Aquamax - Vacuum Cleaner Di4 - Free user manual and instructions

USER MANUAL Aquamax Di4

WE WOULD LIKE TO THANK YOU FOR CHOOSING ZELMER. WE WISH THE PRODUCT PERFORMS TO YOUR SATISFACTION AND PLEASURE.

WARNING

PLEASE READ THE INSTRUCTIONS FOR USE CAREFULLY PRIOR TO USING THE PRODUCT. STORE THESE IN A SAFE PLACE FOR FUTURE REFERENCE.

DESCRIPTION

1) Handle
2) Container lid opening button
3) Combination brush fastening
4) Plug and cord
5) Accessory compartment
6) Pump operation indicator
7) Pump switch
8) ON/OFF switch
9) Power adjustment button
10) Power level indicator
11) Cord rewind button
12) Clogged air inlet indicator
13) Water filter module
14) Cleaning liquid container
15) Parquet brush
16) Combination brush
17) Turbo brush
18) Suction hose
19) Spray unit-suction hose handle attachment
20) Crevice nozzle
21) Small brush
22) Small nozzle
23) Telescopic suction tube
24) Dust bag filter module
25) Foam filter I for air inlet
26) Foam filter I I for air inlet
27) Washing set
28) Foam filter for air outlet
29) Motor filter
30) HEPA outlet filter
31) Water filter system
32) Large atomizing nozzle
33) Small atomizing nozzle
34) Water pick-up nozzle

SAFETY INSTRUCTIONS

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

If the supply cord is damaged it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

Plug must be removed from socket-outlet before cleaning or maintaining the appliance.

This appliance is intended for use at a maximum altitude of 2000m above sea level.

IMPORTANT WARNINGS

Prior to plugging in the product, check that your mains voltage is the same as the one indicated on the product label.

The mains connection cable must not be tangled or wrapped around the product during use. Do not pull on the connection cord in order to unplug it.

Do not use, connect or disconnect the device to the mains with your hands or feet wet. Proceed according to the conservation and cleaning section of this manual for cleaning.

Unplug the product immediately from the mains in the event of any breakdown or damage and contact an authorised Technical support service.

In order to prevent any risk of danger, do not open the device. Only qualified technical personnel from the brand's Official Technical support service may carry out repairs or procedures on the device.

Any incorrect use or improper handling of the product shall render the warranty null and void. Only an authorised technical support service centre may carry out

repairs on this product.

This appliance is designed exclusively for domestic use, in no case should be a commercial or industrial use. In case of misuse or tampering with the product, it will be out of warranty.

Do not use the appliance to vacuum liquids, in dry mode (water, etc), sharp objects (pins, pins, nails, glass, etc), incandescent objects (matches, cigarettes)

Never use the turbobrush to: Polish floors, suck (Liquids, wet or damp dust, hot ash, burning objects, such as cigarettes, matches, sharp and hard items, such us: razors, pins, thumbtacks, pieces of glass, etc), flour, cement, plaster, printer or photocopier toner, etc. When wet vacuuming, do not use the vacuum cleaner to pick up liquids other than water (clean or dirty) up to 30^ .

• Empty and clean the water tank after each use. After sucking in the water, blow the hose and suction tube for about 30 seconds on full power of the vacuum cleaner.

The vacuum cleaner must be in a horizontal position during operation. Do not lift the vacuum cleaner during operation.

B&B Trends, S.L. disclaims all liability for damages that may occur to people, animals or objects, for the nonobservance of these warnings.

