JetStream T2600G-28MPS - Network switch TP-LINK - Free user manual and instructions

Product Type	Managed network switch
Brand	TP-Link
Model	JetStream T2600G-28MPS
Dimensions (W x D x H)	440 x 220 x 44 mm
Weight	3.5 kg
Power Supply	100-240 V AC, 50/60 Hz
Power Consumption	250 W (max)
Number of Ports	24 ports 10/100/1000 Mbps PoE+ + 4 SFP ports
Key Features	L2/L3 management, VLAN, QoS, IGMP snooping, Spanning Tree, link aggregation, port security, ACL, DHCP Snooping, PoE+ up to 30 W per port
Management Mode	Web Interface, CLI, SNMP, RMON, Telnet, SSH
Operating Temperature	0 °C to 40 °C
Operating Humidity	10% to 90% (non-condensing)
Maintenance and Cleaning	Unplug the device, clean with a soft dry cloth; do not use solvents
Safety	Use in a dry, well-ventilated area; do not expose to moisture or heat sources
Spare Parts and Repairability	Contact TP-Link technical support for repairs; the device contains no user-serviceable parts
General Information	28-port Gigabit PoE+ switch with optional redundant power supply, 19-inch rack mountable

Frequently Asked Questions - JetStream T2600G-28MPS TP-LINK

How to configure VLANs on the TP-Link JetStream T2600G-28MPS?

Log in to the web interface (default IP address 192.168.0.1, admin/admin). Go to Switching > VLAN > 802.1Q VLAN, create a VLAN, assign ports with type Tagged or Untagged as needed.

How to enable PoE power on a port?

PoE is enabled by default on all PoE+ ports (ports 1 to 24). To disable, go to PoE > PoE Config and uncheck the port. To check status, use PoE > PoE Status.

What to do if the device does not power on?

Check the power cable and outlet. Ensure the power switch is ON. If the Power LED does not light up, contact TP-Link support.

How to reset the switch to factory settings?

Press and hold the Reset button on the front of the switch for about 10 seconds until the LEDs flash. Release, the switch will reboot with default settings.

How to update the firmware of the T2600G-28MPS?

Download the latest firmware from TP-Link website. In the web interface, go to System Tools > Firmware Upgrade, select the .bin file and click Upgrade. Do not power off during the update.

How to configure a static IP address for the switch?

In the web interface, go to System > System Info > IP Setup, choose Static IP and enter the IP address, subnet mask, and gateway. Reboot the switch to apply.

How to enable Flow Control?

Go to Switching > Port Config, select the port, and in the Flow Control column choose Enabled. Click Apply.

How to secure access to the management interface?

Change the default admin password in System > System Info > Account. Enable HTTPS (System Tools > HTTPS) and restrict allowed IP addresses (Management > Access Control).

What cables to use for SFP connections?

Use compatible SFP modules (1000BASE-SX, LX, etc.) and LC fiber optic cables. For copper links, use Cat5e or higher Ethernet cables.

How to diagnose a network link problem?

Check the LED indicators: green for link, orange for activity. Use the Cable Test function in the interface (System Tools > Cable Test) to detect faulty cables.

USER MANUAL JetStream T2600G-28MPS TP-LINK

Easy Smart&Smart&Managed Rackmount Switch

CONTENTS

Deutsch....01

English....06

Español....11

Ελληνικά......16

Français....21

Italiano....26

Português....31

Suomi....36

Nederlands....41

Svenska....46

Norsk....51

Dansk....56

Türkçe....61

Installation

- Tischmontage

- SFP-Port

- Einschalten

Konfiguration

- Desktop Installation

To install the device on the desktop, please follow the steps below:

1. Set the device on a flat surface strong enough to support the entire weight of the device with all fittings.
2. Remove the adhesive backing papers from the rubber feet.
3. Turnover the device and attach the supplied rubber feet to the recessed areas on the bottom at each corner of the device.

- Rack Installation

To install the device in a rack, follow the instructions described below:

1. Check the grounding and stability of the rack.
2. Secure the supplied rack-mounting brackets to each side of the device with supplied screws.

1. After the brackets are attached to the device, use suitable screws (not provided) to secure the brackets to the rack.

Connection

- Ethernet Port

Connect an Ethernet port of the switch to the computer by RJ45 cable as the following figure shown.

- SFP Port

For switches with SFP ports, you can connect a SFP port to a SFP module. If an SFP transceiver is installed in a slot and has a valid link on the port, the associated RJ45 port will be disabled and cannot be used.

- Console Port

For switches with the console port, you can connect the console port with your computer by the console cable. Then you can load the CLI to manage the switch.

- Power On

Plug the female connector of the provided power cord into the power socket of the device, and the male connector into a power outlet.

Configuration

- Configure the Switch Using the GUI

1. Set the IP address of your PC in the same subnet of the switch. The IP address is 192.168.0.x("x" is any number from 2 to 254); the Subnet Mask is 255.255.255.0.
2. Open a web browser and type the default management address http://192.168.0.1 in the address field of the browser, then press the Enter key.
3. Enter admin for the default User Name and Password, both in lower case letters. Then click the Login button or press the Enter key.
4. After a successful login, you can configure the switch on the management page.

- Configure the Switch Using the CLI (Only for Smart Switches and Managed Switches)

You can log on to the switch and access the CLI to manage the switch. For the detailed instructions as to how to do this, please refer to the CLI Guide.

- Configure the Switch Using the Utility (Only for Easy Smart Switches)

You can use the Easy Smart Configuration Utility to centrally manage entire networks of the Easy Smart Switches. For the detailed instructions as to how to do this, please refer to the Utility User Guide.

Instalación

- Puerto SFP

- Encender

Configuración

- Θύρα SFP

- Θúpa Console

- Ενεργοποιήστε

Ρύθμιση

Configuration

- Configurer le switch via son interface graphique

- Accensione

Configurazione

- Configure lo Switch usando la GUI

- Ligar

Configuração

- Configurar o Switch via Interface gráfica

- Virta päällä

Konfigurointi

- Konfiguroi kytkin GUI:lla

- Inschakelen

Configuratie

- Desktop-installation

- Ström på

Konfiguration

- For å slå på

Konfigurasjon

- Tændt

Konfiguration

- Cihazı Çalıştırma

Yapılandırma

• When a product has a power on/off button, the power on/off button is one way to turn-off the product. For products without the on/off button, the only way to completely turn-off the product is to disconnect the product or the power adapter from the power source. The disconnected device shall remain readily operable.
• Do not open this product or attempt to service it; it may expose you to dangerous high voltage or other risks. Opening a sealed component or sealed product/s will void the warranty. For product servicing, please contact us.
• Do not operate this product near water.

TP-LINK Limited Product Warranty

For TP-LINK Branded Products Only.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE (OR BY COUNTRY OR PROVINCE).

TO THE EXTENT ALLOWED BY LOCAL LAW, THIS WARRANTY AND THE REMEDIES SET FORTH ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS.

TP-LINK warrants the TP-LINK branded hardware product contained in the original packaging against defects in materials and workmanship when used normally in according with TP-LINK's guidelines for some period which depends on the local service from the date of original retail purchase by the end-user purchaser.

Español

South Building(floors 1,3,4,5) and 28(floors 1-4), Central Science & Technology Park, Shennan Rd, Nanshan, Shenzhen, China

Robert-Bosch-Straße 9, 65719 Hofheim am Taunus, Germany

Unit 2 & 3 Riverview (142-144), Cardiff Road, Reading, RG1 8EW

Marathonodromou 77, Marousi 151 24, Greece

Specifications are subject to change without notice. TP-LINK is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2016 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.