Humi Fresh - Humidifier CHICCO - Free user manual and instructions

USER MANUAL Humi Fresh CHICCO

On (I)/Stand by mode

ACCENSIONE APPARECCHIO

Grandate (Como) Italy

Before using this device, read carefully the warnings and the instructions included in this manual and keep it for future reference.

SAFETYWARNINGS

WARNING!

• This product cannot be used by children unless they are over 8 years old and are supervised and adequately instructed on the correct use of the device by a person responsible for their safety and have understood the risks involved.

• This device is not intended for use by persons with reduced physical or cognitive capacities without the necessary experience or knowledge, unless have been trained to use the device correctly by a person responsible for their safety and have understood the risks involved.

• Cleaning and maintenance of this device cannot be performed by children unless they are supervised and adequately instructed on the correct use of the device by a person responsible for their safety and have understood the risks involved.

• The device must be cleaned and dried thoroughly before every use and at the end of every cycle.

WARNING: Every three days the water tank (6) shall be emptied, cleaned thoroughly removing any deposits, fouling and films that may be present on in

ternal surfaces, rinsed with abundant cold drinking tap water and thoroughly dried.

• WARNING: The instructions to fill the tank, clean and decalcify the device and its components, refer to paragraph "CLEANING AND MAINTENANCE" of this instruction manual.
• WARNING: Before lifting, moving, tilting, cleaning/ maintaining the device and/or removing/filling the water tank (6), always switch off the device and disconnect the power cable plug (12) from the socket!.

• WARNING: The microorganisms that may be present in water or in the environment in which the device is used or stored, may grow in the water tank or in the basin (8) and be sprayed in the air causing serious health risks if the water is not replaced at least every 3 days if simultaneously all parts in contact with the water are not thoroughly cleaned and dried. For this reason, when the ON button is pressed (11) and before starting the operation, the device shall emit an acoustic and visual signal (a beep and a red flashing LED) in order to warn the user that the water must always be replaced at least every three days and that simultaneously also the tank and all parts/components in contact with the water shall be thoroughly cleaned and dried, as shown in paragraph "CLEANING AND MAINTENANCE" of this manual. Only after this warning is issued, having warned the user about replacing the water every three days and thoroughly clean the tank and all parts in contact with it, the humidifier tank be started by pressing again the ON button (11) and keeping it pressed for at least 4-5 seconds.

• WARNING: The user of this device must be aware of the fact that the levels of moisture may increase the growth of biological organisms in the environment.

• When the device is in operation, the surrounding the device and the steam outlet (5) may become damp and/or wet due to steam condensation.
• Do not allow absorbent materials such as carpe curtains or table cloths to get wet and/or become damp.
• Do not allow the area surrounding the humidifier to become damp or wet. In case of moisture, rotate the ON/adjustment button (11) to the left in order to reduce the humidifier's steam outlet flow. If the steam flow at the humidifier's outlet cannot be enough, use the humidifier intermittently.
• Do not leave water in the device when it is not in use.
  WARNING: Empty and clean thoroughly the basin (8), the water tank (6) the atomizing p transducer (9) and all parts and/or components that get in contact with the water, every 3 days, removing any deposit, fouling or film that may be present on the internal surfaces, rinse with abundant drinking tap water as shown in section "CLEANING AND MAINTENANCE" of this manual, clean thoroughly all parts before filling the water tank (6) with drinking water which has been previously and cooled down to at least 40^ .
• Empty and clean the humidifier before using Clean the humidifier before using it again.

• WARNING: This product is not a toy. Keep the device, all its parts/components, and the power cable (12) out of the reach of children.

• Children should not play with this device and must be supervised to ensure they do not play with it.

• The water level sensor (14) contains a magnetic ring that can be removed in order to allow cleaning, WARNING! pay maximum attention as the magnetic ring is a small part that must be kept out of the reach of children in order to avoid ingestion!
• After removing any packaging materials, ensure that the device has not been damaged. When in doubt, do not use the device and contact technically competent personnel, dealers or an authorised service centre of the manufacturer.
• Keep all packaging materials (plastic bags, cardboard, etc.) out of reach of children.
• Before connecting the power cable plug (12) to the socket, make sure that the device's plate data are compatible with the power supply distribution network available. The plate data are shown on a special tag located on the bottom of the device.
• Connect the power cable plug (12) to a socket that is only easily accessible by an adult.
• To shut the device down, unplug the power cable (12) from the mains.
• WARNING: Do not pull the power cable (12) or draw the device in order to unplug it from the mains.
• Always fill the water tank (6) only with boiled drinking water and let it cool down to at least 40^ C .
• WARNING: Do not pour hot or boiling water or any substances other than drinking tap water into the water tank.
• This device is intended for indoor use only; do not