1. Insert the end of the suction hose to the vacuum cleaner opening so that the markings on the hose end and the vacuum cleaner housing are opposite each other and turn the hose clockwise to the position.
2. Connect the other end of the hose (handle) with the telescopic suction tube
3. Hold the ring on the pipe and set chosen length putting it in or out.
4. Assemble the appropriate nozzle or brush to the other end of the suction tube.
5. Use the following nozzle and brush for traditional vacuum cleaning with the dust bag module and vacuum cleaning with the use of water filter module: combination brush, small nozzle, small brush, crevice nozzle, parquet brush or turbo brush.
6. To clean hard surface-wooden floors, plastic floors, ceramic tiles etc. pull out the brush by pressing the switch on the nozzle according to the figure
7. The vacuum cleaner is equipped with an accessory compartment. The compartment open/close with the use of a slider. To open/close the compartment side the slider downwards/upwards and take out/put away the desired nozzle
8. The vacuum cleaner may be stored in a horizontal position; in order to this, place the fastening hook of the combination nozzle/brush into its fastening. The hose may be left attached to the vacuum cleaner, but it is important to pay attention not to leave it heavily bent during storage.
9. Close the lid.
10. Grab the plug and pull the cord out of the vacuum cleaner.

While pulling out the cord pay attention to yellow stripe which signals the end of the cord. Further attempts (pulling on cord) may result in damaging the cord

• Plug in the appliance

Before switching on the vacuum cleaner with the on/off button, make sure that the appropriate system is installed in the container

1. Switch on the vacuum cleaner by pressing the "on/off" button.
   In order to prepare the vacuum cleaner for wet operation additionally:
2. Assemble the spray unit-suction hose handle attachment.
3. Attach the end of the hose (sleeve) to the telescopic suction tube and insert the other of the hose in the small atomizing nozzle or the large atomizing nozzle until you hear a characteristic click.
4. Use the following nozzle for the wet vacuuming and wet cleaning function on to pick up water: large atomizing nozzle, small atomizing nozzle
5. Slide the stub pipe valve plug downwards
6. Insert the stub pipe of the hose to the valve in the vacuum cleaner housing.
7. Make sure the stub pipe of the fastenings snap shut.

VACUUM CLEANER FUNCTION

TRADIONAL CLEANING WITH DUST BAG

1. Press and hold the container lid opening button and lift the container lid.
2. Remove the water filter module from the container.
3. Insert the dry filtration module with the dust bag to the container.
4. The vacuum cleaner starts at the same power level it had been working before it was turned off. Set the desired power value by pressing the power adjustment buttons +/-.

The vacuum cleaner is equipped with a power level memory function. When you turn off the vacuum cleaner using the ON/OFF button, the power level is going to be stored in memory. After the vacuum cleaner is turned on next time, it is going to start working at the same power level it had been working before it was turned off.

The vacuum cleaner is equipped with a power limiting function should the inlet opening be clogged or the dust bag full. It is manifested by a pulsing limitation of the motor power and the lighting up of the clogged air inlet indicator while the vacuum cleaner is operating at full power. In such case switch off the vacuum cleaner by pressing the on/off button, unplug the appliance and clear the tubes or replace the dust bag.

DUST BAG DISASSEMBLY/ASSEMBLY

1. Remove the filter unit of the container and pull the dust bag filter module out of the container.
2. Remove the dust bag.
3. Insert the dust bag according to the arrow printed on the bag so that the lower part of the bag plate is in the slot of the housing. Press the upper part of the bag plate to the fastening element until you hear a characteristic click.
4. Insert the dry filtration module back to the container.

VACUUM CLEANING WITH THE USE OF THE WATER FILTER MODULE

1. Press and hold the lid opening button and lift the lid.
2. Insert the partition to the grooves in the container so that the shutters are directed downwards. Make sure the partition is correctly mounted in the container i.e. the partition fins should cover the protrusion in the container.
3. Fill the container with 1.3-1.5 liter of water.

The water level should be in the range marked on the wall of the container.

1. Cover the container with the filter unit.

WET VACUUMING AND WET CLEANING

Before using the wet cleaning function thoroughly vacuum the surface to be cleaned.

Before operating the vacuum cleaner make sure the container is empty and the water filter module and the filters are clean.

