CDM1094 - Drill Ferm - Free user manual and instructions

Product type	Cordless hammer drill
Brand	Ferm
Model	CDM1094
Battery voltage	14.4 V
Battery capacity	1.3 Ah
Battery type	Lithium-ion
Charger voltage	220-240 V, 50/60 Hz
No-load speed	0-900 rpm
Max. drilling diameter (concrete)	10 mm
Max. drilling diameter (steel)	8 mm
Max. drilling diameter (wood)	16 mm
Tool holder	SDS-plus
Weight	1.275 kg
Sound pressure level (L_pa)	80.5 + 3 dB(A)
Sound power level (L_wa)	91.5 + 3 dB(A)
Vibration level (main handle)	5.915 + 1.5 m/s²
Vibration level (auxiliary handle)	5.44 + 1.5 m/s²
Operating modes	Hammer drilling, drilling without impact, screwdriving
Left/right rotation	Yes
Battery status indicator	Yes (4 LEDs)
Overload and overheat protection	Yes
Protection class	Double insulation (class II)
Intended use	Hammer drilling in concrete, brick, stone; drilling without impact in wood, metal, ceramic, plastic; screwdriving
Maintenance	Clean with a soft, damp cloth; do not use solvents

Frequently Asked Questions - CDM1094 Ferm

How to change the drill bit on the Ferm CDM1094 drill?

To change the drill bit, slide the locking sleeve (2) backwards, insert the drill bit into the SDS-plus tool holder while turning slightly until it clicks, then release the sleeve. To remove, pull the sleeve backwards while holding.

How to charge the battery?

Plug the power adapter into the charger connection (8) on the machine, then plug the adapter into a 220-240 V socket. Charging starts automatically. The LEDs on the battery status indicator (4) flash during charging and remain lit when the battery is fully charged.

What is the charging time of the battery?

The charging time is not specified in the manual, but a 1.3 Ah Li-Ion battery usually charges in 1 to 2 hours.

Can I use the drill in hammer mode for all materials?

No. Use hammer mode only for concrete, brick, and stone. For wood, metal, ceramic, and plastic, set the mode selection lever to the drilling without impact position. Hammer mode would damage these materials.

How to know if the battery is low?

The battery status indicator (4) has 4 LEDs. When only one LED is lit, the charge is below 30% and it is time to recharge.

The drill stops suddenly, what to do?

This may be due to overload or overheat protection. Release the switch and wait for the battery to cool down (temperature below 70 °C). If the problem persists, check that you are not overloading and contact customer service.

What accessories are included with the drill?

The manual mentions the delivery of a chuck with a 10 mm SDS shank. Other accessories (drill bits, etc.) are not listed. Check the packaging or the retailer.

How to clean the drill?

Clean the body regularly with a soft cloth, preferably after each use. For stubborn dirt, use a slightly damp cloth with soapy water. Do not use products such as gasoline, alcohol, or ammonia.

Can I use a standard chuck on this SDS drill?

Yes, a chuck with a 10 mm SDS shank is provided for drilling without impact. It is recommended only for simple and occasional work. Never use in hammer mode with this chuck.

Is the drill suitable for professional use on construction sites?

No, the manual specifies that the machine is not suitable for use on construction sites. It is designed for domestic or DIY use.

USER MANUAL CDM1094 Ferm

Close-up of a mechanical component with curved arrows indicating motion or movement, labeled 'Fig. B' (no other text or symbols)

LI-ION DRILL

Thank you for buying this Ferm product.

By doing so you now have an excellent product, delivered by one of European leading suppliers. All products delivered to you by Ferm are manufactured according to the highest standards of performance and safety. As part of our philosophy we also provide an excellent customer service, backed by our comprehensive Warranty. We hope you will enjoy using this product for many years to come.

The numbers in the following text correspond with the pictures at page 2-3.