leave it exposed to the sun, rain and any other atmospheric conditions

• WARNING: Always place this device only stable surfaces not accessible to children away from cribs and beds.
• Never place the device directly on or near hot surfaces, gas rings, electric warming plates, delicate surfaces, sensitive to heat, water and humidity or surfaces that are within the reach of children.
• Place this device away from other devices, materials, equipment, delicate surfaces that are sensitive to heat, humidity or steam, as they may get damaged.
• Do not place this device on the floor but always place it at least at 70-100 cm from the floor.
  DO not direct the steam towards peo ture,curtains, walls,household appliances or other objects.
• WARNING: Do not pour in the removable essence holder (4) more than 2-3 drops of essence or balsamic oils. Always pay extreme attention when pouring essences or balsamic oils in the essence holder (4), making sure not to fill it excessively and that those liquids do not flow out getting in contact with the device's external surfaces (water tank and base) as they may get irremediately damaged.
• WARNING: Never pour salts, essences, balsamic oils or other substances inside the device through the stem outlet (5), or directly into the water tank (6) or in the basin (8) as this may irremediately damage the device.
• WARNING: Never pour essences, balsamic oils or other substances in side the removable essence

holder (4) when the device is in operation.

• When the device is in operation, do not remove the lid with the removable essence holder (1).
• WARNING: Do not obstruct the filter on the ventilation openings (13), located under the device, with cloths or other objects. Any obstruction of air inlets may cause overheating of the internal electric circuit.
• Lever leave the power cable inserted in the socket when the device is unattended or not in operation. Furthermore, when in operation, avoid leaving the device and its power cable near heat sources.
• If the power cable (12) is damaged, it must be replaced by the manufacturer, by an authorized service centre or by qualified technicians, so as to avoid any risks.
• To avoid the risk of fire, do not pass the power cable (12) under rugs or near radiators, stoves and heaters.
• Do not use the device without filling the water tank (6) or without water in the basin (8).
• WARNING: To prevent any water infiltration into the base (7) when cleaning the device, remove the water contained in the tank (8) by tilting the base (7) to the opposite side of the air duct (16) (see Fig. B).
• Never immerse the device in water or other liquid or place it under running water.
• Do not touch the device with wet or damp hands and never use it with bare or wet feet.
• Do not wash the device and/or its components in a dishwasher
• Do not touch the device if it is accidentally dropped into water; immediately disconnect the power supply, lowering the lever of your central fuse box and

disconnect the power cable plug from the socket. Do not reuse the device, but contact only by the manufacturer or an authorised service centre or technically qualified personnel.

• Do not use accessories, spare parts or components not provided or supplied by the manufacturer.
• Any repair must be carried out exclusive manufacturer or by an authorised service centre or by technically qualified personnel.

WARNING!

• When using any electrical device, it is necessary to follow a few basic safety rules:
• Never cover the device when it is operating or when it is still hot.
• Do not leave the device switched on unnecessarily as it is a potential source of danger.
• The device should not be operated by means of an external timer or by means of a separate remote control.
• This device does not contain user-serviceable or reusable parts.
• This device can only be opened with special tools.
• In the event of a failure and/or poor operation of the device, switch it off immediately and the power cable plug (12) from the mains socket; do not attempt to tamper with the device and contact technically competent personnel, a dealer or an authorised service centre of the manufacturer.

• If the device is not used for an extended period of time, store it as detailed in the paragraph regarding cleaning and maintenance.

• Should the device no longer be used, after removing the power cable plug (12) from the socket, it is advisable to make it inoperative by cutting the power cable.

• Do not keep the humidifier in environment extreme temperatures.
• Never use plug adaptors, multiple plugs and/or extension wires. If their use becomes necessary, only use simple or multiple adapters and extensions that comply with current safety standards, care not to exceed the power limit indicated on the adapter and/or extension.
• Do not dispose as household waste but recycle, as it is electrical/electronic equipment (WEEE), quired by applicable laws and EU directives.
• The product's specifications may be subject to change without prior notice by the manufacturer.
• The reproduction, transmission, transcription or translation into another language, of any part and in any form of this manual is strictly prohibited without prior written consent from the manufacturer.
• This device shall be used only for its intended purpose, i.e. "humidifier for household use". Any other use is to be deemed improper and therefore dangerous.
• Artsana declines any responsibility for any damages caused by inappropriate, incorrect or unreasonable use of the device.
• In case the humidifier is sold by the purchaser or given to third party users, they must receive the instructions for the safe use of the device, and have understood the hazards involved, through reading

the instruction manual and in particular the safety warnings contained in it, which should always accompany the device.