1. Press and hold the container lid opening button and lift the container lid.
2. Remove the container together with the water filter module from the vacuum cleaner.
3. Remove the cleaning liquid container by pulling it by the handle and lifting it upwards.
4. Open the filler cap and fill the cleaning liquid container with cleaning agent (a mixture of cleaning fluid and cold water.)

Before wet cleaning the carpet, check the colour fastness of cleaned carpet. Put a small amount of prepared solution on white cloth and clean manually the carpet at least visible place. If the cloth is dyed, it means that the carpet colours are not permanent, and the carpet cannot be cleaned using cleaning fluid.

During wet vacuuming, the vacuum cleaner is designed to suck up liquids. Limit the suction of dust and other solid fractions.

1. Insert the cleaning liquid container back to the previous position and press the container to fix it correctly.
2. Insert the container together with the water filter module (filter unit and partition) to the vacuum cleaner.

For protection against the formation of foam or at its formation, when cleaning fill the rear tank with an anti-foaming agent recommended by the company ZELMER, in the amounts specified on the label:

1. Press the pump switch.

Use only the large or small atomizing nozzle for wet vacuum cleaning.

If the nozzle does not atomize water although the pump is switched on, check if the following items are correctly installed: the cleaning liquid container, the fastening of the stub pipe in the valve in the base of the vacuum cleaner or fastening of the hose end in the atomizing nozzle, check if the atomizing nozzle is not clogged.

1. Press the button adjusting the inflow of water to the nozzle on the hose handle. If you press the button in a pulsating manner, the water shall temporarily flow in a slower manner to the nozzle. If you press and slide the button backwards, the water shall be continuously supplied to the nozzle.

The handle is also equipped with a slider to adjust the suction power. Do not uncover this opening while picking up water or using the wet cleaning function.

Do not spray the cleaning liquid in one place on the carpet for too long in order not to soak the carpet.

• You should clean the carpet in such a way that during and immediately after cleaning nobody walks on the cleaned surface. After cleaning one part of the carpet stop the spraying process and dry the carpet by sliding the nozzle back and forth. Repeat until the whole surface of the carpet is dried.
• After ending the spraying process switch off the pump and press the button adjusting the water inflow to the nozzle for a moment to "release the pressure".

The vacuum cleaner is equipped with a float which will automatically block the suction if the foam filter is heavily dirty or the liquid exceeds the maximum level. It is manifested by a pulsing limitation of the motor power and

the lighting up of the clogged air inlet indicator. In such a case switch off the vacuum cleaner by pressing the on/off button, unplug the appliance, clean the filter and empty the container.

Make sure the carpet is not soaked. It may lead to a permanent deformation of the carpet.

PICKING UP WATER

If you want to use the vacuum cleaner to vacuum liquid in the container, the vacuum cleaner should be prepared as in the case of vacuum cleaning with the use of the water filter module except that:

1. The container should be empty.
2. You are to use atomizing nozzles (large or small), large atomizing nozzle with the gathering attachment or the nozzle for picking up water.

Do not operate the vacuum cleaner with a full container! Do not vacuum large amounts of liquid at a time. Empty the water tank on a regular basis.

If the water exceeds the maximum level during vacuuming, the float will automatically block the suction. The maximum capacity of the container is about 5 l. In such a case proceed in the manner described above in the part concerning the blocking of suction caused by a dirty foam filter (pulsating motor speed)

• Switch off the vacuum by pressing the on/off button and unplug the appliance.
• Wind cord by pressing the cord rewind button.

While doing this hold the cord to make sure it is not tangled and the plug does not hit the vacuum cleaner housing.

• Turn the end of the hose until the tops of the mark on the end of the hose and on the vacuum cleaner housing are in the same position and pull the hose out of the opening.
• Remove the stub pipe of the hose by pressing the red button on the valve and pull the stub pipe.
• Disconnect the telescopic tube from the hose and the nozzle or brush.
• Pour the dirty water out of the container.
• It is recommended to wash the container, filters and partition thoroughly after each use, changing water several times.
• After using the wet cleaning function thoroughly wash all attachments used in this process (hose, tubes, accessories).