Read this manual carefully, before using the machine. Ensure that you know how the machine works, and how it should be operated. Maintain the machine in accordance with the instructions, and make certain that the machine functions correctly. Store this manual and other enclosed documentation with the machine

Intended use

The machine is intended for hammer drilling in concrete, brick and stone. It is also suitable for drilling without impact in wood, metal, ceramic and plastic, as well as screwdriving.

The machine is not intended for other purposes.

Not suitable for construction site usage

Please inspect the machine and accessories for transit damage.

Contents

1. Machine information
2. Safety instructions
3. Operating
4. Maintenance

1. MACHINE INFORMATION

Technical specifications

Voltage 14.4 V - 1.3 Ah

Frequency charger 50/60 Hz

Voltage charger 220-240 V

Rotational speed, not loaded 0-900 /min

Max. bit diameter

Concrete ∅ 10 mm

Steel ∅ 8 mm

Wood ∅ 16 mm

Weight 1.275 kg

Lpa 80.5+3 dB(A

Lwa 91.5+3 dB(A)

Vibration (main grip) 5.915 + 1.5 m/s^2

Vibration (auxiliary grip) 5.44 + 1.5 m/s^2

Vibration level

The vibration emission level stated in this instruction manual has been measured in accordance with a standardised test given in EN 60745; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned

• using the tool for different applications, or with different or poorly maintained accessories, may significantly increase the exposure level
• the times when the tool is switched off or when it is running but not actually doing the job, may significantly reduce the exposure level

Protect yourself against the effects of vibration by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns.

Product information

Fig. A

1. SDS-plus tool holder
2. Locking sleeve
3. Mode selection lever
4. Battery status indicator
5. Indicator for left/right rotation
6. Rotation direction switch
7. On/Off switch
8. Charger connection

2. SAFETY INSTRUCTIONS

Explanation of the symbols

Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual

Indicates electrical shock hazard

Thermic protector

Do not dispose of in household waste.

Wear ear and eye protection

Wear a dust mask. Working with wood, metals and other materials may produce dust that is harmful to health. Do not work with material containing asbestos

Indoor use only

In case of failure, the transformer is not dangerous

Do not use in rain

Specific safety instructions

For use of this machine/tool:

• Inspect the surface to be drilled for hidden electrical wiring, gas pipes or other obstacles (for example, using a metal detector).
  • Check the following points:

• Does the appliance's voltage correspond with the mains power supply voltage?
  • Are power cords, insulation and plug in good order: sound, not loose or damaged?
  • Is there a good, firm connection at the mains socket?

• Does the drill show any sign of abnormal running, overheating or excessive sparking?
• Whenever any of the problems mentioned above appear, immediately cease using the machine and have it repaired by an expert.

- Wear ear protectors. Exposure to noise can cause hearing loss.

Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and give the operator an electric shock.

Electrical safety

When using electric machines always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions and also the enclosed safety instructions.

Always check that the mains voltage is the same as on the type plate of the machine

Class II machine – Double insulation – You don't need any earthed plug

Replacement of power cords or plugs

Immediately dispose of old cords and plugs once they have been replaced.

It is dangerous to plug a loose power cord into a mains power socket.

Use of extension leads

Only ever use approved extension leads that are suitable for the power rating of the machine. The mini mum core thickness is 1.5 mm ^2 . Whenever using a reel extension lead, always fully unroll the lead.

3. OPERATING

Hammer drills require very little operator pressure. Excessive pressure on the tool can lead to unnecessary overheating of the motor, and burning of the driven tool

Exchanging and removing drill bits Fig. A

Inspect bits regularly during use. Blunt bits should be re-sharpened or replaced

• Lightly oil the bit shaft before inserting it into the chuck.
• Slide the locking sleeve (2) to the rear, and insert the bit into the chuck opening. Ensure that the keyway in the bit is seated properly in the chuck, by carefully turning the bit until it clicks into place. Release the locking sleeve.

• To remove the bit, slide and hold the locking sleeve to the rear.

