Cloud Stinger Wireless - Headphones HYPERX - Free user manual and instructions

Product Type	Wireless headset
Brand	HyperX
Model	Cloud Stinger Wireless
Color	Black
Transducer	Dynamic 50 mm with neodymium magnets
Type	Circumaural, closed back
Frequency response	20 Hz – 20,000 Hz
Impedance	32 Ω
Sound pressure level	109 dBSPL/mW at 1 kHz
Total harmonic distortion	< 2 %
Weight	270 g
Microphone	Electret condenser, noise cancelling
Microphone sensitivity	-47 dBV (0 dB=1V/Pa, 1 kHz)
Microphone frequency response	100 Hz – 7,000 Hz
Battery life	17 hours (at 50% volume)
Charging time	Approximately 2.5 hours
Wireless range	Up to 12 m (2.4 GHz)
Connectivity	Wireless USB adapter
Controls	Volume wheel, Power button, swivel microphone with automatic mute
Charging cable	USB, 1 m
Compatibility	PC, PS4, Nintendo Switch
Care and cleaning	Clean with a soft dry cloth. Do not use harsh chemicals.
Safety	Use only the supplied charger. Do not expose to moisture or extreme temperatures.
Spare parts and repairability	Wireless adapter, USB cable, ear cushions (replaceable, contact HyperX support)

Frequently Asked Questions - Cloud Stinger Wireless HYPERX

How do I charge the HyperX Cloud Stinger Wireless headset?

Plug the USB charging cable into the headset's charging port and into a USB charger. The LED charge level indicator shows the status. A full charge takes approximately 2.5 hours.

What is the battery life?

Battery life is 17 hours at 50% volume. This may vary depending on the volume level used.

How do I pair the headset with the wireless adapter?

The headset is pre-paired. For manual pairing, turn off the headset, plug in the adapter, press the adapter's PIN button for 3 seconds, then hold the headset's Power button for 10 seconds until the LEDs stay solid.

Is the headset compatible with PS4?

Yes, plug the USB adapter into a PS4 port, turn on the headset, then in PS4 audio settings, select 'USB Headset (HyperX Cloud Stinger Wireless)' for input and output, and set 'All audio' to headset.

Can I use the headset with Nintendo Switch?

Yes, plug the adapter into a USB port on the dock, turn on the headset, and adjust volume via the console then the headset wheel.

How do I mute the microphone?

Simply rotate the microphone up. The mic will automatically mute. To unmute, lower it.

What do the LED indicators on the headset mean?

The charge level indicator shows: solid green = 90-100%, blinking green = 50-90%, blinking orange = 25-50%, blinking red = <25%. During charging, solid green = charged, breathing green = 50-99%, breathing orange = 25-50%, breathing red = <25%.

How do I adjust the volume?

Use the volume wheel on the earcup. Turn towards + to increase, towards - to decrease.

Does the headset work with a PC?

Yes, plug the USB adapter, turn on the headset, then in audio settings set 'Speakers HyperX Cloud Stinger Wireless' as default playback device and 'Microphone HyperX Cloud Stinger Wireless' as default recording device.

What to do if the headset won't turn on?

Make sure the battery is charged. Plug in the USB cable and check if the LED turns on. If the issue persists, contact HyperX support at hyperxgaming.com/support/headsets.

USER MANUAL Cloud Stinger Wireless HYPERX

HyperX Cloud Stinger Wireless™ Headset

Find the language and latest documentation for your HyperX Cloud Stinger Wireless headset here.

HyperX Cloud Stinger Wireless Headset Installation Guide

For instructions in English Para instrucciones en Español Für Anleitungen in Deutsch Pour des instructions en Français ...... Per le istruzioni in Italiano Por as instruções em Português Instrukcje w języku Polskim Для инструкции на Русском C. Turkce talimatlar icin 日本語マニュアル用 한국어 안내 ......คำแนะนำภาษาไทย Đế xem hướng dẫn bằng tiếng Việt

Simplified Chinese ..... 简体中文说明书

Traditional Chinese ....繁體中文說明

HyperX Cloud Stinger Wireless™

Part numbers

HX-HSCSW-BK

TABLE OF CONTENTS

Overview....3

Specifications 4

Headset Controls....5

Headset Battery Indicator LED States....6

Headset Charging....7

Using with PS4™ 8

Using with Nintendo Switch™ 9

Using with PC....10

Manually Pairing Headset and Wireless Adapter.... 12

Overview

A. Volume wheel B. Swivel to mute microphone C. USB charge port D. Power button E. Wireless adapter F. USB charge cable G. Wireless status light H. Battery indicator LED

Specifications

Headphone

Driver: Dynamic, 50mm with neodymium magnets

Type: Circumaural, Closed back

Frequency response: 20Hz-20,000Hz

Impedance: 32 Ohm

Sound pressure level: 109dBSPL/mW at 1kHz

T.H.D.: < 2%

Weight: 270g

Cable length and type: USB charging cable (1m)

Microphone

Element: Electret condenser microphone

Polar pattern: Noise-cancelling

Frequency response: 100Hz-7,000 Hz

Sensitivity: -47dBV (0dB=1V/Pa, 1kHz)

Battery life*

17 hours

Battery charge time

About 2.5 hours

Wireless Range**

2.4 GHz

Up to 12 meters

*Tested at 50% headphone volume

**Wireless range may vary due to environmental conditions

Headset Controls

Power button

Hold the power button for 3 seconds to power on/off the headset.

Volume wheel

Move the volume wheel towards the + sign to increase the volume. Move the volume wheel towards the - sign to decrease the volume.

