XH210 - Pan Soba - Free user manual and instructions

USER MANUAL XH210 Soba

IMPORTANT SAFEGUARDS The following basic precautions should always be followed when using electrical appliances to reduce the risk of fire, electric shock, and/or injury:

Read all instructions carefully before using the heater.

The use of accessories not recommended by the appliance manufacturer may result in fire, electric shock or injury to persons.

Before plugging in, make sure that your electricity supply (current, voltage) is the same as that shown on the heater. If this is not the case, contact your dealer and DO NOT use the heater.

Do not position the heater immediately below a socket.

Do not let the cord hang over edge of the working surface or touch hot surfaces.

The heater becomes hot when it is in use. To avoid burns, do not touch the outer surfaces. Always use the handles when moving the heater.

Do not place combustible materials such as furniture, pillows, bedding, paper, clothes and curtains directly in front of, behind or at the side of the heater. Always maintain a safety distance of at least 3 feet (0.9m) between other objects and the heater.

Extreme caution is essential when children are near the heater or if the heater is unattended.

Young children should be supervised to ensure that they do not play with the heater.

Never leave the heater unattended. Always unplug the heater when not in use.

Never operate the heater with a damaged cord or plug, if the heater has been dropped or damaged in any way or if it is not working properly. Return the faulty heater to your authorized Soba dealer for a check up or repair.

This heater is for household use only. Do not use outdoors.

This heater must not be used in bathrooms, showers, swimming pools, laundry areas or similar indoor facilities. NEVER place the heater near a bathtub or anything else containing water.

The interior elements of the heater are hot. Sparks and arcing may occur. Consequently, never use it where petrol, paint, or flammable liquids are used or stored.

Never lay the cord under carpeting. It must always be exposed. Make sure it is placed so no one can trip over it.

To switch off the heater, turn the temperature knob and the 4-P rotary knob to "O" and disconnect the power cord from the mains socket. Never pull at or yank the cord to disconnect it outlet.

Take care that no foreign objects can get into the heater or penetrate any openings in the appliance as this could cause shock or fire or damage the heater.

To protect against fire, ensure the air intake and exhaust are not blocked. Never place the heater on soft surfaces (beds etc.) where the openings could become blocked.

Use the heater only for the purposes described in these instructions. Use for any other purpose could cause fire, electric shock or injury.

Do not use an extension cable as this could overheat and cause a fire.

CAUTION: Never open the heater! No user-serviceable parts inside! IMPORTANT WARNING If the supply cord is damaged, it must be replaced by the manufacturer or an authorised service agent or qualified electrician.

KEEP THESE INSTRUCTIONS.2

Remove your heater from its carton and unwind the cord to its full length.

Place the heater on a horizontal, flat surface.

Set the 4-P Rotary Knob to the "O" position.

Plug the Power Cord into a mains socket.

Turn the Temperature Rotary Knob to "max " position, then set the 4-P Rotary Knob at the

position. When the room has reached the desired temperature, turn the Temperature Rotary Knob slowly clockwise until you hear a click. This sets the heater to cycle on and off to maintain the required temperature.

Turn the Swing ON/OFF Switch on when you want the heater to oscillate at an angle of 90º for a better distribution of the hot air.

To switch off turn the 4-P Rotary Knob to the "0" position, then unplug from the mains socket. Note: This heater is fitted with a safety mechanism that switches it off automatically as soon as the heater is tilted.

Temperature Rotary Knob

The heater and fan are switched off.

Cooling air circulation without heating function.

Warm air circulation.

From min to max on the scale: turn to required heating temperature.

From min clockwise to the end of the scale: turns off the heater.

Turn the switch on when you want the heater to oscillate in order to enhance hot air distribution; the fan heater will move back and forward at an angle of 90º.

When the switch is turned to ON, the light integrated in the switch will light up.

AUTOMATIC SAFETY MECHANISM

There is an automatic safety mechanism integrated in the base of the heater. If the heater is knocked over or lifted up the unit will switch off automatically.

Always turn the 4-P Rotary Knob to "O" position and unplug the heater from the socket when it is not in use and before cleaning.

Use a soft, dry cloth to wipe the exterior surfaces.

Never use detergents or solvents to clean the heater.

NEVER attempt to clean the interior of the heater.

Before storing the heater for the summer, wind up the cord and pack the heater in the carton to prevent damage.