• If there are doubts about the interpretation of any contents of this instructions manual, contact the manufacturer or the Artsana S.p.A dealer.
• These instructions are available at www.chicco.com

SYMBOLS KEY

The device complies with the essential requirements of applicable EC Directives

Alternate current

WARNING!

Clean the water tank every three days

Read the instructions for use

Instructions

On (I)/Stand by mode

For indoor use only

Do not dispose of this device or its components as normal urban refuse but separate the waste as requested by the laws in force in each country.

EN Cold humidifier Humi Fresh

WARNING! Read the safety instructions at the beginning of the manual.

Humi Fresh is the new cold steam humidifier manufactured by Chicco with a compact and harmonious design that ensures well and a healthy environment for the family. Steam allows restoring the humidity level in heated or air-conditioned rooms, preventing the formation of dry air. A properly humidified room, helps to maintain the natural protective functions of the nasal mucous and respiratory tract membranes, enabling greater defence against bacteria and polluting particles.

CONTENT

Humidifier Instruction manual

COMPONENTS OF THE UNIT (FIG. A)

1. Lid with removable essence holder
2. Removable essence holder seen from internal side of lid 1.
3. Removable essence holder fastening
4. Removable essence holder
5. Steam outlet
6. Water tank
7. Base
8. Basin
9. Piezoelectric transducer
10. LED
11. ON / standby and steam intensity adjustment button
12. Power cable with plug
13. Ventilation opening filter
14. Water level sensor
15. Tank plug
16. Air duct

INSTRUCTIONS Preliminary operations

1. Make sure that the device is perfectly clean and intact, and that the power cable plug (12) is not connected to the power socket.

2. Remove the lid with the removable essence holder (1) by lifting it vertically from the water tank (6) (Fig. C)

3. Remove the water tank (6) by lifting it vertically (Fig. C).

4. Unscrew the tank plug (15).

5. Fill the water tank (6) with previously boiled drinking tap water and cooled down to at least 40^ (Fig. D).

6. Screw the tank plug (15) on the water tank
   whole
   (6) and insert the tank into the base (7) (Fig. 1).
   E), replace the lid with removable essence holder (1) on the water tank (6).

7. If necessary, pour not more than 2-3 drops of balsamic oil or essences into the removable essence holder (4) (Fig. F), making sure that the balsamic oil or the essence does not get in contact with the external surfaces of the water tank (6) or does not enter the device through the steam outlet (5), as the device and the water tank (6) may get irreremediably damaged.

8. Always place the device as shown in paragraph SAFETYWARNINGS of this manual.

STANDBY MODE TURNOING ON THE DEVICE

1. Connect the power cable plug (12) to a socket that is only easily accessible by an adult.

2. When the humidifier is connected, the device shall emit a warning beep and the LED (10) shall illuminate in green for approximately 2 seconds, then it will become (10) red indicating that the device is in standby mode.

3. While in standby mode, the LED ( mains illuminated with a fix red light ON button (11) is not active and the steam intensity control is disabled.

4. When in standby mode, if the button (11) is pressed for 2 seconds or more, the humidifier enters the warning mode "replace the water, clean the water tank and all parts in contact with water at least every 3 days". In this mode, the device

emits a beep and the LED (10) flash that the power cable plug (12) is disconn- red to warn the user, as shown in sectioned from the socket or, if the device is in SAFETY WARNINGS of this manual, that operation, switch to standby mode by pressthe water shall be replaced at leas the everyton (11) for less than 2 seconds three, together with thorough cleaning of and then disconnect the power cable the water tank and the device; after the socket.

WARNING: Do not use rigid tools and / or chemical or abrasive products for cleaning the atomizing piezoelectric transducer (9), do not press with your fingers or with rigid tools/ materials on its surfaces as the piezoelectric transducer may get irremediately damaged.

DAILY CLEANINGWARNING!