Microphone mute

Swivel the microphone upwards to mute the microphone.

Swivel the microphone downwards to unmute the microphone.

Headset Battery Indicator LED States

The headset battery indicator LED indicates the current state of the headset.

Battery Indicator LED	Headset Status
Slow breathing orange	Searching for wireless adapter
Fast blinking red and green	Pairing mode
Solid green	90% – 100% battery remaining
Blinking green	50% – 90% battery remaining
Blinking orange	25% – 50% battery remaining
Blinking red	<25% battery remaining

Headset Charging

When the headset is connected to a charger with the USB charge cable, the battery indicator LED will indicate the charge status. The headset will take approximately 2.5 hours to fully charge.

Battery Indicator LED	Charging Status
Solid green	100% charged
Breathing green	50% – 99% charged
Breathing orange	25% – 50% charged
Breathing red	<25% charged

Using with PS4™

1. Connect the wireless adapter to a front USB port on the PS4™ system.
2. Power on the headset.
3. When the wireless adapter status light is solid, the headset is now connected to the adapter.

To ensure the headset is configured with the most optimal settings on the PS4, follow the steps below:

1. From the PS4 main menu, go to Settings > Devices > Audio Devices
2. Set Input Device to USB Headset (HyperX Cloud Stinger Wireless)
3. Set Output Device to USB Headset (HyperX Cloud Stinger Wireless)
4. Set Output to Headphones to All Audio
5. Set Volume Control (Headphones) to 100% volume

Using with Nintendo Switch™

1. Connect the wireless adapter to a side USB port on the Nintendo Switch dock.
2. Power on the headset.
3. When the wireless adapter status light is solid, the headset is now connected to the adapter.

You may set the USB audio volume on Switch to maximum by using the volume buttons on the Switch console, then adjust the volume with the headset volume wheel.

Using with PC

1. Connect the wireless adapter to a USB port on the PC.
2. Power on the headset.
3. When the wireless adapter status light is solid, the headset is now connected to the adapter.

To ensure the headset is configured correctly on the PC, follow the steps below:

1. Right-click on the sound icon on the system tray and select Sounds.

1. On the Playback tab, right-click on Speakers HyperX Cloud Stinger Wireless and select Set as Default Device.
2. On the Recording tab, right-click on Headset Microphone HyperX Cloud Stinger Wireless and select Set as Default Device.

Manually Pairing Headset and Wireless Adapter

The headset and wireless adapter are already paired together for first time use. If manual pairing is necessary, follow the steps below to pair the headset and wireless adapter together.

1. Make sure the headset is powered off.
2. Plug the USB wireless adapter into the PC or PS4™ system.
3. Use a small pin to press the small button on the back side of the USB wireless adapter for 3 seconds. The USB wireless adapter LED will be fast blinking.

1. Long press the headset power button for 10 seconds to enter the pairing mode. The headset battery indicator LED will be fast blinking.

1. When both the USB wireless adapter LED and the headset battery indicator LED are both solid, pairing is completed.

Questions or Setup Issues?

Contact the HyperX support team at: hyperxgaming.com/support/headsets

HyperX Cloud Stinger Wireless™

Specifications

Headphones

Part numbers

HX-HSCSW-BK

CONTENTS

Overview....3

Specifications 4

Specifications

Headphones

Product references

HX-HSCSW-BK

TABLE OF CONTENTS

Overview....3

Specifications 4

Specifications

Headset

Microphone mute

Part numbers

HX-HSCSW-BK

INDEX

Technical specifications

Headphones

Part numbers

HX-HSCSW-BK

INDEX

Overview 3

Specifications

Headphone

Driver: Dynamic, 50 mm with neodymium magnets

Type: Circumaural, closed

Headset Controls

Power button

Manual pairing of headset and wireless adapter

Catalog numbers

HX-HSCSW-BK

TABLE OF CONTENTS

Overview.... 3

Specifications 4

Specifications

Headphones

Catalog numbers

HX-HSCSW-BK

CONTENTS

Overview 3

Specifications....4

Part Numbers

HX-HSCSW-BK

CONTENTS

Overview 3

Specifications 4

Specifications

Headset

Microphone mute

Part Numbers

HX-HSCSW-BK

Contents

Overview 3

Specifications 4

Headset Controls 5

A. Volume adjustment wheel

Specifications

Headphones

Microphone mute

Part number

HX-HSCSW-BK

Table of Contents

Overview 3

Specifications 4

Headset Controls 5

Sensitivity: -47dBV (0dB=1V/Pa, 1kHz)

Battery life*

17 hours

Battery charging time

Approximately 2.5 hours

Wireless range**

2.4 GHz

Up to 12m

*Tested at 50% headphone volume.

Microphone mute

Manual pairing of headset and wireless adapter

Part number

HX-HSCSW-BK

Table of contents

Overview 3

Microphone mute

Product code

HX-HSCSW-BK

Table of contents

Overview 3

Microphone mute

Product Model

HX-HSCSW-BK

Table of Contents

Overview 3

Product Specifications....4

Headphone Controls 5

Headphone Battery LED Indicator 6

Charging the Headphones 7

Use with PS4™ 8

Product Specifications

Headphones

Driver: 50mm dynamic neodymium magnet

Type: Closed-back over-ear

Frequency Response: 20Hz-20,000Hz

Impedance: 32 Ohm

Microphone mute

Rotate the microphone upward to mute it.

Rotate the microphone downward to unmute it.

Manually pair the headset and wireless receiver