Question 1

How to access the settings on the Fysic FX6020 phone?

Accepted Answer

To access the settings of your Fysic FX6020 phone, you have two main menus depending on what you want to configure.

For the handset settings (menu HANDSET) :

Press the Menu key from the idle screen
Select the option [ HANDSET ] using the navigation keys (up/down)
Press the Confirm key (OK)

In this menu, you can configure: the ringtone, tones (key beeps, low battery, out of range), audio equalizer, language, handset name, display of time or name in standby, automatic answer to calls, and direct memory numbers.

For the base settings (menu BASE) :

Press the Menu key from the idle screen of the handset
Select the option [ BASE ] with the navigation keys
Press the Confirm key (OK)

This menu allows you to unregister handsets, adjust the FLASH pulse delay (100 mS, 300 mS, or 600 mS depending on your operator), and change your PIN code (the default factory code is 0000).

To navigate through the menus once opened, use the up and down direction keys, and press OK to confirm your selections.

Question 2

How to solve the problem of navigation arrows not working on the Fysic FX6020 phone?

Accepted Answer

If the arrow keys on your Fysic FX6020 phone are not functioning properly, several simple solutions may resolve this issue. Start by checking that the handset is properly charged by looking at the battery indicator on the LCD screen. If the batteries are low or empty, place the handset on the charging base for at least 24 hours of continuous charging.

Cleaning the buttons: This is often the cause of malfunctioning keys. Completely turn off the phone, then gently clean the arrow keys with a slightly damp cloth. Never use chemicals or harsh cleaners, as they could damage the electronics. Ensure that water does not enter the handset. Allow it to dry completely before turning it back on.

Restarting the handset: Press and hold the power button for more than 5 seconds to completely turn off the Fysic FX6020. Wait 30 seconds, then turn it back on. This restart may reset the button functions and correct temporary malfunctions due to a corrupted system file.

Checking the connection with the base: Ensure that the handset has an active connection with the base. If the antenna symbol is flashing or the text "SEARCH" appears on the screen, the handset is out of range. Move closer to the base and wait for the connection to be restored. Also, check that the base is properly powered: the adapter must be plugged into the charging port at the back of the base and into a functional power outlet.

Factory reset: If none of the previous solutions work, a complete reset may resolve the issue. Access the menu by pressing the Menu key, select the "DEFAULT" option with the arrow keys, then confirm with OK. The default PIN is 0000. Warning: this operation will erase all contacts, messages, and custom settings stored in the phone. Backup your important data before proceeding.

If the problem persists: You can also try removing the AAA batteries from the handset and unplugging it from the base for a few minutes, then reconnect everything. This may resolve some software issues. If the arrow keys remain non-functional after all these steps, the problem is likely hardware-related. Contact Fysic customer service (service@fysic.nl) or an authorized repair center to have the handset repaired or replaced under warranty (2 years). Do not attempt to disassemble the device yourself; this should be done by qualified technicians.

Question 3

How to activate the ringtone on the Fysic FX6020 phone when the volume is set to zero?

Accepted Answer

To activate the ringtone on your Fysic FX6020 phone when the volume is set to zero (ringtone disabled), follow these steps:

Increase the ringtone volume

Locate the volume buttons on the side of your phone. They are usually marked with the symbols “+” (increase) and “-” (decrease).
Press the “+” button to increase the ringtone volume. Continue until you hear a sound or see a visual indication of the volume level.

Check sound settings

Go to the Settings menu on your phone.
Look for the Sound or Notifications section.
Make sure the ringtone is enabled and that the volume is not set to silent or vibrate mode.

Once these settings are adjusted, the ringtone should activate and your phone will emit a sound for incoming calls.

User manual Fysic Phone : user manuals and guides in PDF

Models Fysic Phone most viewed

Other categories Fysic

Recent questions about Phone Fysic