DT70620 - Shears DEWALT - Free user manual and instructions

USER MANUAL DT70620 DEWALT

English (original instructions) 8

Line drawing of a robotic device with labeled components, no readable text or symbols present

KLIPPETILBEH∅R DT70620

Tillykke!

You have chosen a DEWALTtool. Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional power tool users.

EC-Declaration of Conformity MACHINERY DIRECTIVE

SHEAR ATTACHMENT DT70620

DEWALT declares that these products described are in compliance with: 2006/42/EC, EN60745-1:2009+A11:2010, EN60745-2-8:2009

For more information, please contact DEWALT at the following address or refer to the back of the manual.

The undersigned is responsible for compilation of the technical file and makes this declaration on behalf of DEWALT.

J. Bergel

Markus Rompel

Director Engineering

D-65510, Idstein, Germany

25.09.2015

WARNING: For your own safety, read the power tool instruction manual before using any accessory. Failure to heed these warnings may result in personal injury and serious damage to the tool and the accessory. When servicing this tool, use only identical replacement parts.

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

Additional Specific Safety Instructions for Shears

- Before use ensure the shear attachment is properly attached to the tool.

- To prevent inadvertent operation, lock the trigger switch in the off position when the tool is not in use or when storing the tool.

- Make sure the power tool is set to the "forward" (clockwise) directions before use.

- Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.

- DO NOT hold the shear attachment as a primary gripping surface.

- DO NOT use the shear with any kind of accessory or attachment.

- NEVER have any part of your body near the blades. Serious personal injury may result.

- Keep hands away from cutting area. A moment of inattention while operating power tools may result in serious personal injury.

- ALWAYS wear gloves when handling sheet metal. The edges are sharp and can cause serious personal injury.

- Firmly secure the piece of metal to be cut to prevent movement during cutting.

- Blades are not replaceable. DO NOT sharpen blades.

- Cut material at or below rated capacity. Max thickness to be cut is 1.3 mm.

- ALWAYS start tool before engaging material to be cut.

- If possible, cut material so scrap curl is to the left. This direction will move curl down and out of the way.

- Always wear gloves to pull scrap curl away from you during use. This will also help with speed cutting through sheet metal.

• Use shears upright. If tool is upside down, metal curl may turn toward you.
  • Always wear safety shoes to protect your feet from sharp metal debris on the floor.
• Keep all screws (thumb screws) tight. Check periodically for loosening.
• Stay clear of end pieces that may fall after being cut off. Contact with a sharp edge could result in personal injury.

CAUTION: When not in use, place tool on its side on a stable surface where it will not cause a tripping or falling hazard. Some tools with large battery packs will stand upright on the battery pack but may be easily knocked over.

Package Contents

The package contains:

1 Shear Attachment
1 Instruction manual
- Check for damage to the tool, parts or accessories which may have occurred during transport.
• Take the time to thoroughly read and understand this manual prior to operation.

Description (Fig. 1)

WARNING: Never modify the power tool or any part of it. Damage or personal injury could result.

A. Shank
B. Brace arm bracket
C. Thumb knob
D. Brace arm feet
E. Screw pocket
F. Swivel head adjustment knob
G. Blades
H. Blade adjustment screw

INTENDED USE

Your DT70620 shear attachment has been designed to be used with certain cordless DEWALT impact and drill/drivers, see Fits paragraph. The shear attachment is designed to cut 1.3 mm sheet metal, corrugated metal, duct, shingles, wire fencing, siding, wire, plastic, cardboard and some heavy duty rubber.

DO NOT use under wet conditions or in the presence of flammable liquids or gases.

DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool.

• Young children and the infirm. This appliance is not intended for use by young children or infirm persons without supervision.
• This product is not intended for use by persons (including children) suffering from diminished physical, sensory or mental abilities; lack of experience, knowledge or skills unless they are supervised by a person responsible for their safety. Children should never be left alone with this product.

FITS

DEWALT – DCD785, DCD790, DCF885, DCF895, DCD995, DCD985, DCF826, DC825, DC827, DCF886.

ASSEMBLY AND ADJUSTMENTS

IG: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury.

Shear Assembly (Fig. 1)

1. Insert shank (A) end of shear into nose of impact driver/drill. Tighten impact driver/drill chuck securely.
2. Pivot brace arm bracket (B) toward rubber over-molding at base of impact driver/drill and lock pivot brace arm bracket into place.
3. Tighten thumb knob (C) to secure shear attachment in place.

NOTE: Brace arm feet (D) will lock in place on rubber over-molding or plastic and should not pull off.

NOTE: If using an impact driver/drills without rubber over-molding on base, place the brace arm feet onto the plastic and lock into place.

NOTE: If using the DEWALT DC825 or DC827 align spring loaded screws with screw pocket (E).

Tighten Blades (Fig. 1)

Turn the blade adjustments screw (H) with a slotted screwdriver to adjust the gap of the blades (G) as needed.

Adjust Swivel Head (Fig. 1)

Loosen the swivel head adjustment knob (F) and swivel head to desired position. Tighten knob until secure before using.

Proper Hand Position (Fig. 2)

WARNING: To reduce the risk of serious personal injury, ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation of a sudden reaction.

Proper hand position requires one hand on the main handle (l), with the other hand on the material to ensure safe cutting.

MAINTENANCE

Your DEWALT power tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning.

Cleaning

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals may weaken the materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

Protecting the Environment

Separate collection. Products and batteries marked with this symbol must not be disposed of with normal household waste.

Products and batteries contain materials that can be recovered or recycled reducing the demand for raw materials. Please recycle electrical products and batteries according to local provisions. Further information is available at www.2helpU.com.

ACCESORIO DE CORTE DT70620

¡Enhorabuena!

BEWAAR ALLE WAARSCHUWINGEN EN INSTRUCTIES ALS TOEKOMSTIG REFERENTIEMATERIAAL

Director de Engenharia

DEWALT, Richard-Klinger-Strase 11,

Apertar as lâminas (Fig. 1)

D-65510, Idstein, Germany

25.09.2015

Director Engineering

D-65510, Idstein, Germany

25.09.2015

Opis (rys. [Fig.] 1)

ACCESORIU PENTRU TĂIAT DT70620

Felicitări!

ACCESORIU PENTRU TĂIAT DT70620

Director Departament Tehnic

Popis (obr. [Fig.] 1)

Popis (obr. [Fig.] 1)