Mode selection lever

Fig.B

• Set the mode selection lever to the hammer position for hammer drilling in concrete and stone. Do not use this selection for any other applications.
• Set the mode selection lever to the drilling without impact position for drilling in wood, metal, ceramic and plastic. This setting is also used for screwdriving.

The On/Off switch

Fig. A

- Switch the machine on by pressing the triggerswitch (2). When you release the triggerswitch (2) the machine will turn off.

Switching the direction of rotation

• Direction of rotation counter-clockwise: shift switch to “▶”.
• Direction of rotation clockwise: shift switch to “◀”.

Chuck

A chuck with SDS-10 shaft is shipped with the product. Please note that the machine is particularly suited for hammer drilling, the chuck should only be used for occasional simple drill work.

• To open the keyless drill chuck, rotate the chuck body in a clockwise direction until the jaws open wide enough to accept the bit.
• Insert the bit, over the full length of the jaws, into the chuck.
• Tighten the chuck jaws onto the bit by turning the chuck body in a counter clockwise direction.

The bit must be properly inserted with all three of the chuck jaws holding the bit centred in the chuck. Make sure the chuck jaws grasp the flat sides of a screwdriver bit. Failure to do so could cause the bit to be thrown from the chuck, resulting in possible serious injury or damage to the chuck

To remove a bit, open the keyless drill chuck by rotating the chuck body in a clockwise direction until the chuck jaws open and remove the bit.

The adapter can only be used for drilling/ screwdriving without impact. Never use the adapter with the machine set to Hammer mode.

Hammer drilling in concrete or brick

Caution: Stone drills can get very hot.

It may be necessary to drill with smaller bits and re-drill to nominal size so that later the plug is firmly seated.

For large bores, for instance in very hard concrete, use a smaller bit for pilot drilling and re-drill to nominal size.

Do not apply a lot of pressure on the machine, let the machine do the work, guiding the machine with light pressure is sufficient.

Hold the machine with both hands. The bit can jam, particularly with deep bores, and the machine will turn. This can lead to serious injury.

Battery status indicator

The battery status indicator shows the charge condition of the battery for a few seconds when the On/Off switch is pressed fully or halfway.

• When 1 LED is lit, the charge is less than 30% and the battery should be charged.
• When 2 LEDS are lit, the battery is charged between 30 and 70%.
• When 3 LEDS are lit, the battery is charged between 70 and 90%.
• When all 4 LEDs are lit, the battery is fully charged.

Charging the battery

- Plug the adapter directly into the charger connection (8). Charging will start when the adapter is plugged into the mains supply.

Temperature overload protection

When using as intended for, the power tool can't be subject to overload. When the load is too high or the battery temperature exceeds 70 °C, the electronic control switched off the power tool until the temperature is within working range again. The battery status indicator (4) flashes green until the On/Off switch is released.

4. MAINTENANCE

The machines are designed to function problem-free for a long period with a minimum of maintenance. Through regular cleaning and correct treatment, you help assure a long working life for your machine.

Cleaning

Clean the machine casings regularly with a soft cloth, preferably after each use. Make sure that the ventilation openings are free of dust and dirt. Remove very persistent dirt using a soft cloth moistened with soapsuds. Do not use any solvents such as gasoline, alcohol, ammonia, etc. Chemicals such as these will damage the synthetic components.

Faults

Should a fault occur, e.g. after wear of a part, please contact the service address on the warranty card. In the back of this manual you find an exploded view showing the parts that can be ordered.

Environment

To prevent damage during transport, the appliance is delivered in a solid packaging which consists largely of reusable material. Therefore please make use of options for recycling the packaging.

Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations

Warranty

For the conditions of warranty, please refer to the separately provided warranty card.