In order to reduce the formation of bacteria, residues and fouling, clean the device daily as shown hereinafter:

sity, rotate the button (11) clock device shall emit a beep and the green LED (10) shall increase its brightness. To reduce the steam outlet intensity, rotate the button (11) counter-clockwise. At each adjustment step the device shall emit a beep and the brightness of the LED (10) shall increase or decrease according to the increase or decrease of the steam outlet intensity.
6. When level 4 (maximum) or level 1 (minimum) are reached and the button (11) is rotated further in the same direction, no acoustic signal will be emitted and the LED (10) brightness shall remain constant.
7. Press again the ON button (11) for approximately 2 seconds or less to return the device to standby mode.
8. If during normal operation there is no more water in the basin (8) and in the water tank (6), the device returns to standby mode.
9. Before using the humidifier again, clean the device as shown in paragraph CLEANING AND MAINTENANCE and repeat the operations shown in paragraphs PRE NARY OPERATIONS and STANDBY / TURING THE DEVICE ON.

CLEANING & MAINTENANCE
WARNING! Before starting any cleaning / maintenance operation on the device, make

ise, Retrieve the lid with the removable essence holder (1) by lifting it vertically without tilting it (Fig. C).

1. Remove the water tank (6) lifting it vertically (Fig. C), turn it over and remove the tank plug (15) by unscrewing it
2. Empty the water tank (6) completely ting out all residual content, clean the internal part with a sponge and rinse abundant water at least 2-3 times.
3. Remove the water level sensor (14) the tank (6), rotating it carefully count-ter-clockwise and lift it vertically (Fig. then remove the magnetic ring contained in it (Fig. G) and rinse both components with abundant water, trying to remove carefully with a sponge any limescale residues present on them.

WARNING! the removable magnetic ring is a small component, keep it out of the reach of children, risk of ingestion!

1. Release the removable essence holder (4) from the lid with removable holder (1) by MPressing the clips (3) with your thumb and index finger (Fig. H), and remove it by lifting it carefully, then rinse both components with abundant water.
2. Empty the basin (8), tilting the base as shown in Fig. B, pouring the water contained in it in the direction shown by the arrow inside the

basin. Use a sponge to remove any limescale residues in the basin. Rinse the basin (8) at least twice, pouring each time in the basin approximately 300ml of cold drinking tap water.

1. Use a soft and clean cloth to dry carefully the internal part of the tank (6) and the internal part of the basin (8). Use a soft and clean cloth to dry carefully the lid with removable essence holder (1), the removable essence holder (4), the water lever (14) and its magnetic ring.
2. Insert the magnetic ring into the level sensor (14) and reassemble the level sensor on the tank (6) rotating it carefully clockwise until reaching the stop.

WARNING! Always make sure that the magnetic ring has been inserted correctly into the level sensor, otherwise the humidifier will not work!

1. insert the removable essence holder (4) into the lid (1) making sure that it is mounted to the special supports provided (3) as shown in Fig. H.
2. Clean the outer surfaces of the device with a soft damp cloth using not use abrasive products, detergents, alcohol, solvents or similar products as they may cause permanent damages to the surfaces.
3. In order to use the device again, repeat the procedure from step 5 to step 8 shown in paragraph PRELIMINARY OPERATIONS and repeat the procedure shown in paragraph STANDBY / TURNING THE DEVICE ON.
4. WARNING! If you intend not to use the humidifier after having cleaned it, store the device and all its components in a clean and dry place, protected against dust, direct sun light and heat sources, making sure not to screw the ta (15) too tightly on the water tank (6).

WEEKLY CLEANING

During normal use of the device, the salts contained in the water could lead to the formation of scale residue in the basin (8), on

the piezoelectric transducer (9), on the water level sensor (14), on the magnetic ring, and in the water tank (6). The formation of limescale salts can occur quickly or slowly, according to the characteristics of the water delivered the area, and in particular it depends on the water hardness and on the frequency of use of the device. The harder is the water, and the faster is the formation of salt deposits.

• Limescale residues may reduce the device performance until blocking it, increasing its noise and compromising the normal operator. Besides daily cleaning of the entire device, water replacement and thorough cleaning of the tank every three days, in order to preserve the optimum conditions, the device shall be carefully cleaned weekly as follows:

• Repeat the operations shown in paragraph DAILY CLEANING.