If you do not clean the above-mentioned parts or clean them insufficiently it may lead to the loss of the filtration capabilities of the inserts and foam and cause the formation of bacteria and mites. Dry all the cleaned parts thoroughly before reassembly.

FILTER DISASSEMBLY

FOAM FILTER I

It is recommended to wear rubber protective gloves while dismantling the filter

1. Grab the foam filter with your fingers and remove it from the filter unit body.
2. Wash under running water, dry and reinsert.

FOAM FILTER II

1. Open the lid of the filter unit by pulling the handle upwards.
2. Take out the filter, wash it under running water, dry and reinsert.

Do not hand wash the filter foam, do not wring it, do not wash it in washing machines. Avoid crumpling, stretching and deforming. After cleaning dry the foam in room temperature. Never dry the foam on heaters, stoves, etc.

HEPA OUTLET FILTER AND MOTOR FILTER

The HEPA outlet filter should be replaced after about 30 hours of operation (6 months) or early in case of heavy dirt.

1. Slide the slider of filter cover interlock downwards and open the filter cover.
2. Remove and replace the HEPA filter with a new one when the filter becomes dirty.
3. Remove and replace the motor filter with a new one when the filter becomes dirty.

4. It is possible to rinse the HEPA filter and the motor filter under running water. Remember to dry the above-mentioned filters before reassembly.

5. Close the filter cover and slide the interlock slider upwards.

PRODUCT DISPOSAL

This product complies with European Directive 2012/19/EU on electrical and electronic devices, known as WEEE (Waste Electrical and Electronic Equipment), establishing the legal framework applicable in the European Union for the disposal and reuse of waste electronic and electrical devices. Do not dispose of this product in the bin, instead take it to the electrical and electronic waste collection center closest to your home.

FRANÇAIS

NOUS VOUS REMERCIONS D'AVoir CHOISI ZELMER. NOUS ESPÉRONS QUE CE PRODUIT RÉPOND À VOS BESOINS ET À VOS GOUTS.

AVENTISSEMENT

VEUILLEZ LIRE ATTENTIVEMENT LE MODE D'EMPLOI AVANT D'UTILISER LE PRODUIT. CONSERVEZ-LE DANS UN ENDROIT SÜR POUR POUVOIR LE CONSULTER ULTERIEUREMENT.

DESCRIPTION

ÉLIMINATION DU PRODUIT

B&B TRENDs, SL. guarantees compliance of this product, for the use for which it is, during the period established by the legislation in force in the country of sale. In the case of breakdown during the term of this warranty, users are entitled to repair or else the replacement of the product at no charge if the former is unavailable, unless one of these options proves impossible to fulfil or is ditionate. In this case, you can then opt for a reduction in price or cancellation of the sale, which must be dealt with directly with the sales vendor. This also covers replacement of spare parts provided that the product has been used according to the recommendations specified in this manual for both cases, and has not been tampered with by any third party that is not authorised by B & B TRENDs, SL. The warranty will not cover any parts subject to wear and tear. This warranty does not affect your rights as a consumer in accordance with the provisions in Directive 1999/44/EC for member states of the European Union.

USE OF WARRANTY

Customers must contact a B&B TRENDS, SL., authorised Technical Service for repair of the product. Since any tampering of the same by anyone not authorised by B&B TRENDS, SL., or the careless or improper use of the same shall render this warranty null and void. You must keep the purchase invoice, receipt or delivery docket in order to exercise your warranty rights. For technical service and after-sales care outside the Spanish territory, please submit your query to the point of sale where you purchased the item.

BON DE GARANTIE

Check out your nearest service station at https://sat.ufesa.com/

B&B TRENDS, S.L. · C.I.F. B-86880473