LI-ION-BOHRMASCHINE

Hamerboren in beton of baksteen

Spare parts list
CDM1094 - FCBH-1440LK

No.	Description Position
702877	Switch 4
702878	L/R button 5
702879	Function switch 9 + 10
702880	SDS head + hammer complete 13 till 54
702881	Charger *

Exploded view

CE

DECLARATION OF CONFORMITY FCBH-1440LK LI-ION ROTARY HAMMER

(EN) We declare under our sole responsibility that this product is in conformity and accordance with the following standards and regulations:
(DE) Der Hersteller erklärt eigenverantwortlich, dass dieses Produkt den folgenden Standards und Vorschriften entspricht:
(NL) Wij verklaren onder onze volledige verantwoordelijkheid dat dit product voldoet aan, en in overeenstem ming is met, de volgende standaarden en reguleringen:
(FR) Nous déclarons sous notre seule responsabilité que ce produit est conforme aux standards et directives suivants:
(ES) Declaramos bajo nuestra exclusiva responsabilidad que este producto cumple con las siguientes normas y estándares de funcionamiento:
(PT) Declaramos por nossa total responsabilida-de que este produto está em conformidade e cumpre as normas e regulamentações que se seguem:
(IT) Dichiariamo, sotto la nostra responsabilità, che questo prodotto è conforme alle normative e ai regolamenti seguenti:
(SV) Vi garanterar på eget ansvar att denna produkt uppfyller och följer följande standarder och bestämmelser:
(FI) Vakuutamme yksinomaan omalla vastuullamme, että tämä tuote täyttää seuraavat standardit ja säädökset:
(NO) Vi erklærer under vårt eget ansvar at dette produktet er i samsvar med følgende standarder og regler:
(DA) Vi erklærer under eget ansvar, at dette produkt er i overensstemmelse med følgende standarder og bestemmelser:
(HU) Felelősségünk teljes tudatában kijelentjük, hogy ez a termék teljes mértékben megfelel az alábbi szabványoknak és előírásoknak:

(CS) Na naši vlastní zodpovědnost prohlašujeme, že je tento výrobek v souladu s následujícími standardy a normami:
(SK) Vyhlasujeme na našu výhradnú zodpovednosť, že tento výrobok je v zhode a súlade s nasledujúcimi normami a predpismi:
(SL) S polno odgovornostjo izjavljamo, da je ta izdelek v skladu in da odgovarja naslednjim standardom terpredpisom:
(PL) Deklarujemy na własną odpowiedzialność, że ten produkt spełnia wymogi zawarte w następujących normach i przepisach:
(LT) Prisiimdami visą atsakomybę deklaruojame, kad śis gaminys atitinka żemiau paminétus standartus arba nuostatus:
(LV) Apgalvojam ar visu atbildību, ka šis produkts ir saskaņā un atbilst sekojošiem standartiem un nolikumiem:
(ET) Deklareerime meie ainuvastutusel, et see toode on vastavuses ja kooskõlas järgmiste standardite ja määrustega:
(RO) Declarăm prin aceasta cu răspunderea deplină că produsul acesta este în conformitate cu următoarele standarde sau directive:
(HR) Izjavljujemo pod vlastitom odgovornol,šu da je strojem ukladan sa slijedešim standardima ili standardiziranim dokumentima i u skladu sa odredbama:
(SR) Pod punom odgovornošću izjavljujemo da je usaglašen sa sledećim standardima ili normama:
(RU) Под свою ответственность заявляем, что данное изделие соответствует следующим стандартам и нормам:
(UK) На свою власну відповідальність заявляємо, що дане обладнання відповідає наступним стандартам і нормативам:
(EL) Δηλώνουμε υπεύθυνα ότι το προϊόν αυτό συμφωνεί και τηρεί τους παρακάτω κανονισμούς και πρότυπα:

EN60745-1, EN60745-2-6, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3, EN60335-1, EN60335-2-29, EN50366

2006/42/EC, 2006/95/EC, 2004/108/EC, 2002/95/EC, 2002/96/EC

Zwolle, 01-10-2011

I. Mönnink

CEO Ferm BV

It is our policy to continuously improve our products and we therefore reserve the right to change the product specification without prior notice.

Ferm BV • Lingenstraat 6 • 8028 PM • Zwolle The Netherlands