• Pour in the water tank (6) one litre of solution of 50% water and 50% white vinegar.
• Screw the plug (15) on the water tank (6) and shake the tank for approximately 10 water conds.
• Insert the water tank (6) onto the base (7) as shown in Fig. E. Leave the sol place for at least 4 hours (even better if overnight).
• Empty the water tank and the basin (8)
• Use cold drinking tap water to rinse carefully at least 4-5 times the water tank (6), the basin (8) and the water level sensor (14) if necessary separating it from the water tank as explained in paragraph DAILY CLEANING.
• Remove any limescale residues with sponge.
• Clean and dry accurately the internal part of the water tank (6) and of the k ping the water level sensor (14) using a soft cloth.
• If necessary, repeat the procedure above until all limescale residues are completely removed.
• Insert the magnetic ring into the level sensor (14) and reassemble the level

sensor on the tank (6) rotating it carefully clockwise until reaching the stop.

WARNING! Always make sure that the magnetic ring has been inserted correctly into the level sensor, otherwise the humidifier will not work!

1. Insert the removable essence holder

(4) into the lid (1) making sure that it is mounted to the special supports provided (3) as shown in Fig. H.

1. Clean the outer surfaces of the device

with a soft damp cloth using not use abrasive products, detergents, alcohol, solvents or similar products as they may cause permanent damages to the surfaces.

1. In order to use the device again, repeat

the procedure from step 5 to step 8 shown in paragraph PRELIMINAF

OPERATIONS and repeat the procedure shown in paragraph STANDBY / TURNING THE DEVICE ON.

WARNING! If you intend not to use the humidifier after having cleaned it, store the device and all its components in a clean and dry place, protected against dust, direct sun light and heat sources, making sure not to

the tank plug (15) too tightly on the water tank (6).

water. Do

PROBLEMS AND SOLUTIONS

PROBLEM SOLUTION
If the humidifier does not work.	·Make sure that the power cable plug (12) is correctly inserted into the socket. ·Make sure that the power supply network is energized ·Make sure that the LED (10) is illuminated ·Make sure that there is water inside the tank ·Make sure that the water level sensor has been reassembled correctly and that the magnetic ring is present
If the device is very noisy.	·Carry out the normal cleaning operations as shown in paragraph CLEANING AND MAINTENANCE, then air the water tank (6) in a fresh place for 24 hours with the tank plug (15) open.
If none of the solutions indicated above solves the problem, and/or in case of operational anomalies other than those described above, bring the device to the dealer or contact Artsana S.p.A. or a technical service centre

TECHNICAL FEATURES

Model: 07502 Humi Fresh

Nominal power supply voltage:

220-240V 50/60Hz

Absorbed power: 19 W

Safety classification: Class II

Water tank capacity: 2 litres, approximately

Nebulising capacity: about 220 ± 80 ml / h

Autonomy: at least 8 hours [at minimum power]

Type of appliance: continuous operation mode

Type of atomization: Ultrasound

Weight: 1.3kg

Dimensions: 231 × 231 × 216 ~mm

Storage environmental conditions: - 40 ÷ +70^ C

Relative humidity: 10 ÷ 90%

Ref. 00008032000000

Declaration of EC compliance

This device Chicco Model 07502 with all the essential requirements and other provisions indicated in the EU Directives

2014/30/EU (electromagnetic compatibility), 2014/35/EU (Low Voltage), and 2011/65/E (RoHS).

A copy of the EC declaration can be requested from the manufacturer:

This product complies with the Directive 2012/19/EU

The crossed bin symbol on the appliance indicates that the product, at the end of its life, must be disposed of separately from domestic waste, either

by taking it to a separate waste disposal site for electric and electronic appliances or by returning it to your dealer when you buy another similar appliance. The user is responsible for taking the appliance to a special waste disposal site at the end of its life. If the disused

applicance is collected correctly as separate waste, it can be recycled, treated and posed of ecologically; this avoids a negative

impact on both the environment and health, and contributes towards the recycling of the product's materials. For further information regarding the waste disposal services available, contact your local waste disposal agency or the shop where you bought the item.

WARRANTY

The product is guaranteed against any conformity defect in normal conditions of use as provided for by the instructions for use.

The warranty shall not therefore apply in the case of damages caused by improper use, wear or accidental events.

For the duration of warranty on c defects please refer to the specific provisions of national laws applicable in the country of purchase, where provided

Manufacturer: Artsana S.p.A via

Catelli, 1 -22070 Grandate (Como) - Italy

Made in China

phormity

Saldarini

MODED'EMPLOI

On (I)/Stand by mode

Puisance absorbee:19W

Dimensions:231x231x216mm

On (I)/Stand by mode

Em modo On (I)/Stand by

Grandate (Como) Italy