - devices that have been serviced, modified or repaired by someone other than Adam Hall or an authorised service partner. These terms and conditions constitute the complete and exclusive warranty agreement between you and Adam Hall regarding the Adam Hall branded product you have purchased. This warranty is valid only within Europe. Outside of Europe please contact our official distributors.20 21 ENGLISHDEUTSCHFRANCAIS FRANCAISFRANCAIS FRANCAISFRANCAIS ESPAÑOLPOLSKIITALIANO MANUFACTURER´S DECLARATIONS:

LIMITATION OF LIABILITY

If your Adam Hall branded hardware product fails to work as warranted above, your sole and exclusive remedy shall be repair or replacement. Adam Halls’ maximum liability under this limited warranty is expressly limited to the lesser of the price you have paid for the product or the cost of repair or replacement of any components that malfunction under conditions of normal use. Adam Hall is not liable for any damages caused by the product or the failure of the product, including any lost profits or savings or special, incidental, or consequential damages. Adam Hall is not liable for any claim made by a third party or made by you for a third party. This limitation of liability applies whether damages are sought, or claims are made, under this Limited Warranty or as a tort claim (including negligence and strict product liability), a contract claim, or any other claim, and cannot be rescinded or changed by anyone. This limitation of liability will be effective even if you have advised Adam Hall or an authorized representative of Adam Hall of the possibility of any such damages, but not, however, in the event of claims for damages in connection with personal injuries. This manufacturer‘s warranty grants you specific rights; depending on jurisdiction (nation or state), you may be be entitled to additional claims. You are advised to consult applicable state or national laws for a full determina- tion of your rights.

REQUESTING WARRANTY SERVICE

To request warranty service for the product, contact Adam Hall or the Adam Hall authorized reseller from which you purchased the product.

EC DECLARATION OF CONFORMITY

The equipment marketed by Adam Hall complies (where applicable) with the essential requirements and other relevant specifications of Directives 1999/5/EC (R&TTE), 2004/108/EC (EMC) und 2006/95/EC (LVD). Additional information can be found at www.adamhall.com.20 21 ITALIANO POLSKI ESPAÑOL FRANCAIS FRANCAIS FRANCAIS FRANCAIS FRANCAIS DEUTSCH ENGLISH MANUFACTURER´S DECLARATIONS:

PROPER DISPOSAL OF THIS PRODUCT

(Valid in the European Union and other European countries with waste separation) This symbol on the product, or the documents accompanying the product, indicates that this appliance may not be treated as household waste. This is to avoid environmental damage or personal injury due to uncontrolled waste disposal. Please dispose of this product separately from other waste and have it recycled to promote sustainable economic activity. Household users should contact either the retailer where they purchased this product, or their local government office, for details on where and how they can recycle this item in an environmentally friendly manner. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal .

ENVIRONMENTAL PROTECTION AND ENERGY CONSERVATION

Energy conservation is an active contribution to environmental protection. Please turn off all unneeded electrical devices. To prevent unneeded devices from consuming power in standby mode, disconnect the mains plug. Adam Hall GmbH, all rights reserved. The technical data and the functional product characteristics can be subject to modifications. The photocopying, the translation, and all other forms of copying of fragments or of the integrlity of this user’s manual is prohibited.ENGLISHDEUTSCHFRANCAIS FRANCAISFRANCAIS FRANCAISFRANCAIS ESPAÑOLPOLSKIITALIANO

MISE AU REBUT DE CE PRODUIT

• diody LED 12 x 12 W 6in1